Sleep Operation - Haier HSU-09HEG03/R2DB Operation Manual

Operation

Sleep Operation

Press button to enter additional options.
When display cycles to ,
Then press to enter sleep function.
1. Operation Mode
In COOL, DRY mode
1 hour after SLEEP mode starts, the temperature will become 1°C higher
than the temperature setting. After another hour the temperature rises by
another 1°C. The unit will run for a further 6 hours. The temperature is higher
than the temperature setting, so that the room temperature won't be too cold
for you to sleep.
SLEEP operation starts
SLEEP operation starts
1 hr
SLEEP operation starts SLEEP operation stops
1 hr
Rises 1
O
1 hr
Approx.6hrs
Rises 1
1 hr
Temp.setting
Rises 1
1 hr
In COOL, DRY mode
Temp.setting
Rises 1 O C
In COOL, DRY mode
1 hr
Temp.setting
2. In HEAT mode
In COOL, DRY mode
1 hour after SLEEP mode starts, the temperature will become 2°C lower than
the temperature setting. After another hour, the temperature decreases by a
further 2°C. After another 3 hours, the temperature will rise by another 1°C. The
unit will run for a further 3 hours. The temperature is lower than the temperature
setting, so that the room temperature won't be too hot for you to sleep.
Temp.setting
Temp.setting
1 hr
Decreases 2
1 hr
1 hr Decreases 2
Decreases 2
Temp.setting
1 hr
Decreases 2
3 hrs
1 hr Decreases 2 C
O
SLEEP
1 hr
3 hrs
operation starts
Decreases 2
In HEAT mode
SLEEP
operation starts
In HEAT mode
3 hrs
3. In AUTO mode
The unit operates in the corresponding sleep mode for the automatically
SLEEP
selected operation mode.
operation starts
In HEAT mode
4. In FAN mode
The SLEEP function does not operate in FAN mode.
5. Set the fan speed change when sleeping
If the fan speed is high or medium, you can set it to lower the fan
speed after you go to sleep. If it is already set at low fan speed,
it is unchanged.
Note
When the TIMER function is set, the sleeping function can't be
set up. After the sleep function is set up, if you reset the
TIMER function, the sleep function will be cancelled.
will flash.
SLEEP operation stops
Approx.6hrs
SLEEP operation stops
Approx.6hrs
Rises 1 C
O
Rises 1 O C
C
O C
Unit stop
O C
Unit stop
Unit stop
Unit stop
Unit stop
C
O
C
O
C
O
Unit stop
3 hrs
C
O
Rises 1 C
O
3 hrs
SLEEP
Rises 1 C
O
operation stops
C
O
SLEEP
3 hrs operation stops
Rises 1 C
O
SLEEP
operation stops
POWER/QUIET Operation
1. POWER Operation
When you need rapid heating or cooling, you can use this function.
Press the button to enter additional options. Press the
repeatedly until displays. When the display cycles to
flash. Then press , to confirm.
Repeat the process above to cancel.
2. QUIET Operation
You can use this function when silence is needed for rest or reading.
Press the QUIET button and the remote controller will show
Press the QUIET button again and the quiet function will be cancelled.
Note:
During POWER operation, in rapid HEAT or COOL mode, the room may show
uneven temperature distribution. Extended use of the QUIET function will provide
complete and efficient cooling of your room.
Timer On-Off Operation
1. After unit starts, select your desired operation mode.
2. Press the TIMER button to change to TIMER mode. Every time the button is
pressed, the display changes as follows:
0.5h 0.5h
TIMER ON TIMER OFF TIMER ON-OFF
Remote controller:
Then select your desired TIMER mode (TIMER ON or TIMER OFF or TIMER
ON-OFF). "ON" or "OFF" will flash.
3. Press  /  button to set the time.
 Press the button for each time, setting time in the first 12 hours increased
by 0.5 hour every time and after 12 hours, increased by 1 hour every time.
 Press the button for each time, setting time in the first 12 hours
decreased by 0.5 hour every time and after 12 hours, decreased by
1 hour every time. It can be adjusted within 24 hours.
4. Confirm timer setting
After adjusting the time, press the
ON or OFF button will not flash any more.
5. Cancel timer setting
Press the timer button repeatedly until the time display does not show.
Hints:
After replacing batteries or a power failure, the time setting should be reset.
Airflow
upward
,
BLANK
0.5h 0.5h
TIMER OFF-ON
button and confirm the time. The
Airflow Present
downward position
will
.
4