The manufacturer will not be responsible for any damage to property or to persons caused by incorrect installation or improper use of the appliance. Due to continual product development, Omega reserves the right to alter specifications and appearances without notice.
WARNINGS: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
LOCAL AUTHORITY REQUIREMENTS Before installation, unpack all parts from carton, remove all internal packaging and check for da mage. Check Gas Type and specifications plate placed on the rear of the unit, alternatively there is a second label supplied. All gas fitting work, service and repairs can only be performed by an authorised person in accordance with AS/NZS 5601 and local gas regulations.
IMPORTANT INFORMATION FOR INSTALLING THE APPLIANCE The cooker can be installed separately, a s a freestanding unit, or between kitchen u nits or between a kitchen unit and the wall. This appliance is not connected to devices which exhaust combustion products. Special attention must be focused on the prescriptions described below regarding room aeration and ventilation.
APPLIANCE GAS CONNECTION IMPORTANT: This appliance must be installed by an authorised person. WARNING: DO NOT MODIFY THIS APPLIANCE If the appliance cannot be adjusted to perform correctly, contact the service department. This appliance utilises a threaded 1/2" gas male fitting. To connect the appliance to the gas network with a flexible hose, a supplemental hose nipple fitting is needed which is supplied with the appliance.
Page 7
Check correct operation of the ignitions system and operation of the regulator and operation of the burners individually and in combination. Burner flames should be clear blue, with no yellow tipping. If the burners show any abnormality check that the burners are correctly located. If satisfactory performance cannot be obtained, contact Omega service. Important Before leaving instruct the owner in the use of the cooker it should be expressly noted that we cannot accept any liability for direct or indirect damage caused by wrong connection or improper installation.
SUPPORT LEGS The cookers are supplied with four transit supports (one for each corner). Four support legs are supplied separately and are fitted on location to the four corners of the lower support frame. Each support leg is pushed over the relevant transit support until flush with the support frame. Each leg is adjusted by screwing the lowe r section in or out as required for fitting to a 900mm bench height.
Page 9
With the legs adjusted to a nominal cooker height of 910 mm, and the splash-back fitted, anti-tilt restraint bracket can be added to the rear of the appliance. First fit the flat strap to the rear of the cooker at the centre point of the lower rear edge. Use the supplied screw (Fig. 08).
CONVERSION TO DIFFERENT TYPES OF GAS Before performing any maintenance operation, disconnect the appliance from the gas supply electricity network. REPLACING THE NOZZLES TO OPERATE WITH ANOTHER TYPE OF GAS When converting to LPG remove the NG gas regulator (if fitted) and fit LPG test point adaptor. If converting to Natural Gas, fit gas regulator Follow the instructions below to change the burner nozzles on the work surface: 1) Pull out the plug from the electric outlet to avoid any type of electric contact.
APPLIANCE ELECTRICAL CONNECTION The electric connection must comply with the current legal standards and regulations. Before making the connection, check that: The system electrical rating and the current outlet are adequate for the maximum power output of the appliance (see the label applied to the bottom of the casing).
Page 12
Three-Phase electric connection The cookers that can also be connected to three-phase systems normally are factory built for the single-phase 230V connection and are supplied with a power cord. Based on the connection system used, install the power cord type indicated in table No.3. To use the selected connection system change the jumpers on the terminal strip as indicated in the diagram of (Fig.15) Fig.
APPLIANCE U S E A N D MAINTENANCE ATTENTION: Important Warnings. For cookers resting on base ATTENTION: if the cooker rest on a base, take the measures necessary to prevent the cooker from sliding along the support base. For cookers with electric ovens ATTENTION: The unit becomes hot during use.
Page 14
Greasing the valves: If it becomes difficult to operate the valve, it should be greased immediately by following the instructions listed below: 1) Disassemble the valve body by loosening the two screws located on the body of the valve (Fig.17) Fig.
Page 15
10°C less than the temperature setting. The thermostat can control the oven elements only if an oven function has been set. For electronic timers (OF916FKXP), the timer must be off (“A” symbol off) or running.
Page 16
USING THE OVEN FUNCTION CONTROL KNOB (Fig. 20) The oven function knob is used to control the electric fan and the oven elements in set combinations in conjunction with the timer and thermostat. The electric oven is heated by 4 elements: Upper element (1200W) and grill element (1500W) combined at the top of the oven cavity.
Page 17
There are 9 functions as per below: QUICK START/DEFROST FUNCTION: This function runs the rear fans and all elements. The heat generated is too hot to cook in, but is perfect for preheating the oven (run at the required temperature until the thermostat light turns off and on a couple of time, then adjusts to the required function setting.
Page 18
USING THE ELECTRIC OVEN When using the oven for the first time it should be operated for a maximum of 30 minutes at a temperature of about 250°C to eliminate any odours generated by the internal insulation. During normal oven use, select the desired cooking temperature using the thermostat knob and wait until the orange light turns off (set temperatur e has been reached) before putting in any food.
Page 19
USING THE ELECTRONIC TIMER (OF916FKXP) Selecting and adjusting timer functions Select a timer function by pressing the function button and set the required time with the +/- buttons. Pressing the “+” button increases the time set, pressing “-“ decreases it. The count-up and count down speed increases the longer the button is held in the appropriate position.
Page 20
Any liquid that overflows from pots must always be removed using a rag. If it becomes difficult to open or close a valve, do not force it, but immediately contact the omega service department. Cleaning the enamelled parts The trivets and burner covers are cast iron with an enamel coating.
PROBLEM SOLUTION Oven or hob not working Check the electricity is turned on. Check your fuses. If the fuse continues to blow, call Omega service. Check the circuit breaker. Ensure correct knob is positioned correctly. Dry or clean ignition electrodes.
Page 22
Phone: 1300 795 572 Fax: (02) 9415 5525 Email: service@shriro.com.au Web: www.omegaappliances.com.au IN NEW ZEALAND “Omega” is a division of Monaco Corporation (Member of Shriro Australia Pty Ltd) PO Box 4399, Shortland Street, Auckland, 1140 Phone: 09 415 6000 Fax: 09 415 7060 REV. 14-2016-01 ...