Page 1
EDGER Model EV3850x4NA 3.8 Horsepower 9 Inch Blade Edge / Bevel Cut Caution: Read and follow all Safety Rules and Operating Instructions before first use of this product. F–041105C...
Page 2
PLIES ONLY WHILE THIS PRODUCT IS IN USE IN THE UNITED STATES. This Murray, Inc. Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This Limited Warranty is given in lieu of all other expressed and implied warranties including the implied warranty of merchant- ability and warranty of fitness for a particular purpose.
S Never remove the fuel tank cap or add fuel to a running or hot engine. S Never store fuel or Edger with fuel in the tank inside a building where fumes may reach an open flame.
Page 4
S Always refer to the owner’s manual instruc- tions for important details if the Edger is to be stored for an extended period. S Never store the Edger with fuel in the fuel tank inside a building where ignition sources are present such as water and space heaters, clothes dryers, and the like.
INTERNATIONAL SYMBOLS IMPORTANT: Many of the following symbols are located on your unit or on literature sup- plied with the product. Before you operate the unit, learn and understand the purpose for each symbol. Slow WARNING Thrown Objects. Keep Bystanders Away. IMPORTANT Read Owner’s Manual Before Operating...
Page 6
This will keep the front wheel in a stable position. 4. Lift the Edger out of the carton and place on a hard level surface. 1 – Control Rod 1 –...
Page 7
HOW TO RAISE THE HANDLE 1. Loosen the knobs and raise the upper handle to the upright position. See Figure 2. 2. Tighten the knobs. Make sure the knobs are to the outside of the handles as shown in Figure 2. 3.
Page 8
See an Authorized Ser- vice Center for a spark arrester for the muf- fler. As you learn how to use the Edger, pay extra attention to the following important items: nn Engine oil is at proper level.
KNOW YOUR EDGER READ THE OWNER’S MANUAL AND ALL SAFETY RULES BEFORE YOU OPERATE the Edger. To familiarize yourself with the location of the controls, compare the illustrations with your Edger. Save this manual for future reference. Engine Stop Lever...
Wide Vision Safety Mask over your eye glasses. WARNING: Debris thrown from the Edger can result in foreign objects being thrown into the eyes, which can cause severe eye dam- age. Always wear safety glasses or eye shields when operating the Edger.
Page 11
Make sure the engine stop cable moves freely. If the engine stop cable is bent or damaged, replace the cable. If the problem continues, take the Edger to an Authorized Service Center to correct the problem. HOW TO USE...
To prevent injury, keep hands and feet away from blade. IMPORTANT: Before you start the engine, move the edger to the desired location. Op- erate the controls several timer. Make sure all controls move freely. 1. Check the oil.
Keep all safety devices and shields in place. Never allow children or uninstructed adults to operate Edger. Shut off engine before unclogging blade or making re- pairs. Keep bystanders away from ma- chine. Keep away from the blade all ro- tating parts, which cause injury.
Tighten All Fasteners Check Blade For Wear Or Damage GENERAL RECOMMENDATIONS The warranty on this Edger does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must main- tain the Edger as instructed in this manual.
2. Drain the gasoline and oil from the en- gine. 3. Tip the Edger backwards on the handle. Block the top of the handle against a wall or under a bench. 4. Remove the screws from the belt guard (see Figure 11).
SERVICE AND ADJUSTMENT HOW TO REPLACE THE BLADE The blade is subject to wear and damage, such as nicks and dents. This will not gener- ally affect its function. The blade is designed to not require sharp- ening. Do not attempt to sharpen the blade. The blade is also reversible.
Page 17
Gasoline fumes can cause an explosion or a fire. When the Edger is put in storage for thirty days or more, follow the steps below to make sure the Edger is in good condition the following season.
Page 18
TROUBLE SHOOTING CHART TROUBLE Engine difficult to start Engine runs erratically Engine runs erratically Engine will not run at full Engine will not run at full speed Engine smokes excessively Cutting blade will not rotate rotate Blade will not cut properly Blade will not cut properly Excessive vibration F–041105C...
Page 19
Screw Pulley, V3L Key, Hi Pro #505 Screw, Set 100 Frame, Edger 300 Quill Assembly 301 Spring 302 Spring Pin 305 Belt, V4L 310 Blade Guard 311 Bolt, Carriage 313 Nut, 5/16–18 F–041105C ––––– 314 Flat washer 25x6 315 Blade, Edger 52052 316 Nut, 1/2–20...
Page 20
MODEL EV3850x4NA REF. FRAME ASSY. REF. REF. ENGINE WIRE FRONT WHEEL ARM 343712C F–041105C...