28 Listening in another room ....29 A few important notes Troubleshooting guide....30 Thank you for purchasing the Onkyo Audio Video Specifications ......... 31 Control Amplifier. Control positions and names ..32 Please read this manual thoroughly before making Remote controller RC-374M..
WARNING: WARNING AVIS TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, RISK OF ELECTRIC SHOCK RISQUE DE CHOC ELECTRIQUE DO NOT OPEN NE PAS OUVRIR DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated CAUTION: “dangerous voltage”...
The fuse is located inside the chassis and is not user-serviceable. If Changes or modifications not expressly approved by the manufac- power does not come on, contact your Onkyo authorized service turer for compliance could void the user's authority to operate the station.
Features Supplied accessories Check that the following accessories are supplied with this unit. Amplifier Features The number of each supplied accessory is indicated in parentheses. EUROPEAN MODELS:100 Watts minimum of continuous RMS power to each of the five channels into 6Ω, 1,000 Hz, DIN ASIAN MODELS:130 Watts minimum of continuous RMS power to each of the five channels into 6Ω, 1 kHz, EIAJ POWERFUL HIGH-CURRENT, LOW-IMPEDANCE DRIVE...
Introduction Surround System DSP (Digital Signal Processor) Since the A-DS650 is equipped with front, center, and Surround The DSP converts the musical signal into digital form and pro- amplifiers, you can produce Dolby Digital, Dolby Pro Logic, Hall, duces reflected sound from the digital signal. This is applied to the Live, Arena, and Studio Surround effects.
MULTI CHANNEL INPUT VIDEO-2 CENTER SUBWOOFER DIGITAL INPUT MODEL NO. A-DS650 form with local power supplies. Be sure to set this switch to DIGITAL 1 FRONT REMOTE SPEAKERS (OPTICAL) CAUTION: SPEAKER IMPEDANCE MONITOR DIGITAL 2 6 OHMS MIN. / SPEAKER...
DVD P R O • L O G I C SURROUND Re-EQ ENTER PARAMETER STAND-BY POWER players that have Onkyo connectors. SPEAKERS 3-D BASS MAIN REMOTE MIDNIGHT HIGH DEFINITION REC OUT MULTI SOURCE...
• A DVD or other component equipped with a digital output can be connected to the A-DS650. The digital connection must be used in conjunction with an analog connection, because if the analog cable is disconnected, the multi-room remote system, TAPE OUT and REC OUTs, and headphone will not work.
Page 9
Interference may be created between the TV and this unit. If this interference occurs, place the unit and the TV as far apart as pos- sible. • When using a playback-only VCR, connect its output to the A-DS650’s video input connector.
Page 10
• • When you power off the TV, “ ” flashes on the left side of the A-DS650’s display, and five minutes later the A-DS650 also turns off. • When the IPM system is set to ON, the video signal connected to the VIDEO-2 IN is not output from the MONITOR OUTPUT connector.
Making speaker connections Positioning speakers Speaker placement plays an important role in the reproduc- tion of Surround sound. The placement of the speakers var- ies depending on the size of the room and the wall coverings used in the room. The illustration shows an example of a lay- out for standard speaker placement.
Page 12
AC230V 50Hz SWITCHED SWITCHED DIGITAL 2 TOTAL 100W MAX. MONITOR DIGITAL 2 TOTAL 100W MAX. (COAXIAL) OUTPUT (COAXIAL) MODEL NO. A-DS650 DIGITAL 3 A-DS650 DIGITAL 3 MODEL NO. (COAXIAL) (COAXIAL) REMOTE CONTROL REMOTE CONTROL SUBWOOFER PRE OUT – – Surround Speakers...
AC outlet connections You can connect the power cord from other audio device to the rear of the A-DS650. SURROUND SPEAKERS CENTER SPEAKER FRONT MAIN SPEAKERS FRONT VIDEO-1 Since the AC outlets on the unit are the SURROUND MULTI CHANNEL...
TAPE-2 TUNER PHONO VIDEO-2 SELECTOR ® INPUT VCR-1 MONITOR VCR-2/TV A-DS650 AUDIO VIDEO CONTROL AMPLIFIER SMART SCAN CONTROLLER ENTER ENTER PARAMETER Setting up the system 3, 4 You can set up the speaker system after connecting the speakers correctly (see page 11~12). Be sure to set up the system following the instructions below.
Speaker system setup 11. Press the ENTER button to confirm the setting. 12-1 12. Set the distance from the listening position to the speakers. SMART SCAN CONTROLLER ENTER Select a value closest to the actual distance. 12-1. Rotate the SMART SCAN CONTROLLER to select “Distance”...
VIDEO-2 TAPE-1 TAPE-2 TUNER PHONO SELECTOR ® INPUT VCR-1 VCR-2/TV MONITOR VOLUME LEVEL VOLUME AUDIO VIDEO CONTROL AMPLIFIER A-DS650 π/† MUTING /REMOTE SPEAKER REMOTE CONTROLLER RC-374M MULTI-CH INPUT BASS Input selector TREBLE Listening to your favorite source SPEAKERS MAIN REMOTE 1.
Page 17
TAPE-1 TAPE-2 TUNER PHONO SELECTOR ® INPUT VCR-1 VCR-2/TV MONITOR VOLUME LEVEL VOLUME AUDIO VIDEO CONTROL AMPLIFIER A-DS650 π/† MUTING /REMOTE SPEAKER REMOTE CONTROLLER RC-374M MULTI-CH INPUT BASS Input selector TREBLE Assigning the digital inputs to input selec- tor buttons: 1.
Page 18
VIDEO-1 TAPE-1 VIDEO-2 TAPE-2 TUNER PHONO SELECTOR ® INPUT VCR-1 VCR-2/TV MONITOR LEVEL VOLUME A-DS650 AUDIO VIDEO CONTROL AMPLIFIER π/† MUTING /REMOTE SPEAKER REMOTE CONTROLLER RC-374M /REMOTE 3-D BASS BASS TREBLE SPEAKER SPEAKERS selector MAIN: This button turns on or off the speakers connected to the FRONT MAIN SPEAKERS, CENTER SPEAKER, SURROUND SPEAKERS, and SUBWOOFER terminals.
Page 19
Basic operation SUBROOM SENDING/ LEARN LEARNING SLEEP TEST POWER SLEEP DIMMER TONE MODE SOURCE SELECTOR MULTI-CH VIDEO-1 VIDEO-2 INPUT TAPE-1 TAPE-2 TUNER PHONO PROGRAMMABLE AREA TV/VIDEO POWER VOLUME POWER TV/VCR TUNER GROUP PRESET TAPE DISC SUBTITLE ON/OFF PAUSE /STEP CH SEL LEVEL VOLUME MUTING...
TAPE-1 TAPE-2 TUNER PHONO SELECTOR ® INPUT VCR-1 VCR-2/TV MONITOR LEVEL VOLUME A-DS650 AUDIO VIDEO CONTROL AMPLIFIER MUTING /REMOTE SPEAKER RC-374M REMOTE CONTROLLER ENTER SMART SCAN CONTROLLER Selecting a Surround mode SMART SCAN CONTROLLER Before using a Surround mode, make sure the System Setup SURROUND parameters have been set.
Page 21
Using Surround mode A-DS650 Parameters This chart shows how the display changes when you press the ENTER button. Rotating the SMART SCAN CONTROLLER clockwise or counterclockwise in each display can change the value and condition of whichever parameter is displayed.
Page 22
SELECTOR ® INPUT VCR-1 VCR-2/TV MONITOR A-DS650 AUDIO VIDEO CONTROL AMPLIFIER Cinema Re-Equalization Re-Equalization takes the edginess or “brightness” out of your home cinema sound, compensating for the fact that sound mixed for theaters will sound too bright when played back through speakers in the home environment.
Page 23
Using Surround mode The following illustration shows the relationship between the parameters STEREO parameters and the PARAMETER, ENTER buttons, and SMART SCAN CON- TROLLER. 1. Select the STEREO parameter. 2. Indicate whether or not you are using a subwoofer. Multi-channel input If you have set the System Setup’s Subwoofer parameter to YES, This mark indicates parameters.
Recording a source You can use the A-DS650 to record either the source you are REC OUT currently listening to or watching, or a different source. Check that the components are connected to the A-DS650 as shown MASTER VOLUME SMART SCAN CONTROLLER SYSTEM in “Audio equipment connections”...
Using a graphic equalizer Graphic equalizer A-DS650 1. Connect the graphic equalizer to the TAPE-2 connec- tors on the rear panel of the A-DS650. PLAY INPUT (REC) OUTPUT 2. If a second tape deck is used, connect it to the tape (PLAY) deck connectors on the graphic equalizer.
NOTE: • The commands of Onkyo cassette tape decks and the CD player are already stored at the TAPE and CD positions of the remote controller. • This remote controller uses infrared rays. Most remote controller codes can be memorized using the infrared system; however, depending on the degree to which the system differs, there may be some rare occasions when memorization is not possible.
Page 27
Programming remote controller codes Leaning new controller codes 1. Set the A/B-SUB ROOM/LEARN selector switch to LEARN. SUBROOM 2. Place the head of your old remote controller 2-4 inches SENDING/ LEARN LEARNED (5-10 cm) from the head of the RC-374M, laying both Switch to LEARN units on a table or a flat surface.
Speaker HR-10 (Main room) (Main room) 2. Speaker 2. Speaker (Sub-room) (Sub-room) Connecting components not equipped with Onkyo connectors 1. Connect the components to the A- DS650. Make the connections described above 4. Remote Emitter MAIN ROOM SUB ROOM HE-50 (AC) in steps 2 through 3.
We recommend that you turn off SPEAKERS MAIN to save elec- component. tricity if you are not using the A-DS650 in the main room. • • Check that the components are correctly connected.
Troubleshooting guide If a problem occurs, adjust the controls on the A-DS650 front panel to confirm that the remote controller is not malfunctioning nor has worn out batteries. Trouble Cause Remedy • • Power, then immediately no power. The amplifier protection circuitry has been Contact your Onkyo Service Center.
Specifications AMPLIFIER SECTION VIDEO SECTION Power Output Input Sensitivity and Imped- Continuous Power output ance (DIN) Video (Composite): 1 Vp-p/75 ohms × Front Main L/R channels: 100 W 2 at 6 ohms Output Level and Impedance Center channels: 100 W at 6 ohms Video (Composite): 1 Vp-p/75 ohms ×...
VIDEO-1 VIDEO-2 TAPE-1 TAPE-2 TUNER PHONO SELECTOR ® INPUT VCR-1 VCR-2/TV MONITOR A-DS650 AUDIO VIDEO CONTROL AMPLIFIER 22 21 Display SPEAKERS MAIN REMOTE SURROUND MODE OFF HALL CINEMA Re-EQ 3-DB MIDNIGHT THEATER A B TAPE-2 MONITOR DOLBY DIGITAL STUDIO LIVE...
For details, please refer to “Programming DISC remote controller codes” on pages 26-27. G CD operation buttons These buttons are used to operate an ONKYO CD player that SUBTITLE ON/OFF bears the terminal. (Refer to page 7 for connection.)