MTD 500 thru 510 Operator's Manual
Mtd log splitter operator's manual
Hide thumbs
Also See for 500 thru 510:
- Operator's manual (45 pages) ,
- Illustrated parts list (3 pages) ,
- Owner's manual (24 pages)
Table of Contents
Advertisement
Quick Links
OPERATOR'S MANUAL
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Warning:
This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 368022 Cleveland, Ohio 44136-9722.
MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722
PRINTED IN U.S.A.
Log Splitter
Model Series
500 thru 510
770-10509A.fm
FORM NO.
(7/01)
Advertisement
Table of Contents
Related Manuals for MTD 500 thru 510
Summary of Contents for MTD 500 thru 510
-
Page 1: Log Splitter
Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 368022 Cleveland, Ohio 44136-9722. MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A. -
Page 2: Table Of Contents
Troubleshooting ... 13 Parts List... 14 This Operator’s Manual is an important part of your new log splitter. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says. Before you start assembling your new equipment, please locate the model plate on the equipment and copy the information from it in the space provided below. -
Page 3: Important Safe Operation Practices
6. Always operate this machine from the operator zone(s) specified in the manual. 7. Logs should be cut with square ends prior to splitting. 8. Use your log splitter in daylight or under good artificial light. -
Page 4: Maintenance And Storage
Origin” is required in your state, see your local dealer. 16. Do not tow machine faster than 45mph. 17. See Transporting the Log Splitter section in this manual for proper towing instructions once all federal, local, or state requirements are met. -
Page 5: Assembling Your Log Splitter
SECTION 2: ASSEMBLING YOUR LOG SPLITTER This unit is shipped without gasoline or oil IMPORTANT: in the engine. - Page 6 Figure 2 Connecting the Cylinder to Beam • The log splitter is shipped with the beam in the vertical position. Pull out the vertical lock rod, rotate it back, and pivot the beam to the horizontal position until it locks. See Figure 2 & Figure 3.
-
Page 7: Know Your Log Splitter
NOTE: Some fluid may overflow from the vented dipstick as the system builds heat and the fluid expands and seeks a balanced level. Do not operate the log splitter without the IMPORTANT: proper amount of transmission fluid in the reservoir tank. -
Page 8: Operating Your Log Splitter
Never fuel machine indoors or while the engine is hot or running. NOTE: Gasoline can be added to the engine when the log splitter is in either the horizontal or vertical position; however, there are less obstructions when the unit is in the vertical position. - Page 9 Attempt to cut wood across the grain. Using The Log Splitter • Place the log splitter on level, dry, and solid ground. • Place the beam in either the horizontal or vertical position and lock in place with the appropriate locking rod.
-
Page 10: Adjusting Your Log Splitter
Hydraulic Fluid Check the hydraulic fluid level in the log splitter reservoir tank before each use. Maintain fluid level • If coupler hitch does not fit on ball, turn adjustment nut one turn counter-clockwise. - Page 11 Lubricate both sides of the beam (where it comes into contact with the splitting wedge) before each use with engine oil. The wedge plate on the log splitter is designed so the gibs on the side of the wedge plate can be removed and rotated and/or turned over for even wear.Make certain to readjust the adjustment bolts so...
-
Page 12: Conditions That Will Void Warranty
Storing Your Log Splitter • Clean the unit thoroughly. • Wipe equipment with an oiled rag to prevent rust. • Refer to engine manual for correct engine storage instructions. • Store unit in a clean, dry area. Do not store next to corrosive materials such as fertilizer. -
Page 13: Troubleshooting
SECTION 8: TROUBLESHOOTING Problem Engine fails to start 1. Spark plug wire disconnected. 2. Fuel tank empty or stale fuel. 3. Throttle control lever not in correct starting position. (If Equipped) 4. Choke not in CHOKE position. (If Equipped) 5. Engine not primed properly. 6. -
Page 14: Parts List
HYDRAULIC TROUBLESHOOTING Problem Cylinder rod will not move 1. Broken drive shaft. 2. Shipping plugs left in hydraulic 3. Set screws in coupling not adjusted 4. Loose shaft coupling. 5. Gear sections damaged. 6. Damaged relief valve. 7. Hydraulic lines blocked. 8. - Page 15 Notes...
- Page 16 Model Series 500 thru 510 12 13 24 25...
- Page 17 Model Series 500 thru 510 Ref. Part No. 718-0773 Hydraulic Cylinder 727-0634 Hydraulic Tube 710-1018 Hex Cap Screw 1/2-20 x 2.75 737-0192 90 Degree Solid Adapter 718-0481 Control Valve 737-0153 Return Elbow 737-0238 Nipple Pipe 1/2-14 710-0515 Hex Cap Screw 1/2-20 x 3.50...
- Page 20 MANUFACTURER’S LIMITED WARRANTY The limited warranty set forth below is given by MTD PRODUCTS INC (“MTD”) with respect to new merchandise purchased and used in the United States, its possessions and territories. MTD warrants this product against defects in material and...