Table of Contents
Advertisement
Installation
(Continued)
Typical horizontal installation
1
Mount a mounting bracket (L) or (R) on either side of
the control unit with a hex. bolt together with double
washers (4 mmφx 8 mm).
Mounting bracket (R) t
45
Mounting bracket (L) r
Hex. bolt with double
washers (4 mmφx 8 mm) q x 4
3
Use a cutter to cut a small cross in the carpet in
accordance with the locations of the 5 mmφ bolts of
the base brackets.
Carpet
Base bracket w x 2
Fix both the base brackets and the double-faced adhesive
tape to a mounting surface below the carpet.
Typical vertical installation
Mount the unit with the mounting bracket on either side
with a hex. bolt with double washers (4 mmφx 8 mm).
Mounting bracket (L) r
Mounting bracket (R) t
Hex. bolt with double
washers (4 mmφx 8 mm) q x 4
46
CX-DH801W
2
Select a location where the unit should be mounted.
Fix the base brackets with a double-faced adhesive
tape.
Base bracket w x 2
Double-faced adhesive tape y x 2
4
Mount the unit on the carpet with four hex. nuts (5
mmφ).
Hex. nut (5 mmφ) e x 4
Carpet
Relationship between mounting
holes and angles
C
V
V
C
B
B
H
H
C
C
A
B
B
A
L
V
R
V
A
A
H
H
Mounting bracket (L)
Mounting bracket (R)
The relationship between mounting holes and angles of the
mounting brackets (L and R) is illustrated above. Symbols
corresponding to the mounting angles are marked near the
respective holes. Select the correct holes in accordance
with the mounting angles to be used.
Electrical Connection
Cautions:
• This unit is designed for use in a car having a 12 V negative ground battery system.
• Be sure to insulate any exposed wires from a possible short-circuit from the car chassis. Bundle all cables and keep
cable terminals free from touching any metal parts.
• Note that if your car has a driving computer or a navigation computer, disconnecting the cable from the battery may
clear the memory.
• Install the cords avoiding the spots where the temperature can be extremely high.
Overview
Note:
• To prevent from damage to the unit, be sure to follow the wiring diagrams below.
• Be sure to fully plug in the connectors. Secure them with clamps and tapes.
• All other installation methods require the use of dedicated metal fittings. Consult with a qualified servicing engineer
or your dealer if other methods are required.
DVD Changer
CX-DH801W
Fuse 5A
u
Extension Cord
(BRAKE/VIDEO-CONT/ACC/BATT/DIN/RCA/GND)
Ground Lead
To a clean, bare metallic part
(Black)
of the car chassis
Parking brake connection lead
PARKING BRAKE
Be sure to wire the parking
(Blue/yellow stripe)
brake for safety and preventing
Accident.
VIDEO-CONT
Video control lead (output)
(Green/yellow stripe)
To Video control lead (input) of
other equipment
ACC
Power Lead
(Red)
To ACC power, + 12 V DC.
BATTERY 5A
Battery Lead
(Yellow)
To the car battery, continuous
+ 12 V DC.
Attaching the remote control sensor
Double-Faced Adhesive
Tape !2
Attach the
receiver.
Remote Control Sensor
Use the remote control
sensor extension cord
H
V
B
H
C
!0
if the original
V
remote control sensor
M4X5mmMAX
C
V.A.B
H.A
cord cannot reach the
DVD changer unit.
Remote-In (Mini. Pin)
REMOTE-IN
To the remote control sensor or
(Black)
Remote-out of other equipment
Remote-Out (RCA)
REMOTE-OUT
(Black)
To Remote-In of other equipment
such as TV tuner
Remote-In (RCA)
REMOTE-IN
(Black)
To Remote-out of other equipment
DIN Cable
(Black)
To the changer connector
Video output
(Yellow)
RCA Cable
Audio output (R)
(Red)
Audio output (L)
(White)
o
Fix the Remote Control
Sensor Cord with1 Cord
Clamp !1
Note: The remote control sensor should be installed where it
is not exposed to direct sunlight and where it does not inter-
fere with driver's operations.
CX-DH801W
46
o
47
Advertisement
Table of Contents
