Control Kit & Wired Remote Controller Errors - Samsung AE090JXYDEH Service Manual

4-3 CONTROL KIT & wired remote controller errors
- If an error occurs, ( ) icon will be displayed on the wired remote controller.
- Press the Test button to see the error code.
Display
101 CONTROL KIT / OUTDOOR UNIT wire connection error
162 EEPROM Error
198 Error of Terminal Block's Thermal Fuse(Open)
201 CONTROL KIT/OUTDOOR UNIT communication error (Matching error)
202 CONTROL KIT/OUTDOOR UNIT communication error (3 min)
203 Communication error between INVERTER and MAIN MICOM (6 min)
221 OUTDOOR UNIT temperature sensor error
231 condenser temperature sensor error
251 Discharge temperature sensor error
320 OLP sensor error
403 Detection of OUTDOOR UNIT compressor freezing (During cooling operation)
404 Protection of OUTDOOR UNIT when it is overload (during Safety Start, Normal operation state)
407 Comp down due to high pressure
416 Discharge of a compressor is overheated
425 Power source line missing error (only for 3-phase model)
440 Heating operation blocked (outdoor temperature over 35°C)
441 Cooling operation blocked (outdoor temperature under 9°C)
458 OUTDOOR UNIT fan1 error
461 [Inverter] Compressor startup error
462 [Inverter] Total current error/PFC over current error
463 OLP is overheated
464 [Inverter] IPM over current error
465 Compressor V limit error
466 DC LINK over/low voltage error
467 [Inverter] Compressor rotation error
468 [Inverter] Current sensor error
469 [Inverter] DC LINK voltage sensor error
470 EEPROM Read/Write error
471 [Inverter] OTP error
474 IPM(IGBT Module) or PFCM temperature sensor Error
475 OUTDOOR UNIT fan2 error
484 PFC Overload Error
485 Input current sensor error
500 IPM is overheated
554 Gas leak error
590 Inverter EEPROM Checksum error
601 Communication error between the CONTROL KIT and wired remote controller
602 Wired remote controller Master/Slave setting error
604 Communication tracking error between the CONTROL KIT and wired remote controller
607 Communication error between the Master and Salve wired remote controllers
901 Water inlet (PHE) temperature sensor error(open/short)
902 Water outlet (PHE) temperature sensor error(open/short)
903 Water outlet (backup heater) temperature sensor error.
904 DHW tank temperature sensor error
906 Outdoor Eva Inlet Temp Sensor (open/short)
Flow switch and water pump error (F/S signal is OFF for 10 sec. during the water pump signal is
911
ON)
Flow switch and water pump error (Water pump signal is OFF for 60sec during the F/S signal is
912
ON)
916 Mixing valve temp sensor (open/short)
When the product does not work during or after the concrete curing function and it displays "CC" on the wired remote controller, contact the installer to
cancel the concrete curing function.
NOTE
Samsung Electronics
Explanation
Error Source
CONTROL KIT, OUTDOOR UNIT
CONTROL KIT
CONTROL KIT
CONTROL KIT, OUTDOOR UNIT
CONTROL KIT, OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
OUTDOOR UNIT
Wired Remote Controller
Wired Remote Controller
CONTROL KIT, Wired Remote Controller
Wired Remote Controller
OUTDOOR UNIT
OUTDOOR UNIT
CONTROL KIT
CONTROL KIT
OUTDOOR UNIT
CONTROL KIT
CONTROL KIT
CONTROL KIT
57