Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Carrier 42TSV052P1
Summary of Contents for Carrier 42TSV052P1
-
Page 1: Installation Manual
SLIM CASSETTE TYPE AIR CONDITIONER INSTALLATION MANUAL Power Supply Indoor Unit Outdoor Unit 42TSV052P1 38TSV052P1 220-240V ~ 50Hz 42TSV067P1 38TSV067P1 220-240V ~ 50Hz 220-240V ~ 50Hz 42TSV080P1 38TSV080P1 42TSV110P1 38TSV110P1 220-240V ~ 50Hz 42TSV130P1 38TSV130P1 220-240V ~ 50Hz... - Page 2 Thank you very much for purchasing our air conditioner, Before using your air conditioner , please read this manual carefully and keep it for future reference.
-
Page 3: Table Of Contents
CONTENTS PAGE Install according to this installation instructions strictly. If installation is defective, it will cause water leakage, electrical shock and fire. 1. PRECAUTIONS..............When installing the unit in a small room, take measures 2. INSTALLATION INFORMATION ..........against to keep refrigerant concentration from exceeding ............ -
Page 4: Installation Information
The appliance shall be installed in accordance with national wiring If the refrigerant leaks during installation, ventilate the regulations. area immediately. Toxic gas may be produced if the refrigerant comes into the Do not operate your air conditioner in a wet room such as a bathroom place contacting with fire. -
Page 5: Attached Fittings
3. ATTACHED FITTINGS Please check whether the following fittings are of full scope. If there are some spare fittings , please restore them carefully . NAME SHAPE QUANTITY 1. Installation paper board Installation Fittings 2. Insulation sheath Tubing & Fittings 3. -
Page 6: Inspecting And Handling The Unit
This is to prevent image interference and noise in those electrical appliances. (Noise may be Fig.5-3 generated depending on the conditions under which the electric wave is generated, even if 1 meter is kept.) Table 5-1 MODEL 42TSV052P1 42TSV067P1 42TSV080P1 42TSV110P1 42TSV130P1 installation manual... -
Page 7: Install The Main Body
5.2 Install the main body The existing ceiling (to be horizontal) Cut a quadrangular hole of 880x880mm in the ceiling according to the shape of the installation paper board. (Refer to Fig.5-2) The center of the hole should be at the same position of that of the air conditioner body. - Page 8 Install the panel Relocate the installation cover. Fasten the rope of installation cover on the bolt of the Align the swing motor on the panel to the tubing joints of the installation cover. (Refer to Fig.5-14-left) body properly. ( Refer to Fig.5-10) Press the installation cover into the panel slightly.
- Page 9 1-1.5m <500mm NOTE Lean over 1/50 All the pictures in this manual are for explanation purpose only. They may be slightly different from the air conditioner you purchased(depend on model).The actual shape shall prevail. Pump-pipe clasp (the fittings) Fig.5-15 Test cap Fig.5-16 Drainage test Drainage test...
- Page 10 5.4 Install the distribution duct Conditioned air can be distributes by means of a distribution duct. MODLE (TSV052-TSV130) Ø75mm 80mm Fig.5-17 NOTE model TSV052 to TSV080 Series A=160mm; Series B=75mm model TSV110 to TSV130 Series A=160mm; Series B=95mm In case of two duct connection In case of one duct connection The air volume in duct is around 300-360m3/h for model The air volume in one duct is around 200-260m3/h for model...
-
Page 11: Outdoor Unit Installation
6. OUTDOOR UNIT INSTALLATION NOTE 6.1 Installation Place All the pictures in this manual are for explanation purpose only. They may be slightly different from the The outdoor unit should be installed in the location that air conditioner you purchased(depend on model).The meets the following requiements: actual shape shall prevail. -
Page 12: Refrigerant Pipe
Table 6-1 MODEL NOTE 38TSV All the pictures in this manual are for explanation Fig.6-2 052P1 purpose only. They may be slightly different from the air conditioner you purchased(depend on model).The 38TSV actual shape shall prevail. Fig.6-2 067P1 38TSV Fig.6-2 080P1 Concrete Foundation Foundation could be on flat and is recommended be 100-300mm... -
Page 13: Install The Connecting Pipe
The length of The max Model The type of models height drop refrigerant pipe Lean crude burr 42TSV052P1 42TSV067P1 R410A inverter Split type air 42TSV080P1 conditioner 42TSV110P1 42TSV130P1 Fig.8-1 Insert a flare nut into a pipe and flare the pipe. - Page 14 Table 8-3 Connect the indoor unit at first, then the outdoor unit. Tightening torque N.M (Turn clockwise to close) Stop Maintenance nut Bend the tubing in proper way. Do not harm to them. Valve size Shaft (valve body) (Valve lid) Ø6.4 Bend the pipe with thumb 5.4～6.6...
-
Page 15: Connect The Drain Pipe
Manifold valve Refrigerant containers shall be opened slowly. Pressure meter Multi-meter Always use protective gloves and protect your eyes when -76 cmHg charging refrigerant. Hi-lever Lo-lever Charge hose Charge hose Vacuum pump 9. CONNECT THE DRAIN PIPE Lo-lever Fig.8-7 Install the drainpipe of the indoor unit 8.2. -
Page 16: Wiring
Install the drain joint of the outdoor unit NOTE Remark per EMC Directive 2004/108/EC Fit the seal into the drain joint, then insert the drain joint into the For to prevent flicker impressions during the start of the base pan hole of outdoor, rotate 90° to securely assemble them. compressor (technical process) following... -
Page 17: Test Operation
Whether the generated wind, noise, or condensed of by the air conditioner have influenced your neighborhood. c. Whether any of the refrigerant is leaked. The Specification of Power for the invert type air conditioner(independence power supply) Table 10-1 42TSV052P1 42TSV067P1 42TSV080P1 42TSV110P1 42TSV130P1... - Page 18 CAUTION The power supply is included in the power supply above mentioned can be applied to the table. Wiring figure POWER POWER (indoor) (indoor) Fig.10-4 Power supply Power supply POWER Switch/Fuse POWER (Available locally) (outdoor) (outdoor) Power wiring (indoor) Power linking wiring (Outdoor) Indoor Unit Out door...
-
Page 19: Dr Control Box Instructions
12. DR CONTROL BOX INSTRUCTIONS When DR signal input malfunction occurs, the display area of indoor unit will display “dE” and the unit will perform the operation without DR mode. Before you start Either initiating forced cool operation under DR mode, or going into DR mode under forced cool operation is valid. - Page 20 Model B Model A 1. First remove the top panel. 2. Then remove the shield For some models , to connect panel to find the DR board. the DR board, just remove the top panel. Connect the cable with DR board Government A/C Controller (DCSR)
- Page 21 202000192390...