Page 1 I n f o r ma t i o n P r o v i d e d b y : MN 00505-QRG09-SIE Printed in the USA 6/08...
Page 2: Spare Tire
Owner’s Manual and supplementary manuals so you will have a better understanding of the vehicle’s capabilities and limitations. Your dealership and the entire staff of Toyota Motor Sales, U.S.A., Inc. wish you many years of satisfied driving in your new Sienna. Tire bag...
Page 3: Table Of Contents
Seat belts-Shoulder belt anchor Spare tire & tools Tire Pressure Monitoring (warning) System Visit your Toyota dealer for information on customizing this feature. Programmable by customer. Refer to the Owner’s Manual for instructions and more information. I n f o r ma t i o n P r o v i d e d b y : ®...
Page 4: Instrument Panel
OVERVIEW Instrument panel Overhead console Steering wheel switches Headlight, turn signal and front fog light controls Wiper and washer controls Rear window and outside rearview mirror defogger and windshield wiper de-icer switch Emergency flasher button Audio system or navigation system 115V AC Power outlet ON/OFF button AUX adapter Intuitive parking assist switch and indicator...
Page 5 Tilt and telescopic steering lock release Tire Pressure Warning System reset Power rearview mirror controls Power quarter window switch Headlight beam level control dial Conversation mirror Front personal lights Microphone Power sliding door button Power back door button Electric moonroof switch Steering wheel audio controls Telephone controls Dynamic Laser Cruise Control distance switch...
Page 6: Indicator Symbols
If indicator does not turn off within a few seconds of starting engine, there may be a malfunction. Have vehicle inspected by your Toyota dealer. For details, refer to “If a warning light turns on or a warning buzzer sounds...,”...
Page 7 Low engine oil pressure warning Open door warning Airbag SRS warning Vehicle Stability Control/Traction Control warning Low Tire Pressure Warning Low windshield washer fluid level warning Engine oil replacement reminder Third seat fold incomplete warning Theft deterrent/Engine immobilizer system indicator “AIR BAG ON”...
Page 8: Overview
OVERVIEW Keyless entry Locking operation Unlocking operation Push ONCE: Driver door TWICE: ALL doors NOTE: After unlocking, if a door is not opened within 60 seconds, all Push doors will relock for safety. Power sliding door operation (if equipped) Right side power sliding door Left side power sliding door...
Page 9: Engine Maintenance
Fuel tank door release and cap Driver seat Pull up Turn Store NOTE: Tighten until one click is heard. If the cap is not tightened enough, Check Engine “ ” indicator may illuminate. Engine maintenance Power steering fluid reservoir Windshield and rear window washer fluid tank Engine oil filler cap Engine oil level dipstick Engine coolant reservoir...
Page 10: Features/Operations
FEATURES/OPERATIONS Auto lock functions Automatic door locks can be programmed to operate in four different modes, or turned OFF. -Doors lock when shifting from Park. -Doors lock when the vehicle speed goes above approximately 12 mph. -Doors unlock when the engine key is turned to the “ACC” or “LOCK” position and driver’s door is opened.
Page 11: Lights 1 & Turn Signals
Lights & turn signals Headlights AUTO* High beam Headlights Parking lights Low beam High beam flasher * If equipped -Daytime Running Light system (if equipped) Automatically turns on the headlights at a reduced intensity. -Automatic light cut off system Automatically turns lights off after 30 seconds when any of the doors are opened and closed with the engine off.
Page 12: Parking Brake
FEATURES/OPERATIONS Windshield wipers & washers Front Single wipe Adjust interval* * Intermittent windshield Interval wipe wiper interval adjustment Pull to wash and wipe Rotate up to increase Slow interval, down to decrease interval. Fast Rear Wash and wipe Wipe Interval wipe Wash and wipe Parking brake Set: Depress...
Page 13: Moonroof
Windows Driver side Window lock switch Down Down Automatic operation (driver side only) (If equipped) Push the switch completely down or pull it completely up and release to fully open or close. To stop window midway, lightly push the switch in the opposite direction.
Page 14: Door-Power Back
FEATURES/OPERATIONS Doors-Sliding ON/OFF switch Instrument panel Push Opening/Closing Center pillar Front overhead console Open: Push Open: Push Close: Push again Close: Push again Power • Sliding doors will not fully open if the sliding door window is open. • When the engine switch is in the “ON” position, power sliding doors will open only when gear selector is in the “P”...
Page 15: Clock
Console box (if equipped) Install Remove Front seat Second row seat Lock release lever Auxiliary box The console box can be removed and installed between the front or second row seats. To remove Open the auxiliary box on the rear side, and pull the lock release lever.
Page 16: Seat Adjustments-Front
FEATURES/OPERATIONS Seat adjustments-Front Manual seat Power seat Position Height crank (driver side only) Seatback angle Lumbar support (driver side only)(If equipped) Position, cushion angle and height Seatback angle Seat adjustments-Rear Second row seat Outer Center Third row seat Manual Power Seatback release (from third row seat) Seatback release (from second row seat) Position...
Page 17: Seat Arrangements
Seats-Head restraints Front Rear Lock release button Lock release button Seat arrangements (examples) These are some possible seat arrangements. Please read the following section and refer to the Owner’s Manual for more information about seat positions. 7-passenger models 8-passenger models 7-passenger models The right seat can be placed in the inside or outboard position.
Page 18: Seats-Stowing Third Row Seats
FEATURES/OPERATIONS Seats-Tumble/Remove second row seats (1) Lower the head restraint and slide the seat to the rear-most locked position. (2) Pull the strap or lever and tumble the seat. (3) Pass the strap through the assist grip. (4) Pull and hold the strap, then fold down the seat to disengage from front hooks.
Page 19: Sunshade-Side
Seats-Stowing third row seats (power)(if equipped) Lower Push Stowing seat Returning seat Third seat fold Third seat fold incomplete warning light* incomplete warning light* Push and hold Push and hold * This light will remain ON until the seat is fully open or stowed. An alarm will also sound for 10 seconds, and the indicator will light up on the instrument panel.
Page 20: Cruise Control
FEATURES/OPERATIONS Cruise control (if equipped) Turning system ON/OFF System ON/OFF Functions Resume /Increase speed Cancel Set/Decrease speed The set speed may also be cancelled by depressing the brake pedal. The set speed may be resumed once vehicle speed reaches 25 mph. Dynamic Laser Cruise Control (if equipped) Refer to the Owner’s Manual for more details and complete safety precautions before attempting to use the “Dynamic Laser Cruise...
Page 21: Light Control-Instrument Panel
Distance control mode Push System ON/OFF The distance control mode will cruise at a set speed, decelerate to maintain a selected distance from a slower vehicle traveling in front of you, and accelerate back up to the selected speed if the vehicle in front of you changes lanes or speeds up.
Page 22: Audio
FEATURES/OPERATIONS Audio Type 1 Preset buttons - functions in other modes indicated above number. Eject CD Push to adjust tone & Push to turn balance ON/OFF Seek station/ Push to skip CD track up/down select folder Mode Station/CD View CD track scan information Type 2 additional functions...
Page 23: Telephone Controls (Bluetooth ® )
Steering wheel switches (if equipped) Volume control “ ” -In radio mode Push to select a preset station; push and hold to seek the next strong station. -In CD mode Push to skip up or down to next/previous track. “MODE” Push to turn audio ON and select an audio mode.
Page 24: Air Conditioning/Heating
FEATURES/OPERATIONS Air Conditioning/Heating Front manual Air Conditioning Air Conditioning ON/OFF Use fresh air to quickly cool interior, then change to recirculate for cooler air. Fresh or recirculated cabin air Airflow vent In “ ” or “ ” mode, use fresh air (“ ”...
Page 25 Front automatic Air Conditioning Temperature (driver side) Temperature (front passenger side) Air Conditioning ON/OFF Synchronizes front and rear temperature settings Airflow vent In “ ” or “ ” mode, use fresh air (“ ” indicator OFF) to reduce window fogging. Windshield airflow/defogger Temperature (rear passenger side) Fan speed...
Page 26: Multi-Information Display (Homelink ® ) 3
Refer to “Garage door openers,” Section 3-7 in the Owner’s Manual for more details. For programming assistance, contact the Toyota Customer Experience Center at 1-800-331-4331, or visit http://www.homelink.com. Change display information Garage door opener indicator...
Page 27: Bottle Holders
Power outlets-12V DC Instrument panel Luggage compartment Power outlets-115V AC (if equipped) ON/OFF switch Instrument panel Power outlets Luggage compartment Beside third row seat Designed for car accessories. Engine switch must be in the “ACC” or “ON” position to be used. Bottle holders Front doors Sliding doors...
Page 28: Cup Holders
FEATURES/OPERATIONS Cup holders Instrument panel Front side table Third row area Console box Rear side Front side Tray I n f o r ma t i o n P r o v i d e d b y :...
Page 29: Safety And Emergency Features
SAFETY AND EMERGENCY FEATURES Door locks Lock Unlock Doors-Child safety locks Rear door Moving the lever to “LOCK” will allow the door to be opened only from the outside. Seat belts-Shoulder belt anchor Push up, or squeeze lock release to lower Seat belt comfort guide I n f o r ma t i o n P r o v i d e d b y :...
Page 30: Seat Belts
If the tire pressure indicator flashes for more than 60 seconds and then remains on, take the vehicle to your local Toyota dealer. Note: The warning light may come on due to temperature changes or changes in tire pressure from natural air leakage. If the system has not been initialized recently, setting the tire pressures to factory specifications should turn off the light.
Page 31: Spare Tire & Tools
Abbreviation list Abbreviation/Acronym list ABBREVIATIONS MEANING 2 Wheel Drive All Wheel Drive Anti-lock Brake System Accessory Automatic Locking Retractor Average Calibration Child Restraint System Electronic Control Unit Event Data Recorder Emergency Locking Retractor English/U.S. customary system/Metric GAWR Gross Axle Weight Rating GVWR Gross Vehicle Weight Rating Emission inspection and maintenance...
Page 32 Abbreviation list ABBREVIATIONS MEANING TRAC Traction Control Variation Vehicle Identification Number Vehicle Stability Control I n f o r ma t i o n P r o v i d e d b y :...
Page 33: For Your Information
A wide variety of non-genuine spare parts and accessories for Toyota vehicles are currently available on the market. You should know that these parts are not covered by Toyota warranty and that Toyota is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
Page 34 Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by a qualified service shop or by your Toyota dealer before you scrap your vehicle.
Page 35 CAUTION General precautions while driving Driving under the influence: Never drive your vehicle when under the influ- ence of alcohol or drugs that have impaired your ability to operate your vehi- cle. Alcohol and certain drugs delay reaction time, impair judgment and reduce coordination, which could lead to an accident that will hurt or kill you, your occupants or others.
Page 36 This is a warning against anything which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your Toyota and its equipment.
Page 37 I n f o r ma t i o n P r o v i d e d b y :...
Page 38 TABLE OF CONTENTS Adjusting and operating features such as door locks, Before driving mirrors, and steering column. When driving Driving, stopping and safe-driving information. Interior fea- Air conditioning and audio systems, as well as other in- tures terior features for a comfortable driving experience. Maintenance Cleaning and protecting your vehicle, performing do-it- and care...
Page 39 Pictorial index Exterior ∗ Windshield wipers P. 191 Moon roof P. 103 Outside rear view mirrors P. 96 Hood P. 434 Parking and turn Side marker lights P. 185 signal lights P. 185 Headlights (high beam) P. 186 Headlights (low beam) P.
Page 40: Roof
Fuel filler door P. 106 Rear window defogger P. 260 ∗ Roof luggage carrier P. 219 Sliding doors P. 37 Rear window wiper P. 193 Front doors P. 33 Back door P. 47 Tires License plate lights P. 185 Rotation P.
Page 41 Pictorial index Interior Power window Seat belts P. 84 switches P. 99 Head restraints P. 82 SRS driver airbag P. 117 SRS side airbags P. 117 ∗ Floor mat P. 401 Sunshades P. 393 SRS front passenger Quarter windows airbag P.
Page 42 With garage door opener Vanity mirrors P. 384 Garage door opener switches P. 405 Trip information display P. 181 Personal/interior lights P. 362 ∗ Power back door switch P. 47 ∗ Power sliding door switches P. 38 ∗ Moon roof switch P.
Page 43 Pictorial index Interior Without garage door opener Sun visors P. 383 Vanity mirrors P. 384 Personal/interior lights P. 362 Conversation mirror P. 386 Personal/interior lights P. 362 Rear air conditioning system P. 253 Auxiliary box P. 375 SRS curtain shield airbags P.
Page 44: Power Window Switch
Inside door lock buttons P. 33 ∗ Driving position memory switches P. 80 Door lock switches P. 33 Window lock switch P. 99 Power window switches P. 99 ∗ : If equipped I n f o r ma t i o n P r o v i d e d b y :...
Page 45 Pictorial index Interior With console box Cup holders P. 370 Console box P. 365 Note pad holder P. 381 Cup holders P. 370 Cup holders P. 370 Auxiliary box P. 375 I n f o r ma t i o n P r o v i d e d b y :...
Page 46 With front seat side table Cup holders P. 370 Cup holder P. 370 Front seat side table P. 399 Auxiliary box P. 375 I n f o r ma t i o n P r o v i d e d b y :...
Page 47 Pictorial index Instrument panel Windshield wiper and washer switch P. 191 Rear window wiper and washer switch P. 193 ∗ TRAC off switch P. 216 Gauges and meters P. 174 Auxiliary box P. 375 Headlight switch P. 185 Glove box P.
Page 48 ∗ Power quarter window switch P. 101 Outside rear view mirror Headlight beam level ∗ switches P. 96 control dial P. 187 Power back door Tire pressure warning reset ∗ main switch P. 48 switch P. 454 ∗ Power sliding door main switch P.
Page 49: Talk Switch
Pictorial index Instrument panel Audio remote control Engine (ignition) switch P. 167 ∗ switches P. 292 ∗ Telephone switch P. 332 Cruise control switch P. 194, 197 ∗ Talk switch P. 332 ∗ Distance switch P. 197 I n f o r ma t i o n P r o v i d e d b y :...
Page 50 Rear window defogger switch P. 260 ∗ AUX adapter Outside rear view mirror defogger switch P. 291 P. 260 ∗ Windshield wiper de-icer switch P. 260 Power outlet main ∗ switch P. 388 Emergency flasher switch Audio system P. 262 Rear view monitor/navigation system ∗...
Page 51 Pictorial index Instrument panel With seat heater Shift lever P. 170 Seat heater switches P. 390 Shift lock override button P. 530 Auxiliary box P. 375 Without seat heater Shift lever P. 170 Shift lock override button P. 530 Auxiliary box P.
Page 52: Luggage Compartment
Pictorial index Luggage compartment Power outlet (12 V) P. 387 ∗ Power outlet (115 VAC) P. 388 ∗ Power third seat switches P. 72, 75 Luggage compartment light P. 363 Grocery bag Back door strap P. 47 hooks P. 394 Grocery bag hooks P.
Page 53 Keep the plate in a safe place such as your wallet, not in the vehicle. In the event that a key is lost, a new key can be made by your Toyota dealer using the key number plate. (→P. 531)
Page 54 1-2. Opening, closing and locking the doors Wireless remote control The wireless remote control can be used to lock and unlock the vehi- cle from outside the vehicle. Type A Locks all doors Unlocks all doors Pressing the button unlocks the driver’s door.
Page 55 1-2. Opening, closing and locking the doors Type B Locks all doors Unlocks all doors Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors. Pushing holding: Opens and closes the left side power sliding door (if equipped) Pushing...
Page 56 1-2. Opening, closing and locking the doors Operation signals Doors: A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice) Back door (type B only): A buzzer sounds and the emergency flashers flash twice to indicate that the back door has been opened/closed.
Page 57 If window tint with a metallic content or metallic objects is attached to the rear window Customization that can be configured at Toyota dealer Settings (e.g. operation signal) can be changed. (Customizable features →P. 565)
Page 58 1-2. Opening, closing and locking the doors Certification for wireless remote control For vehicles sold in the U.S.A. NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 59 1-2. Opening, closing and locking the doors NOTICE To prevent wireless remote control damage Do not subject the wireless remote control to strong shocks, expose them to high temperatures by placing them in direct sunlight, or get them wet. Do not expose the wireless remote control to electromagnetic materials or attach any material that blocks electromagnetic waves to the wireless remote control surface.
Page 60 1-2. Opening, closing and locking the doors Front doors The vehicle can be locked and unlocked using the wireless remote control, key, door lock switch or inside lock button. Wireless remote control →P. 27 Locks the door Unlocks the door Turning the key unlocks the driver's door.
Page 61 1-2. Opening, closing and locking the doors Locking the front doors from the outside without the wireless remote control or key STEP Move the inside door lock button to the lock position. STEP Close the door. The doors cannot be locked when the key is in the engine switch and either of the front door is open.
Page 62 1-2. Opening, closing and locking the doors Setting and canceling the functions To switch between set and canceled, follow the procedure below: STEP Close all the doors and turn the engine switch to the “ON” position. (Perform step 2 within 10 seconds.) Shift the shift lever to P or N, and STEP press and hold the driver's door...
Page 63 The door lock switch can be reset by unlocking all the doors with the wire- less remote control or key. Customization that can be configured at Toyota dealer Settings (e.g. unlocking function using a key) can be changed. (Customizable features →P. 565)
Page 64 1-2. Opening, closing and locking the doors Sliding doors Vehicles without power sliding doors The sliding doors can be opened and closed using the sliding door handle. The sliding door can be locked and unlocked using the inside lock knob or wireless remote control. Vehicles with power sliding doors The power sliding doors can be opened and closed using the sliding door handle, power sliding door switches or wireless remote control.
Page 65 1-2. Opening, closing and locking the doors Inside lock knobs Unlocks Locks Power sliding door switches (vehicles with power sliding doors) From front seats (type A) Push and hold the switch to open and close the right side sliding door. From front seats (type B) Push and hold the switch to open and close the following...
Page 66 1-2. Opening, closing and locking the doors From rear seats Push the switch to open and close each sliding door. Canceling the power sliding door system (if equipped) Turn the main switch off to dis- able the power sliding door sys- tem.
Page 67 1-2. Opening, closing and locking the doors Sliding door child-protector locks The sliding door cannot be opened from inside the vehicle when the child-protector lock is set. These locks can be set to prevent children from opening the sliding doors. Push down on each sliding door switch to lock both sliding doors.
Page 68 The power sliding door system must be initialized in order to ensure proper operation. To initialize it, close the sliding doors completely by hand. Customization that can be configured at Toyota dealer Settings (e.g. opening and closing operation) can be changed.
Page 69 1-2. Opening, closing and locking the doors CAUTION Caution while driving Observe the following precautions while driving. Failure to do so may cause a door to open unexpectedly and an occupant to fall out of the vehicle, resulting in death or serious injury. Always use a seat belt.
Page 70 1-2. Opening, closing and locking the doors CAUTION Operating the sliding doors Observe the following precautions. Failure to do so may cause parts of the body to be caught, resulting in seri- ous injury. When opening or closing a sliding door, thoroughly check to make sure the surrounding area is safe.
Page 71 1-2. Opening, closing and locking the doors CAUTION Sliding door closer (if equipped) In the event that the sliding door is left slightly open, the sliding door closer will automatically close it to the fully closed position. It takes several seconds before the sliding door closer begins to operate.
Page 72 “ON” position or the engine is started during automatic operation Do not attach any accessories other than genuine Toyota parts to the power sliding door. The power sliding door may not operate, causing itself to malfunction, or the power sliding door may close again after it is opened.
Page 73 1-2. Opening, closing and locking the doors NOTICE To prevent damage to your vehicle Do not apply excessive force when the sliding door closer (if equipped) is operating. Make sure there is nothing in the doorway before closing. Do not close the sliding door by applying the brakes. Doing so could cause the sliding door to be damaged.
Page 74 1-2. Opening, closing and locking the doors Back door Vehicles without power back door The back door can be opened using the back door opener. The back door can be locked and unlocked using the wireless remote control or door lock switch. Vehicles with power back door The power back door can be opened and closed using the power back door switch or wireless remote control.
Page 75 1-2. Opening, closing and locking the doors As the power back door starts to open or close automatically, two beeps sound and the turn signal lights flash twice. Wireless remote control (vehicles with power back door) →P. 27 Canceling the power back door system (vehicles with power back door) Turn the main switch off to dis- able the power back door sys- tem.
Page 76 1-2. Opening, closing and locking the doors Back door strap Use the strap when closing the back door. If the back door opener is inoperative The back door can be operated from the inside. Remove the cover. STEP Vehicles without power back door Pull the lever.
Page 77 1-2. Opening, closing and locking the doors The power back door can be operated when (vehicles with power back door) The engine switch is in the “ON” position and the shift lever is in P. The back door is unlocked. Jam protection function (vehicles with power back door) If anything obstructs the power back door while it is closing or opening, the back door will automatically operate in the opposite direction.
Page 78 1-2. Opening, closing and locking the doors CAUTION Caution while driving Keep the back door closed while driving. If the back door is left open, it may hit near-by objects while driving or lug- gage may be unexpectedly thrown out, causing an accident. In addition, exhaust gases may enter the vehicle, causing death or a seri- ous health hazard.
Page 79 Doing so may cause hands to be caught or the back door damper stay to break, causing an accident. Do not attach any accessories other than genuine Toyota parts to the back door. Such additional weight on the back door may cause the back door to fall closed again after it is opened.
Page 80 1-2. Opening, closing and locking the doors CAUTION Back door closer (if equipped) In the event that the back door is left slightly open, the back door closer will automatically close it to the fully closed position. It takes several seconds before the back door closer begins to operate.
Page 81 “ON” position or the engine is started during automatic operation Do not attach any accessories other than genuine Toyota parts to the back door. The power back door may not operate, causing itself to malfunction, or the back door may fall closed again after it is opened.
Page 82 1-2. Opening, closing and locking the doors NOTICE To prevent damage to the back door components Do not apply any force, paint or let any other foreign matter on the damper. Do not apply excessive force when the back door closer is operating. Make sure there is nothing in the doorway before closing.
Page 83 1-3. Adjustable components (seats, mirrors, steering wheel) Front seats Manual seat Passenger’s seat Driver’s seat Seat position adjustment lever Seatback angle adjustment lever Vertical height adjustment lever Lumbar support adjustment knob Seatback folding lever (if equipped) I n f o r ma t i o n P r o v i d e d b y :...
Page 84 1-3. Adjustable components (seats, mirrors, steering wheel) Power seat Seat position adjustment switch Seatback angle adjustment switch Seat cushion (front) angle adjustment switch (driver’s side only) Vertical height adjustment switch (driver’s side only) Lumbar support switch (driver’s side only) Seatback table (if equipped on manual seat) The folded seat can be used as a temporary table.
Page 85 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION Seat adjustment Be careful that the seat does not hit passengers or luggage. Do not recline the seat more than necessary when the vehicle is in motion to reduce the risk of sliding under the lap belt. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of...
Page 86 1-3. Adjustable components (seats, mirrors, steering wheel) Second seats Center seat Outer seats Seat position adjustment lever Seatback angle adjustment lever/strap (from front) The seatback can be folded down by this lever/strap. Seatback angle adjustment strap (from rear) The seatback can be folded down by this strap. Tumbling the seat for third seat entry The second seats can be tumbled for access to the third seat.
Page 87 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION Seat adjustment Be careful that the seat does not hit passengers or luggage. Do not recline the seat more than necessary when the vehicle is in motion to reduce the risk of sliding under the lap belt. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of...
Page 88 1-3. Adjustable components (seats, mirrors, steering wheel) Third seats Manual seat Seatback angle adjustment strap Power seat Seatback angle adjustment switch I n f o r ma t i o n P r o v i d e d b y :...
Page 89 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION Seat adjustment Be careful that the seat does not hit passengers or luggage. Do not recline the seat more than necessary when the vehicle is in motion to reduce the risk of sliding under the lap belt. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of...
Page 90 1-3. Adjustable components (seats, mirrors, steering wheel) Seating configurations Tumbling the second seats Before tumbling the second seats Stow the seat belt buckles. STEP Outer seats: Use the seat belt STEP hangers to prevent the belts from being tangled. Tumbling the second seats Lower the head restraints to the STEP lowest position and slide the seat...
Page 91 1-3. Adjustable components (seats, mirrors, steering wheel) 7-passenger models: Pull the STEP armrests up. Outer seats: Fold down the seat- STEP back while pulling the seatback angle adjustment lever or strap and swing up the seat. If the front seat is in the way, adjust it so it will not interfere.
Page 92 1-3. Adjustable components (seats, mirrors, steering wheel) Removing the second seats The seats can be removed after tumbling the second seats. Before removing the second seats Tumble the second seats. (→P. 63) Removing the second seats Pull and hold the front leg STEP release strap and fold down the seat.
Page 93 1-3. Adjustable components (seats, mirrors, steering wheel) Installing the second seats When you install the second seats, be sure to place them where the seats are originally positioned because the second seats are not interchangeable. Outer seats You can distinguish the original Front of vehicle seat position by the position of the front leg pins and the shape...
Page 94 1-3. Adjustable components (seats, mirrors, steering wheel) Installing the second seats Align the front leg hooks with the STEP rear strikers, then swing up the seat. Make sure the front legs align with the strikers before swinging up the seat. Fold down the seat and engage STEP the rear leg locks.
Page 95 1-3. Adjustable components (seats, mirrors, steering wheel) Center seat: Disengage the rear STEP leg locks by pulling the rear leg release lever. STEP Reinstall the seat following the correct procedure. Changing the installed position Outer seat (7-passenger models) The right side second seat can be moved to the inside when the console box (if equipped) is not installed between the second...
Page 96 1-3. Adjustable components (seats, mirrors, steering wheel) Center seat (8-passenger models) The second center seat can be used in the forward position. To use the second center seat in the forward position, install it according to the following procedure: STEP Slide the front seats forward and stand the seatbacks in the upright position.
Page 97 1-3. Adjustable components (seats, mirrors, steering wheel) Align the front leg hooks with the STEP rear strikers of the foremost pair. Then swing up the seat. Push the foot pedal forward to STEP securely latch the front leg locks. Make sure the front legs are locked securely, fold down the seat and engage the rear leg locks.
Page 98 1-3. Adjustable components (seats, mirrors, steering wheel) Folding the third seats (manual seats) Before folding the third seats Lower the head restraints to the STEP lowest position and stow the seat belt buckles. STEP Stow the center seat belt. (→P. 86) Folding the third seats Pull the “TO FOLD/LIFT SEAT- BACK”...
Page 99 1-3. Adjustable components (seats, mirrors, steering wheel) Folding the third seats (power seats) You can operate the power third seats when the engine switch is in the “ACC” or “LOCK” position, and/or the shift lever is in P. Before folding the third seats Lower the head restraints to the STEP lowest position and stow the seat...
Page 100 1-3. Adjustable components (seats, mirrors, steering wheel) Stowing the third seats (manual seats) Before stowing the third seats Fold down the seatbacks. (→P. 71) Stowing the third seats Pull and hold the “TO STOW/ STEP USE” strap and lift up the seat rearward.
Page 101 1-3. Adjustable components (seats, mirrors, steering wheel) Returning the third seats Pull and hold the “TO STOW/ STEP USE” strap and lift up the seat rearward. Push the seat forward and then STEP engage the front leg locks. Make sure the front legs are locked securely.
Page 102 1-3. Adjustable components (seats, mirrors, steering wheel) Stowing the third seats (power seats) You can operate the power third seats when the engine switch is in the “ACC” or “LOCK” position, and/or the shift lever is in P. Before stowing the third seats Lower the head restraints to the STEP lowest position and stow the seat...
Page 103 1-3. Adjustable components (seats, mirrors, steering wheel) Returning the third seats Push and hold the returning switch until the seat cushion is locked. A beep sounds twice to indicate the start of the operation. The beep sounds again twice when operation is completed.
Page 104 1-3. Adjustable components (seats, mirrors, steering wheel) “3RD SEAT” warning light (power third seat) The warning light comes on if the third seat operation is not yet complete when the engine switch is in the “ON” position. CAUTION When seats are moved Observe the following precautions.
Page 105 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION Tumbling the second seats In order to prevent personal injury in a collision or sudden stop, do not allow passengers to sit in the third seats when a second seat is tumbled. When tumbling the second seats, fix the seats securely by adjusting the length of the seat's holding strap.
Page 106 1-3. Adjustable components (seats, mirrors, steering wheel) NOTICE To prevent damage to the seat Avoid putting heavy loads on a folded seat that is being used as a tempo- rary table. Before folding a second seat as preparation for removal or tumbling the seat, the seat belt buckles must be stowed.
Page 107 1-3. Adjustable components (seats, mirrors, steering wheel) Driving position memory (if equipped) Your preferred driving position (the position of the driver’s seat and outside rear view mirrors) can be memorized and recalled with the touch of a button. Two different driving positions can be entered into memory. Entering a position to memory Check that the shift lever is set in P.
Page 108 1-3. Adjustable components (seats, mirrors, steering wheel) Operating the driving position memory after turning the engine switch to the “LOCK” position Memorized positions can be activated up to 30 seconds after the driver's door is opened, even after turning the engine switch to the “LOCK” position. To cancel memorized position recall Perform any of the following operations.
Page 109 1-3. Adjustable components (seats, mirrors, steering wheel) Head restraints Vertical adjustment Down Push the head restraint down while pushing the lock release button. Lock release button Removing the head restraints Pull the head restraint up while pushing the lock release button. Adjusting the height of the head restraints Make sure that the head restraints are adjusted so that the center of the head...
Page 110 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION Head restraint precautions Observe the following precautions regarding the head restraints. Failure to do so may result in death or serious injury. Use the head restraints designed for each respective seat. Adjust the head restraints to the correct position at all times. After adjusting the head restraints, push down on them and make sure they are locked in position.
Page 111 1-3. Adjustable components (seats, mirrors, steering wheel) Seat belts Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. Correct use of the seat belts l Extend the shoulder belt so that it comes fully over the shoulder, does come into contact with the...
Page 112 1-3. Adjustable components (seats, mirrors, steering wheel) Adjusting the height of the belt (front seats) Down Move the height adjuster up and down as needed until you hear a click. Center third seat belt The center third seat belt is a 3-point type restraint with 2 buckles. Both seat belt buckles must be correctly located and securely latched for proper operation.
Page 113 1-3. Adjustable components (seats, mirrors, steering wheel) Release method The belt can be completely released when not required, such as when folding down the third seat. Insert the key into the hole on STEP the center seat belt buckle to release the tab (with the hooked end), and allow the belt to retract.
Page 114 1-3. Adjustable components (seats, mirrors, steering wheel) Seat belt comfort guide (outer third seat) If the shoulder belt sits close to a person's neck, use the seat belt comfort guide. Seat belt pretensioners (front seats) The pretensioner helps the seat belt to quickly restrain the occu- pant by retracting the seat belt when the vehicle is subjected to...
Page 115 1-3. Adjustable components (seats, mirrors, steering wheel) Pregnant women Obtain medical advice and wear the seat belt in the proper way. (→P. 84) Women who are pregnant should position the lap belt as low as possible over the hips in the same manner as other occu- pants.
Page 116 Toyota dealer free of charge. I n f o r ma t i o n P r o v i d e d b y :...
Page 117 Each seat belt should be used by one person only. Do not use a seat belt for more than one person at once, including children. Toyota recommends that children be seated in the rear seat and always use a seat belt and/or an appropriate child restraint system.
Page 118 Ensure that the belt and tab are locked and the belt is not twisted. If the seat belt does not function correctly, immediately contact your Toyota dealer. Replace the seat assembly, including the belts, if your vehicle has been involved in a serious accident, even if there is no obvious damage.
Page 119 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION Using a seat belt extender Do not wear the seat belt extender if you can fasten the seat belt without the extender. Do not use the seat belt extender when installing a child restraint system because the belt will not securely hold the child restraint system, increas- ing the risk of death or injury in the event of a collision.
Page 120 1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel The steering wheel can be adjusted to a comfortable position. STEP Hold steering wheel and press the lever down. STEP Adjust to the ideal position by moving the steering wheel hori- zontally and vertically.
Page 121 1-3. Adjustable components (seats, mirrors, steering wheel) Anti-glare inside rear view mirror Glare from the headlights of vehicles behind can be reduced using the following functions. Manual anti-glare inside rear view mirror Normal position Anti-glare position Auto anti-glare inside rear view mirror In automatic mode, sensors are used to detect the headlights of vehicles behind and the reflected light is automatically reduced.
Page 122 1-3. Adjustable components (seats, mirrors, steering wheel) To prevent sensor error (vehicles with auto anti-glare inside rear view mirror) To ensure that the sensors operate prop- erly, do not touch or cover them. CAUTION Caution while driving Do not adjust the position of the mirror while driving. Doing so may lead to mishandling of the vehicle and an accident, resulting in death or serious injury.
Page 123 1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors Mirror angle can be adjusted using the switch. Select a mirror to adjust. STEP Left Right Adjust the mirror. STEP Right Down Left Folding back the mirrors Manual folding type Push backward to fold the mir- rors.
Page 124 1-3. Adjustable components (seats, mirrors, steering wheel) Power folding type Press the switch. Pressing again will extend the mirror. Mirror can be adjusted when The engine switch is in the “ACC” or “ON” position. When the mirrors are fogged up (vehicles with outside rear view mirror defoggers) Turn on the mirror defoggers to defog the mirrors.
Page 125 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION When driving the vehicle Observe the following precautions while driving. Failing to do so may result in loss of control of the vehicle and cause an acci- dent, resulting in death or serious injury. Do not adjust the mirrors while driving.
Page 126 1-4. Opening and closing the windows Power windows The power windows can be opened and closed using the following switches. Type A Closing Opening One-touch opening (driver’s window only) Type B Closing Opening One-touch opening (driver’s window only) One-touch closing (driver’s window only) Pressing the switch in the opposite direction will stop win-...
Page 127 1-4. Opening and closing the windows The power windows can be operated when The engine switch is in the “ON” position. Operating the power windows after turning the engine off The power windows can be operated for approximately 45 seconds after the engine switch is turned to the “ACC”...
Page 128 1-4. Opening and closing the windows Quarter windows The quarter windows can be opened to bring in fresh outside air for additional ventilation. Manual type Pull the handle and swing the window fully out to open. Power type Opening Closing Both the left and right rear quarter windows move.
Page 129 1-4. Opening and closing the windows CAUTION Closing the windows Observe the following precautions. Failing to do so may result in death or serious injury. Check to make sure that all passengers do not have any part of their body in a position where it could be caught when a window is being operated.
Page 130 1-4. Opening and closing the windows Moon roof (if equipped) Use the overhead switches to open, close, and tilt the moon roof up and down. Opening and closing Opening Closing Push the switch in either direc- tion to stop the moon roof part- way.
Page 131 1-4. Opening and closing the windows The moon roof can be operated when The engine switch is in the “ON” position. Operating the moon roof after turning the engine off The moon roof can be operated for approximately 45 seconds after the engine switch is turned to the “ACC”...
Page 132 1-4. Opening and closing the windows CAUTION Opening the moon roof Observe the following precautions. Failing to do so may cause death or serious injury. Do not allow any passengers to put their hands or heads outside the vehi- cle while it is moving. Do not sit on top of the moon roof.
Page 133 1-5. Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap. Before refueling the vehicle Turn the engine off and ensure that all the doors and windows are closed. Opening the fuel tank cap Pull up the fuel filler door STEP opener.
Page 134 1-5. Refueling Closing the fuel tank cap When replacing the fuel tank cap, turn it until a clicking sound is heard. After releasing your hand, the cap will turn slightly to the opposite direction. Fuel type Unleaded gasoline (87 Octane rating [Research Octane Number 91] or higher) Fuel tank capacity (reference) 20.9 gal.
Page 135 This may cause static electricity to build up, resulting in a possible ignition hazard. When replacing the fuel cap Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.
Page 136 1-5. Refueling NOTICE Refueling Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the exhaust systems to operate abnormally or damaging fuel system components or the vehicle's painted surface. I n f o r ma t i o n P r o v i d e d b y :...
Page 137: 1-6. Theft Deterrent System
1-6. Theft deterrent system Engine immobilizer system (if equipped) The vehicle's keys have built-in transponder chips that prevent the engine from starting if the key has not been previously registered in the vehicle's on-board computer. Never leave the keys inside the vehicle when you leave the vehicle. On some models: The indica- tor light flashes after the key has been removed from the...
Page 138 1-6. Theft deterrent system CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTICE To prevent damage to the key Do not modify, remove or disable the engine immobilizer system. If any unauthorized changes or modifications are made, the proper operation of the system cannot be guaranteed.
Page 139 1-6. Theft deterrent system Alarm (if equipped) The system sounds the alarm and flashes the lights when forcible entry is detected. Triggering of the alarm The alarm is triggered in the following situations. l A locked door is unlocked or opened without the key or wire- less remote control.
Page 140 1-6. Theft deterrent system Items to check before locking the vehicle To prevent unexpected triggering of the alarm and vehicle theft, make sure of the following. Nobody is in the vehicle. The windows and moon roof are closed before the alarm is set. No valuables or other personal items are left in the vehicle.
Page 141: Theft Prevention Labels
1-6. Theft deterrent system Theft prevention labels (for U.S.A.) These labels are attached to the vehicle to reduce vehicle theft by facilitating the tracing and recovery of parts from sto- len vehicles. Do not remove under penalty of law. I n f o r ma t i o n P r o v i d e d b y :...
Page 142 1-7. Safety information Correct driving posture Drive in a good posture as follows: Sit upright and well back in the seat. (→P. 56) Adjust the position of the seat forward or backward to ensure the pedals can be reached easily depressed to the extent required.
Page 143 1-7. Safety information CAUTION While driving Do not adjust the position of the driver's seat while driving. Doing so could cause the driver to lose control of the vehicle. Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.
Page 144 1-7. Safety information SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury. Front airbags Driver airbag/front passenger airbag Can help protect the head and chest of the driver and front pas-...
Page 145 1-7. Safety information Airbag system components Curtain shield airbags SRS warning light Side airbags Driver airbag Front passenger airbag Driver’s seat position sen- Side and curtain shield air- bag sensors Driver’s seat belt buckle switch Front airbag sensors “AIR BAG ON” and “AIR Front passenger’s seat belt BAG OFF”...
Page 146 1-7. Safety information The main SRS airbag system components are shown above. The SRS airbag system is controlled by the airbag sensor assembly. The airbag sensor assembly consists of a safing sensor and an airbag sensor. In certain types of severe frontal or side impacts, the SRS airbag sys- tem triggers the airbag inflators.
Page 147 1-7. Safety information Operating conditions (front airbags) The SRS front airbags will deploy if the severity of the frontal impact is above the designed threshold level, comparable to an approximate 15 mph (25 km/h) collision when the vehicle impacts straight into a fixed bar- rier that does not move or deform.
Page 148 1-7. Safety information Conditions under which the SRS airbags may deploy (inflate), other than a collision The SRS front airbags may also deploy if a serious impact occurs to the underside of your vehicle. Some examples are shown in the illustration. Hitting a curb, edge of pavement or hard surface Falling into or jumping over a deep hole...
Page 149 1-7. Safety information Types of collisions that may not deploy the SRS side airbags and cur- tain shield airbags The SRS side airbag and curtain shield airbag system may not activate if the vehicle is subjected to a collision from the side at certain angles, or a colli- sion to the side of the vehicle body other than the passenger compartment.
Page 150 1-7. Safety information When to contact your Toyota dealer In the following cases, contact your Toyota dealer as soon as possible. Do not disconnect the battery cables before contacting your Toyota dealer. Any of the SRS airbags have been inflated.
Page 151 1-7. Safety information CAUTION SRS airbag precautions Observe the following precautions regarding the airbags. Failure to do so may cause death or serious injury. The driver and all passengers in the vehicle must wear their seat belts properly. The SRS airbags are supplemental devices to be used with the seat belts. The SRS driver airbag deploys with considerable force, and can cause death or serious injury especially if the driver is very close to the airbag.
Page 152 An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are the safest for infants and children.
Page 153 1-7. Safety information CAUTION SRS airbag precautions Do not sit on the edge of the seat or lean against the dashboard. Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger. Do not drive the vehicle while the driver or passenger has items resting on their knees.
Page 154 1-7. Safety information CAUTION SRS airbag precautions Do not attach anything to or lean any- thing against areas such as the dash- board or steering wheel pad. These items can become projectiles when SRS driver and front passenger airbags deploy. Do not attach anything to areas such as the door, windshield glass, side door glass, front or side pillars, roof side rail...
Page 155 If the areas where the SRS airbags are stored, such as the steering wheel pad and front and rear pillar garnishes, are damaged or cracked, have them replaced by your Toyota dealer. Modification and disposal of SRS airbag system components Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer.
Page 156 1-7. Safety information Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the front passen- ger seat and activates or deactivates the devices for front passenger. SRS warning light Front passenger's seat belt reminder light “AIR BAG OFF”...
Page 157 1-7. Safety information Conditions and operation of the front passenger occupant classification system Adult* “AIR BAG ON” and “AIR BAG OFF” “AIR BAG indicator lights ON” Indicator/ SRS warning light warning light Front passenger's seat belt reminder Flashing* light Front passenger airbag Side airbag on the front passenger seat Devices Activated...
Page 158 1-7. Safety information Unoccupied “AIR BAG ON” and “AIR BAG OFF” indicator lights illuminated Indicator/ SRS warning light warning light Front passenger's seat belt reminder light Front passenger airbag Deactivated Side airbag on the front passenger seat Devices Curtain shield airbag in the front Activated passenger side Front passenger's seat belt pretensioner...
Page 159 1-7. Safety information *4: Never install a rear-facing child restraint system on the front pas- senger seat. A forward-facing child restraint system should only be installed on the front passenger seat when it is unavoidable. (→P. 136) *5: In case the indicator is not illuminated, consult this manual as for installing the child restraint system properly.
Page 160 1-7. Safety information CAUTION Front passenger occupant classification system precautions Observe the following precautions regarding front passenger occupant clas- sification system. Failure to do so may cause death or serious injury. Wear the seat belt properly. Make sure the front passenger's seat belt tab has not been left inserted into the buckle before someone sits in the front passenger seat.
Page 161 Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately. Child restraint systems installed on the rear seat should not contact the front seatbacks.
Page 162 1-7. Safety information Child restraint systems A child restraint system for a small child or baby must be properly restrained on the seat with the lap portion of the lap/shoulder belt. The laws of all 50 states of U.S.A. and Canada now require the use of child restraint systems.
Page 163 1-7. Safety information Types of child restraints Child restraint systems are classified into the following 3 types according to the age and size of the child. Rear facing ⎯ Infant seat/convertible seat Forward facing ⎯ Convertible seat Booster seat I n f o r ma t i o n P r o v i d e d b y :...
Page 164 In an accident, the child can be crushed against the windshield, or between you and the vehicle's interior. Toyota strongly urges the use of a proper child restraint system that con- forms to the size of the child, installed on the rear seat. According to acci- dent statistics, the child is safer when properly restrained in the rear seat than in the front seat.
Page 165 1-7. Safety information CAUTION Child restraint precautions Do not use the seat belt extender when installing a child restraint system on the front or rear passenger seat. If installing a child restraint system with the seat belt extender connected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or seri- ous injury to the child or other passengers in the event of collision.
Page 166 1-7. Safety information Installing child restraints Follow the child restraint system manufacturer's instructions. Firmly secure child restraints to the rear seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used if your child restraint system is not compatible with the LATCH (Lower Anchors and Tethers for Chil- dren) system.
Page 167: Third Seats
1-7. Safety information Third seats Child restraint LATCH anchors LATCH anchors are provided for right and center seats. (But- tons displaying the location of the anchors are attached to the seats.) Using the seat belts Seat belts equipped with a child restraint locking mecha- nism (ALR/ELR belts except driver’s seat belt)
Page 168 1-7. Safety information Second seats (8-passenger models) Anchor brackets are provided for all second seats. Second seats (7-passenger models) Anchor brackets are provided for both second seats. Third seats Anchor brackets are provided for right and center seats. I n f o r ma t i o n P r o v i d e d b y :...
Page 169 1-7. Safety information Installation with LATCH system (second seat) Outer seats Fold the seatback while pulling STEP the lever. Return the seatback and secure it at the 1st lock posi- tion (most upright position). Adjust the seatback to the 5th lock position.
Page 170 1-7. Safety information Type A STEP LATCH anchors behind the button. Open the cover and confirm the position of the LATCH anchors. STEP Latch the buckles onto the LATCH anchors. STEP If the child restraint has a top tether strap, the top tether strap should be latched onto...
Page 171 1-7. Safety information Type B STEP LATCH anchors behind the button. Open the cover and confirm the position of the LATCH anchors. STEP Latch the hooks of the lower straps onto the LATCH anchors. STEP If the child restraint has a top tether strap, the top tether strap should be latched...
Page 172 1-7. Safety information Installation with LATCH system (third seat) Manual seat Fold the seatback while pulling STEP the lever. Return the seatback and secure it at the 1st lock posi- tion (most upright position). Adjust the seatback to the 11th lock position.
Page 173 1-7. Safety information Type A STEP Widen the gap between the seat cushion and seatback slightly confirm the position of the LATCH anchors near the button on the seatback. STEP Latch the buckles onto the LATCH anchors. STEP If the child restraint has a top tether strap, the top tether strap should be latched...
Page 174 1-7. Safety information Type B STEP Widen the gap between the seat cushion and seatback slightly confirm the position of the LATCH anchors near the button on the seatback. STEP Latch the hooks of the lower straps onto the LATCH anchors. STEP If the child restraint has a top tether strap, the top...
Page 175 1-7. Safety information Run the seat belt through the STEP child seat and insert the plate into the buckle. Make sure that the belt is not twisted. Fully extend the shoulder belt STEP and then allow it to retract slightly in order to activate the ALR lock mode.
Page 176 1-7. Safety information Run the seat belt through the STEP child seat and insert the plate into the buckle. Make sure that the belt is not twisted. Fully extend the shoulder strap STEP and then allow it to retract slightly into the ALR lock mode. Lock mode allows the seat belt to retract only.
Page 177 1-7. Safety information Booster seat Place the booster seat on the STEP seat facing the front of the vehi- cle. Sit the child in the booster seat. STEP Fit the seat belt to the booster seat according to the manufac- turer's instructions and insert the plate into the buckle.
Page 178 1-7. Safety information Child restraint systems with a top tether strap (second seat) Secure the child restraint using STEP the seat belt or LATCH anchors. Remove the head restraint. Latch the hook onto the anchor STEP bracket and tighten the top tether strap.
Page 179 1-7. Safety information Child restraint systems with a top tether strap (third seat) Secure the child restraint using STEP the seat belt or LATCH anchors. Remove and safely stow the head restraint. Latch the hook onto the anchor STEP bracket and tighten the top tether strap.
Page 180 1-7. Safety information CAUTION When installing a booster seat Do not fully extend the shoulder belt to prevent the belt from going to ALR lock mode: (→P. 87) ALR mode causes the belt to tighten only which could cause injury or dis- comfort to the child.
Page 181 1-7. Safety information CAUTION When installing a child restraint system When installing a child restraint system in the third center seat, adjust both seatbacks at the same angle. Otherwise, the child restraint system cannot be securely restrained and this may cause death or serious injuries in a collision.
Page 182 1-7. Safety information CAUTION To correctly attach a child restraint system to the anchors When using the LATCH anchors, be sure that there are no foreign objects around the anchors and that the seat belt is not caught behind the child restraint.
Page 183 1-7. Safety information I n f o r ma t i o n P r o v i d e d b y :...
Page 184 2-1. Driving procedures Driving the vehicle The following procedures should be observed to ensure safe driv- ing. Starting the engine →P. 167 Driving STEP With the brake pedal depressed, shift the shift lever to D. (→P. 170) STEP Release the parking brake. (→P.
Page 185 Breaking in your new Toyota To extend the life of the vehicle, the following precautions are recommended...
Page 186 Your vehicle has a drum-in-disc type parking brake system. This type of brake system needs bedding-down of the brake shoes periodically or when- ever the parking brake shoes and/or drum are replaced. Have your Toyota dealer perform the bedding down.
Page 187 Large amounts of exhaust in the vehi- cle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immediately. Do not under any circumstances shift the shift lever to P or R while the vehicle is moving.
Page 188 2-1. Driving procedures CAUTION AWD models: Do not drive across a river or through other bodies of water. This may cause electric/electronic components to short circuit, damage the engine or cause other serious damage to the vehicle. Do not drive in excess of the speed limit. Even if the legal speed limit per- mits it, do not drive over 85 mph (140 km/h) unless your vehicle has high- speed capability tires.
Page 189 The exhaust should be checked occasionally. If there is a hole or crack caused by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer. Failure to do so may allow exhaust gases to enter the vehicle, resulting in death or a serious health hazard.
Page 190 2-1. Driving procedures CAUTION When taking a nap in the vehicle Always turn the engine off. Otherwise, you may accidentally move the shift lever or depress the accelerator pedal, which could cause an accident or fire due to engine overheating. Additionally, if the vehicle is parked in a poorly ventilated area, exhaust gases may collect and enter the vehicle, leading to death or a serious health hazard.
Page 191 If you hear a squealing or scraping noise (brake pad wear limit indica- tors) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. Rotor damage can result if the pads are not replaced when needed.
Page 192 Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following. Brake function Changes in quantity and quality of oil and fluid used for the engine, tran- saxle, transfer (AWD models), differential, etc.
Page 193 2-1. Driving procedures Engine (ignition) switch Starting the engine STEP Check that the parking brake is set. STEP Check that the shift lever is set in P. STEP Sit in the driver’s seat and firmly depress the brake pedal. STEP Turn the engine switch to the “START”...
Page 194 2-1. Driving procedures Steering lock release When starting the engine, the engine switch may seem stuck in the “LOCK” position. To free it, turn the key while turn- ing the steering wheel slightly in either direction. If the engine does not start (vehicles with engine immobilizer system) The engine immobilizer system may not have been deactivated.
Page 195 2-1. Driving procedures NOTICE To prevent battery discharge Do not leave the key in the “ACC” or “ON” position for long periods if the engine is not running. When starting the engine Do not race a cold engine. If the engine becomes difficult to start or stalls frequently, have the engine checked immediately.
Page 196 2-1. Driving procedures Automatic transmission Select a shift position appropriate for the driving conditions. Shifting the shift lever While the engine switch is in the “ON” position, depress the brake pedal and move the shift lever. Shift position uses Shift position Function Parking the vehicle or starting the engine Reversing...
Page 197 2-1. Driving procedures Downshifting restrictions The shift lever cannot be downshifted if the following speeds are exceeded. 2WD models mph (km/h) Downshifting Maximum speed 4→3 100 (162) 3→2 64 (104) 2→L 36 (58) AWD models mph (km/h) Downshifting Maximum speed 4→3 95 (154) 3→2...
Page 198 2-1. Driving procedures Turn signal lever Right turn Left turn Move and hold the lever partway to signal a lane change. The right hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change.
Page 199 2-1. Driving procedures Parking brake Sets the parking brake* (Depressing the pedal again releases the parking brake.) U.S.A. Canada *: Fully depress the parking brake pedal with your left foot while depressing the brake pedal with your right foot. NOTICE Before driving Fully release the parking brake.
Page 200 2-2. Instrument cluster and information display Gauges and meters Optitron type meters Non-Optitron type meters Optitron type meters only ⎯ The following gauges, meters and dis- plays illuminate when the engine switch is in the “ON” position. Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed.
Page 201 2-2. Instrument cluster and information display Fuel gauge Displays the quantity of fuel remaining in the tank. Engine coolant temperature gauge Displays the engine coolant temperature. Dynamic laser cruise control display (if equipped) →P. 197 Odometer/trip meter/instrument panel light control and trip meter reset button Switches between odometer and trip meter displays.
Page 202 2-2. Instrument cluster and information display Instrument panel light control The brightness of the instrument panel lights can be adjusted. Darker Brighter Optitron type meters only: When the headlight switch is turned on, the brightness will be reduced slightly unless the control button is turned fully clockwise.
Page 203 2-2. Instrument cluster and information display Indicators and warning lights The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems. Instrument cluster Optitron type meters Non-Optitron type meters I n f o r ma t i o n P r o v i d e d b y :...
Page 204 2-2. Instrument cluster and information display Center panel I n f o r ma t i o n P r o v i d e d b y :...
Page 205 There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer for details.
Page 206 There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer for details.
Page 207 2-2. Instrument cluster and information display Trip information display (if equipped) The trip information display presents the driver with a variety of driv- ing-related data, including the current outside temperature. Trip information (→P. 182) Displays outside temperature, fuel consumption and cruising range.
Page 208 2-2. Instrument cluster and information display Trip information Push the “MODE” button to dis- play trip information. Display items can be switched by pressing the “MODE” button. Outside temperature Displays the outside temperature. The temperature range that can be displayed is from -40°F (-40°C) to 140°F (60°C).
Page 209 2-2. Instrument cluster and information display Cruising range Displays the estimated maximum distance that can be driven with the quantity of fuel remaining. • This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that displayed.
Page 210 2-2. Instrument cluster and information display Outside temperature display In the following situations, the correct outside temperature may not be dis- played, or the display may take longer than normal to change. When stopped, or driving at low speeds (less than 12 mph [20 km/h]) When the outside temperature has changed suddenly (at the entrance/ exit of a garage, tunnel, etc.) I n f o r ma t i o n P r o v i d e d b y :...
Page 211 2-3. Operating the lights and wipers Headlight switch The headlights can be operated manually or automatically. The side marker, park- ing, tail, license plate and instrument panel lights turn on. The headlights and all lights listed above turn The headlights, side marker, parking, tail, (if equipped) license...
Page 212 2-3. Operating the lights and wipers Turning on the high beam headlights With the headlights on, push the lever forward to turn on the high beams. Pull the lever back to the center position to turn the high beams off. Pull the lever toward you to turn on the high beams.
Page 213 2-3. Operating the lights and wipers Manual headlight leveling dial (vehicles with discharge headlights) The level of the headlights can be adjusted according to the number of passengers and the loading condition of the vehicle. Raises the level of the head- lights Lowers the level of the head- lights...
Page 214 To turn the lights on again, turn the engine switch to the “ON” position, or turn the light switch off once and then back to the position. Customization that can be configured at Toyota dealer Settings (e.g. light sensor sensitivity) can be changed. (Customizable features →P. 565)
Page 215 2-3. Operating the lights and wipers NOTICE To prevent battery discharge Do not leave the lights on longer than necessary when the engine is not run- ning. I n f o r ma t i o n P r o v i d e d b y :...
Page 216: Fog Light Switch
2-3. Operating the lights and wipers Fog light switch (if equipped) The fog lights improve visibility in difficult driving conditions, such as in rain or fog. They can be turned on only when the headlights are on low beam. To turn the front fog lights To turn the front fog lights I n f o r ma t i o n P r o v i d e d b y :...
Page 217 2-3. Operating the lights and wipers Windshield wipers and washer Wiper intervals can be adjusted for intermittent operation (when intermittent wiper operation is selected). Intermittent windshield wiper operation Low speed windshield wiper operation High speed windshield wiper operation Temporary operation Intermittent windshield wiper interval adjustment...
Page 218 2-3. Operating the lights and wipers Washer/wiper dual operation Wipers operate automatically. The windshield wipers and washer can be operated when The engine switch is in the “ON” position. If no windshield washer fluid sprays Check that the washer nozzles are not blocked if there is washer fluid in the windshield washer fluid reservoir.
Page 219 2-3. Operating the lights and wipers Rear window wiper and washer Intermittent window wiper operation Normal window wiper oper- ation Washer/wiper dual opera- tion Washer/wiper dual opera- tion Wiper operates automatically. The rear window wiper and washer can be operated when The engine switch is in the “ON”...
Page 220 2-5. Driving information Cargo and luggage Take notice of the following information about storage precau- tions, cargo capacity and load. l Stow cargo and luggage in the luggage compartment whenever possible. Be sure all items are secured in place. l Be careful to keep the vehicle level. Placing the weight as far for- ward as possible helps maintain vehicle balance.
Page 221 2-5. Driving information Slide the cross rails to the appro- STEP priate position for loading lug- gage turn knobs clockwise to tighten the cross rails securely. Capacity and distribution Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) - (Total weight of occupants) Steps for Determining Correct Load Limit ⎯...
Page 222: Total Load Capacity
2-5. Driving information (6) If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (→P. 542) Example on your vehicle Cargo capacity Total load capacity...
Page 223 2-5. Driving information Seating configuration variation Cargo capacity Weight of the removed second seat If removing the second seats, it is possible to load extra cargo equal to the weight of the removed seats. (Cargo capacity) = (Total load capacity) - (Total weight of occupants) + (Weight of the removed second seats) Second seats weight: 7-passenger models ⎯...
Page 224: Storage Precautions
2-5. Driving information CAUTION Storage precautions Do not stack anything in the luggage compartment higher than the seatbacks. Such items may be thrown about and possibly injure people in the vehicle during sudden braking or in an accident. Do not place items in or on the following locations: •...
Page 225 2-5. Driving information CAUTION Roof luggage carrier precautions When you load cargo on the roof luggage carrier, observe the following: Place the cargo so that its weight is distributed evenly between the front and rear axles. If loading long or wide cargo, never exceed the vehicle overall length or width.
Page 226 2-5. Driving information Vehicle load limits Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity. Total load capacity: (→P. 542) Total load capacity means the combined weight of occupants, cargo and luggage. Seating capacity: 7-passenger models Total 7 (Front 2, Rear 5) 8-passenger models Total 8 (Front 2, Rear 6)
Page 227 2-5. Driving information Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. Pre-winter preparations l Use fluids that are appropriate to the prevailing outside tem- peratures.
Page 228 2-5. Driving information When driving the vehicle Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions. When parking the vehicle Park the vehicle and move the shift lever to P without setting the parking brake. The parking brake may freeze up, preventing it from being released.
Page 229: Snow Tires
NOTICE Repairing or replacing snow tires Request repairs of and obtain replacement snow tires from Toyota dealers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.
Page 230 For your safety and the safety of others, do not overload the vehicle or trailer. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. Weight limits Confirm that the total trailer weight, gross vehicle weight, gross axle weight and trailer tongue load are all within the limits.
Page 231 Tongue load Towing a trailer Contact your Toyota dealer for further information about additional requirements such as a towing kit, etc. I n f o r ma t i o n P r o v i d e d b y :...
Page 232 Break-in schedule Toyota recommends that you do not use a new vehicle or a vehicle with any new power train components (engine, transmission, differential, wheel bear- ings, etc.) to tow a trailer for the first 500 miles (800 km) of driving.
Page 233 When towing a trailer If the gross trailer weight exceeds 1000 lb. (453 kg), trailer brakes are required. Toyota recommends trailers with brakes that conform to all appli- cable federal and state/provincial regulations. Never tap into your vehicle's hydraulic system, as this will lower the vehi- cle's braking effectiveness.
Page 234 NOTICE When installing a trailer hitch Use only the position recommended by your Toyota dealer. Do not install the trailer hitch on the bumper; this may cause body damage. Do not use axle-mounted hitches, as they can cause damage to the axle housing, wheel bearings, wheels or tires.
Page 235 2-5. Driving information l Reversing with a trailer attached is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to right.
Page 236 2-5. Driving information l Due to the added load of the trailer, your vehicle's engine may overheat on hot days (at temperatures over 85°F [30°C]) when driving up a long or steep grade. If the engine coolant temperature gauge indicates overheating, immediately turn off the air condition- ing (if in use), pull your vehicle off the road and stop in a safe spot.
Page 237 2-5. Driving information CAUTION To avoid an accident Do not exceed 45 mph (72 km/h) or posted towing speed limit, whichever is lower. As instability (swaying) of the towing vehicle-trailer combination increases as speed increases, exceeding 45 mph (72 km/h) may cause loss of control.
Page 238 2-5. Driving information Dinghy towing Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home. NOTICE To avoid serious damage to your vehicle Do not tow your vehicle with four wheels on the ground. I n f o r ma t i o n P r o v i d e d b y :...
Page 239: Sun Visors
3-7. Other interior features Sun visors Forward position: Flip down. Side position: Flip down, unhook, and swing to the side. I n f o r ma t i o n P r o v i d e d b y :...
Page 240 3-7. Other interior features Vanity mirrors Flip down. Open the cover. The light turns on when the cover is opened. I n f o r ma t i o n P r o v i d e d b y :...
Page 241 3-7. Other interior features Clock With a manual air conditioning system Adjusts the hours. Adjusts the minutes. With an automatic air conditioning system Adjusts the hours. Adjusts the minutes. The clock is displayed when The engine switch is in the “ACC” or “ON” position. When disconnecting and reconnecting battery terminals The time display will automatically be set to 1:00.
Page 242 3-7. Other interior features Conversation mirror The conversation mirror can provide the driver and the front passen- ger with a view of the rear seat area without the need to turn around. Push the tab and flip down the STEP lid.
Page 243 3-7. Other interior features Power outlets The following power outlets can be used for: 12 V: Accessories that use a combined total of less than 120 W (10 A at 12 V). 115 VAC: Accessories that use a combined total of less than 100 12 V Center panel Luggage compartment...
Page 244 3-7. Other interior features 115 VAC (if equipped) Main switch To use the power outlet, turn on the main switch. The indicator light comes on. Power outlet socket (beside third seat) Power outlet socket (luggage compartment) I n f o r ma t i o n P r o v i d e d b y :...
Page 245 3-7. Other interior features The power outlet can be used when 12 V The engine switch is in the “ACC” or “ON” position. 115 VAC The engine switch is in the “ON” position. NOTICE To avoid damaging the power outlet Close the power outlet lid when the power outlet is not in use.
Page 246 3-7. Other interior features Seat heaters (if equipped) Front passenger’s seat The indicator light comes on. Adjusts the seat tempera- ture The further you move the dial upward, the warmer the seat Driver’s seat becomes. The seat heaters can be used when The engine switch is in the “ON”...
Page 247 3-7. Other interior features NOTICE To prevent seat heater damage Do not put unevenly weighted objects on the seat and do not stick sharp objects (needles, nails, etc.) into the seat. To prevent battery discharge Turn the switches off when the engine is not running. I n f o r ma t i o n P r o v i d e d b y :...
Page 248 3-7. Other interior features Armrests Front seat Pull the armrest down for use. Second seat (if equipped) Pull the armrest down for use. NOTICE To prevent damage to the armrest Do not place too much strain on the armrest. I n f o r ma t i o n P r o v i d e d b y :...
Page 249 3-7. Other interior features Rear side sunshades (if equipped) Rear door window Pull the tab up. Secure the sunshade using the hooks. To retract the sunshade, pull the tab up slightly to unhook the sunshade, and lower the sunshade slowly. Rear quarter window Pull the tab up.
Page 250 3-7. Other interior features Grocery bag hooks The hooks are designed to hang things like a grocery bag. Type A (instrument panel) Pull the hook down. Type B (front seatback) Type C (manual third seat) I n f o r ma t i o n P r o v i d e d b y :...
Page 251 3-7. Other interior features Type C (power third seat) Type D (luggage compartment) Pull the hook up. CAUTION When not in use (Type A and D) Keep the grocery bag hook stowed. Injuries may result in the event of an accident or sudden braking. NOTICE Grocery bag hook weight capacity (Type A, B and C) Do not hang any object heavier than 8.8 lb.
Page 252 3-7. Other interior features Coat hooks To use the coat hook, pull it down. CAUTION Items that must not be hung on the hook Do not hang a coat hanger or other hard or sharp objects on the hook. If the SRS curtain shield airbags deploy, these items may become projectiles that cause death or serious injury.
Page 253 3-7. Other interior features Seatback tables Following seatbacks can be used as a temporary table only when the vehicle is stopped. Front passenger’s seatback table (if equipped) Fold down the seatback. (→P. 56) Second outside seatback table Fold down the seatback. (→P.
Page 254 3-7. Other interior features CAUTION Caution while driving Observe the following precautions to avoid death or serious injury. Do not set up the seatback table. Do not sit on or place anything on the seatback table. NOTICE To prevent damage to the seatback table Do not put heavy loads on the table.
Page 255: Front Seat Side Table
3-7. Other interior features Front seat side table (if equipped) Front seat side table can be used as a temporary table only when the vehicle is stopped. Raise the table if it is folded down. Folding down the front seat side table Pull up the lever and push against the driver's seat side.
Page 256 3-7. Other interior features CAUTION Caution while driving Do not place anything on the front seat side table to avoid death or serious injury. When not in use Keep the front seat side table folded down and securely locked. Injuries may result in the event of an accident or sudden braking. NOTICE To prevent damage to the front seat side table Do not put heavy loads on the table.
Page 257 3-7. Other interior features Floor mat Securely place a mat that matches the size of the space on the car- pet. Secure the driver's floor mat using the hooks provided. CAUTION When inserting the floor mat Observe the following precautions. Failure to do so may result in the floor mat slipping and interfering with the movement of the pedals during driving, resulting in an accident.
Page 258 3-7. Other interior features Luggage compartment features Cargo hooks Cargo hooks are provided for securing loose items. Cargo net hooks Pattern 1 Pattern 2 I n f o r ma t i o n P r o v i d e d b y :...
Page 259 3-7. Other interior features Pattern 3 Pattern 4 Storage box (if equipped) I n f o r ma t i o n P r o v i d e d b y :...
Page 260 3-7. Other interior features CAUTION When the cargo hooks are not in use To avoid injury, always return the cargo hooks to their positions when they are not in use. NOTICE To prevent damage to the cargo net hooks Avoid hanging things other than a cargo net on them. I n f o r ma t i o n P r o v i d e d b y :...
Page 261 3-7. Other interior features Garage door opener (if equipped) The garage door opener can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, secu- rity systems, and other devices. ® The garage door opener (HomeLink Universal Transceiver) is manufac- ®...
Page 262 3-7. Other interior features Press and hold down one of the STEP ® buttons on the HomeLink the button on the transmitter. When the indicator light on the ® HomeLink changes from a slow to a rapid flash after 20 seconds, you can release both buttons.
Page 263 3-7. Other interior features Programming a Rolling Code system (for U.S.A. owners) If your device is Rolling Code equipped, follow the steps under the ® heading “Programming the HomeLink ” before proceeding with the steps listed below. STEP Locate the training button on the ceiling mounted garage door opener motor.
Page 264 ® the remaining HomeLink buttons. Programming other devices To program other devices such as home security systems, home door locks or lighting, contact your authorized Toyota dealer for assistance. Reprogramming a button ® The individual HomeLink buttons cannot be erased but can be reprogrammed.
Page 265 3-7. Other interior features Before programming Install a new battery in the transmitter. The battery side of the transmitter must be pointed away from the ® HomeLink Certification for the garage door opener This device complies with Part 15 of the FCC Rules and with RSS-210 of the IC Rules.
Page 266 3-7. Other interior features Garage door opener box (if equipped) The box is designed to store a garage door opener transmitter. Setting the transmitter Push the button and flip down STEP the lid. Remove the hook-and-loop STEP fastener. Remove the paper strip cover- STEP ing the adhesive on backside of loop and adhere loop to...
Page 267 3-7. Other interior features Place the transmitter with the STEP fastener facing inside of box into the box. Remove spacers from the STEP center panel. Place one spacer on the pin that would be below the trans- mitter button when the cover is closed.
Page 268 3-7. Other interior features When the spacer does not contact your transmitter button Check to see if the spacer is on the correct pin. If the spacer is on the correct pin, attach another spacer on top of the original spacer. Recheck transmitter opera-...
Page 269 3-7. Other interior features Compass (if equipped) The compass on the trip information display indicates the direction in which the vehicle is heading. Operation Direction display “E/M” button “MODE” button Displays and directions Display Direction North Northeast East Southeast South Southwest West Northwest...
Page 270 3-7. Other interior features Calibrating the compass The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies according to the geographic position of the vehicle. If you cross over a map boundary shown in illustration, the compass will deviate.
Page 271 3-7. Other interior features STEP Press the “E/M” button, and referring to the map above, select the number of the zone where you are. If the direction is displayed several seconds after adjustment, the calibration is complete. Circling calibration When the direction display may not change after a turn, the com- pass needs to be calibrated.
Page 272 3-7. Other interior features Conditions unfavorable to correct operation The compass may not show the correct direction in the following conditions: The vehicle is stopped immediately after turning. The vehicle is on an inclined surface. The vehicle is in a place where the earth's magnetic field is subject to interference by artificial magnetic fields (underground car park/parking lot, under a steel tower, between buildings, roof car park/parking lot, near an intersection, near a large vehicle, etc.).
Page 273 4-1. Maintenance and care Cleaning and protecting the vehicle exterior Perform the following to protect the vehicle and maintain it in prime condition. l Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust.
Page 274 4-1. Maintenance and care Aluminum wheels Remove any dirt immediately using a neutral detergent. Do not use hard brushes or abrasive cleaners. Do not use strong or harsh chemical cleaners. Use the same mild detergent and wax as used on the paint. Bumpers and side moldings Do not scrub with abrasive cleaners.
Page 275 Do not use organic cleaners such as benzene or gasoline. If the windshield washer nozzle or rear window washer nozzle becomes blocked Contact your Toyota dealer. Do not try to clear it with a pin or other object. This may damage the nozzle. Cleaning the exterior lights Wash carefully.
Page 276 4-1. Maintenance and care Cleaning and protecting the vehicle interior The following procedures will help protect your vehicle's interior and keep it in top condition: Protecting the vehicle interior Remove dirt and dust using a vacuum cleaner. Wipe dirty sur- faces with a cloth dampened with lukewarm water.
Page 277 (if equipped). Caring for leather areas Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle's interior. Shampooing the carpets There are several commercial foaming-type cleaners available.
Page 278 4-1. Maintenance and care NOTICE Cleaning detergents Do not use organic substances such as benzene or gasoline, acidic or alka- line solutions, dye, bleach or other detergent. Doing so may discolor the vehicle interior or cause streaks or damage to painted surfaces. Preventing damage to leather surfaces Observe the following precautions to avoid damage to and deterioration of leather surfaces.
Page 279 It is recommended that genuine Toyota parts be used for repair to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than a Toyota dealer performs repairs, confirm the war- ranty coverage.
Page 280 4-2. Maintenance Allow inspection and repairs to be performed by a Toyota dealer Toyota technicians are well-trained specialists and are kept up to date with the latest service information. They are well informed about the operations of all systems on your vehicle.
Page 281 “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice. Engine compartment Items...
Page 282 4-2. Maintenance Vehicle interior Items Check points • Moves smoothly (without uneven Accelerator pedal pedal effort or catching)? • Can the vehicle be held securely Automatic transmission “Park” on an incline with the shift lever in mechanism • Moves smoothly? •...
Page 283: Inflation Pressure
4-2. Maintenance Vehicle exterior Items Check points Doors • Operate smoothly? Engine hood • The lock system works properly? • Is there any leakage after park- Fluid leaks ing? • Inflation pressure is correct? • Tire surfaces not worn or dam- aged? Tires •...
Page 284 The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/ M test and may need to be repaired. Contact your Toyota dealer to service the vehicle. Your vehicle may not pass the I/M test:...
Page 285 Brake fluid level (→P. 446) • Rag or paper towel • Funnel (used only for adding brake fluid) • “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non-silicate, non- amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology.
Page 286 4-3. Do-it-yourself maintenance Items Parts and tools • Fuse with same amperage rating Fuses (→P. 474) as original • Bulb with same number and watt- age rating as original Light bulbs (→P. 486) • Phillips-head screwdriver • Flathead screwdriver • Wrench •...
Page 287 4-3. Do-it-yourself maintenance CAUTION The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury, observe the following precautions. When working on the engine compartment Keep hands, clothing, and tools away from the moving fan and engine drive belt.
Page 288 4-3. Do-it-yourself maintenance NOTICE If you remove the air cleaner Driving with the air cleaner removed may cause excessive engine wear due to dirt in the air. Also a backfire could cause a fire in the engine compart- ment. I n f o r ma t i o n P r o v i d e d b y :...
Page 289 4-3. Do-it-yourself maintenance Hood Release the lock from the inside of the vehicle to open the hood. Pull the hood release lever. STEP The hood will pop up slightly. Lift the auxiliary catch lever STEP and lift the hood. Hold the hood open by insert- STEP ing the supporting rod into the slot.
Page 290 4-3. Do-it-yourself maintenance CAUTION Pre-driving check Check that the hood is fully closed and locked. If the hood is not locked properly, it may open while the vehicle is in motion and cause an accident, which may result in death or serious injury. After installing the support rod into the slot Make sure the rod supports the hood securely from falling down on to your head or body.
Page 291 4-3. Do-it-yourself maintenance Positioning a floor jack When raising your vehicle with a floor jack, position the jack cor- rectly. Improper placement may damage your vehicle or cause injury. Front Rear 2WD models AWD models I n f o r ma t i o n P r o v i d e d b y :...
Page 292 4-3. Do-it-yourself maintenance CAUTION When raising your vehicle Make sure to observe the following to reduce the possibility of death or seri- ous injury. Lift up the vehicle using a floor jack such as the one shown in the illustra- tion.
Page 293 4-3. Do-it-yourself maintenance Engine compartment Power steering fluid reservoir Engine coolant reservoir (→P. 448) (→P. 444) Windshield and rear window Brake fluid reservoir washer fluid tank (→P. 453) (→P. 446) Engine oil filler cap Fuse box (→P. 474) (→P. 440) Battery (→P.
Page 294 4-3. Do-it-yourself maintenance Engine oil With the engine at operating temperature and turned off, check the oil level on the dipstick. Checking the engine oil STEP Park the vehicle on level ground. After turning off the engine, wait a few minutes for the oil to drain back into the bottom of the engine.
Page 295 4-3. Do-it-yourself maintenance Adding engine oil If the oil level is below or near the low level mark, add engine oil of the same type as already in the engine. Make sure to check the oil type and prepare the items needed before adding oil.
Page 296 4-3. Do-it-yourself maintenance Recommended viscosity SAE 5W-30 is the best choice for good fuel economy, and good starting in cold weather. If SAE 5W-30 oil is not available, SAE 10W-30 oil may be used. However, it should be replaced Outside temperature with SAE 5W-30 at the next oil change.
Page 297 Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal.
Page 298 4-3. Do-it-yourself maintenance NOTICE To prevent serious engine damage Check the oil level on a regular basis. When replacing the engine oil Be careful not to spill engine oil on the vehicle components. Avoid overfilling, as the engine could be damaged. Check the oil level on the dipstick every time you refill the vehicle.
Page 299 Visually check the radiator, hoses, engine coolant reservoir cap, radiator cap, drain cock and water pump. If you cannot find a leak, have your Toyota dealer test the cap and check for leaks in the cooling system. I n f o r ma t i o n P r o v i d e d b y :...
Page 300 4-3. Do-it-yourself maintenance Coolant selection Only use “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology. U.S.A.: “Toyota Super Long Life Coolant” is a mixture of 50% coolant and 50% deionized water.
Page 301 Check the radiator and condenser, and clear any foreign objects. If either of the above parts are extremely dirty or you are not sure of their condition, have your vehicle checked by your Toyota dealer. CAUTION When the engine is hot Do not touch the radiator or condenser as they may be hot and may cause burns.
Page 302 4-3. Do-it-yourself maintenance Adding fluid Make sure to check the fluid type and prepare the necessary items. Fluid type FMVSS No.116 DOT 3 or SAE J1703 brake fluid Items Clean funnel Brake fluid can absorb moisture from the air Excess moisture in the fluid can cause a dangerous loss of braking effi- ciency.
Page 303 4-3. Do-it-yourself maintenance Power steering fluid Fluid level The fluid level should be within the appropriate range. Full (when cold) Add fluid (when cold) Full (when hot) Add fluid (when hot) Hot: Vehicle has been driven around 50 mph (80 km/h) for 20 minutes, or slightly longer in cold temperatures.
Page 304 4-3. Do-it-yourself maintenance CAUTION Checking the fluid level Take care, as the reservoir may be hot. NOTICE When adding fluid Avoid overfilling, or the power steering may be damaged. After replacing the reservoir cap Check the steering box case, vane pump and hose connections for leaks or damage.
Page 305 Checking battery condition Check the battery condition using the indicator color. Type A Green: Good condition Dark: Charging is necessary. Have the vehicle inspected by your Toyota dealer. Clear or light yellow: Not working properly. Have the battery checked your Toyota dealer.
Page 306 4-3. Do-it-yourself maintenance Before recharging When recharging, the battery produces hydrogen gas which is flammable and explosive. Therefore, before recharging: If recharging with the battery installed on the vehicle, be sure to discon- nect the ground cable. Make sure the power switch on the charger is off when connecting and disconnecting the charger cables to the battery.
Page 307 4-3. Do-it-yourself maintenance CAUTION Chemicals in the battery A battery contains poisonous and corrosive sulfuric acid and may produce hydrogen gas which is flammable and explosive. To reduce the risk of death or serious injury, take the following precautions while working on or near the battery: Do not cause sparks by touching the battery terminals with tools.
Page 308 4-3. Do-it-yourself maintenance NOTICE When recharging the battery Never recharge the battery while the engine is running. Also, be sure all accessories are turned off. Washer fluid Add washer fluid in the following situations. l Any washer does not work. l The low washer fluid warning light comes on.
Page 309 The tire pressure warning system Your Toyota is equipped with a tire pressure warning system that uses tire pressure warning valves and transmitters to detect low tire inflation pressure before serious problems arise. (→P. 507) Vehicles with compact spare tire: The compact spare tire is not equipped with the tire pressure warning valve and transmitters.
Page 310 ID codes must be registered in the tire pressure warning computer and tire pressure warning system must be initialized. Have tire pressure warning valve and transmitter ID codes registered by your Toyota dealer. (→P. 456) Initializing the tire pressure warning system...
Page 311 ID code of tire pressure warning valve and transmitter. Have the ID code registered by your Toyota dealer. I n f o r ma t i o n P r o v i d e d b y :...
Page 312: Tire Inflation Pressure
A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage If you are not sure, consult with your Toyota dealer. Replacing tires and wheels If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly.
Page 313 4-3. Do-it-yourself maintenance Tire types 1 Summer tires Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads.
Page 314 If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer. When operating the tire pressure warning reset switch, the tire pres- sure warning light does not flash 3 times.
Page 315: Tire Pressure Warning System
4-3. Do-it-yourself maintenance Tire pressure warning system certification MODEL/FCC IDs: Transmitter: GQ4-32T Receiver: GQ4-37R IC (Canada) IDs: Transmitter: 1470A-13T Receiver: 1470A-9R For vehicles sold in the U.S.A. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 316 Do not mix tires of different makes, models, tread patterns or tread- wear. Do not use tire sizes other than those recommended by Toyota. Do not mix radial, bias-belted, or bias-ply tires. Do not mix summer, all season and snow tires.
Page 317 When removing or fitting the wheels, tires or the tire pressure warning valve and transmitter, contact your Toyota dealer as the tire pressure warning valve and transmitter may be damaged if not handled correctly. To avoid damaging the tire pressure warning valves and transmit- ters Do not use liquid sealants on flat tires.
Page 318 4-3. Do-it-yourself maintenance Tire inflation pressure Tire inflation pressure The recommended cold tire inflation pressure and tire size is dis- played on the tire and loading information label. (→ P. 548 I n f o r ma t i o n P r o v i d e d b y :...
Page 319 4-3. Do-it-yourself maintenance Inspection and adjustment procedure Tire valve Tire pressure gauge STEP Remove the tire valve cap. STEP Press the tip of the tire pressure gauge onto the tire valve. STEP Read the pressure using the graduations of the gauge. STEP If the tire inflation pressure is not within the recommended levels, adjust the pressure.
Page 320 Reduced driving comfort and tire life Reduced safety Damage to the drive train If a tire needs frequent refilling, have it checked by your Toyota dealer. Instructions for checking tire inflation pressure When checking tire inflation pressure, observe the following: Check only when the tires are cold.
Page 321 4-3. Do-it-yourself maintenance CAUTION Proper inflation is critical to save tire performance Keep your tires properly inflated. Otherwise, the following conditions may occur and result in an accident causing death or serious injury. Excessive wear Uneven wear Poor handling Possibility of blowouts resulting from overheated tires Poor sealing of the tire bead Wheel deformation and/or tire separation A greater possibility of tire damage from road hazards...
Page 322 Used wheels l Bent wheels that have been straightened Aluminum wheel precautions l Use only Toyota wheel nuts and wrenches designed for use with your aluminum wheels. l When rotating, repairing or changing your tires, check that the wheel nuts are still tight after driving 1000 miles (1600 km).
Page 323 Because tire repair or replacement may affect the tire pressure warning valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer.
Page 324 4-3. Do-it-yourself maintenance Air conditioning filter The air conditioning filter must be cleaned or changed regularly to maintain air conditioning efficiency. Removal method STEP Turn the engine switch to the “LOCK” position. Open the glove box. Slide off STEP the damper. Push in each side of the glove STEP box to disconnect the claws.
Page 325 2 minutes at 72 psi (500 kPa, 5.0 kgf/cm bar). If it is not available, have the filter cleaned by your Toyota dealer. Replacement method Install a new filter to the filter case.
Page 326 4-3. Do-it-yourself maintenance Checking interval Inspect, clean and replace the air conditioning filter according to the mainte- nance schedule. In dusty areas or areas with heavy traffic flow, more fre- quent cleaning or early replacement may be required. (For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide”...
Page 327 4-3. Do-it-yourself maintenance Wireless remote control battery Replace the battery with a new one if it is discharged. You will need the following: Lithium battery (CR2032) Replacing the battery Remove the cover using a STEP coin protected with tape etc. Remove the discharged trans- STEP mitter battery.
Page 328 The wireless remote control will not function properly. The operational range is reduced. Use a CR2032 lithium battery Batteries can be purchased at your Toyota dealer, jewelers, or camera stores. Replace only with the same or equivalent type recommended by your Toyota dealer.
Page 329 4-3. Do-it-yourself maintenance Checking and replacing fuses If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. STEP Turn the engine switch to the “LOCK” position. STEP The fuses are located in the following places.
Page 330 4-3. Do-it-yourself maintenance Passenger’s side instrument panel 1. Open the glove box. Slide off the damper. 2. Push in each side of the glove box to disconnect the claws. STEP After a system failure, see “Fuse layout and amperage rat- ings”...
Page 331 4-3. Do-it-yourself maintenance Take out the pullout tool. STEP Only type A fuse can be removed using the pullout tool. STEP Check if the fuse has blown. Type A Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid.
Page 332 4-3. Do-it-yourself maintenance Type C Normal fuse Blown fuse Contact your Toyota dealer. Type D Normal fuse Blown fuse Contact your Toyota dealer. I n f o r ma t i o n P r o v i d e d b y :...
Page 333 4-3. Do-it-yourself maintenance Fuse layout and amperage ratings Engine compartment Fuse Ampere Circuit Headlights, daytime running light MAIN 30 A system, H-LP RL, H-LP LL 30 A INJ, IGN, GAUGE 2 Multiport fuel injection system/ ETCS 10 A sequential multiport fuel injection system Daytime running light system, 20 A...
Page 334 4-3. Do-it-yourself maintenance Fuse Ampere Circuit RAD NO.1 15 A Audio system Multiport fuel injection system/ EFI NO.1 20 A sequential multiport fuel injection system, EFI NO.2 ALT-S 7.5 A Charging system Turn signal lights, emergency 15 A flashers Power sliding door, air conditioning system, power windows, multiplex ECU-B 10 A...
Page 335 4-3. Do-it-yourself maintenance Fuse Ampere Circuit L-PSD 30 A Left side power sliding door RR A/C 40 A Rear air conditioning system 40 A Rear window defogger, MIR HTR SPARE 7.5 A Spare fuse Charging system, RR A/C, HTR, 140 A FAN, PBD, R-PSD, L-PSD, DEF Anti-lock brake system, traction ABS1...
Page 336 4-3. Do-it-yourself maintenance Under the driver’s side instrument panel Fuse Ampere Circuit MIR HTR 10 A Outside rear view mirror defoggers Audio system, navigation system, RAD2 7.5 A rear seat entertainment system PWR OUTLET 15 A Power outlets 15 A Cigarette lighter Shift lock control system, air condi- ECU ACC...
Page 337 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Windshield washer and rear win- 20 A dow washer 10 A Air conditioning system Intuitive parking assist system, rear view monitor system, multiplex communication system, multiport fuel injection system/sequential multiport fuel injection system, anti- lock brake system, traction control system, vehicle stability control ECU-IG...
Page 338 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Stop/tail lights, high mounted stop- light, shift lock control system, anti- lock brake system, traction control system, vehicle stability control STOP 10 A system, multiport fuel injection sys- tem/sequential multiport fuel injec- tion system, multiplex communication system Power windows, power rear view 25 A...
Page 339 (→P. 486) If the replaced fuse blows again, have the vehicle inspected by your Toyota dealer. If there is an overload in the circuits The fuses are designed to blow before the entire wiring harness is damaged.
Page 340 Never use a fuse of a higher amperage rating than indicated, or use any other object in place of a fuse. Always use a genuine Toyota fuse or equivalent. Never replace a fuse with a wire, even as a temporary fix.
Page 341 You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer.
Page 342 4-3. Do-it-yourself maintenance Rear bulb locations Rear turn signal lights Back-up lights Stop/tail and rear side License plate lights marker lights Tail lights Replacing light bulbs Headlight (halogen bulbs) Turn the bulb base counterclock- STEP wise. Headlight (high beam) Headlight (low beam) Pull out the light bulb while STEP depressing the lock release.
Page 343 4-3. Do-it-yourself maintenance Front side marker light Turn the bulb base counterclock- STEP wise. Remove the light bulb. STEP I n f o r ma t i o n P r o v i d e d b y :...
Page 344 4-3. Do-it-yourself maintenance Parking and front turn signal lights Turn the bulb base counterclock- STEP wise. Remove the light bulb. STEP I n f o r ma t i o n P r o v i d e d b y :...
Page 345 4-3. Do-it-yourself maintenance Rear turn signal, stop/tail and rear side marker lights Remove the securing bolts and STEP remove the unit. To protect the cover, place a rag between the flathead screwdriver and cover as shown in the illus- tration. Turn the bulb bases counter- STEP clockwise.
Page 346 4-3. Do-it-yourself maintenance Tail and back-up lights Open the back door and remove STEP the strap. Remove the back door trim STEP board. Turn the bulb bases counter- STEP clockwise. Remove the light bulbs. STEP Tail light Back-up light I n f o r ma t i o n P r o v i d e d b y :...
Page 347 4-3. Do-it-yourself maintenance License plate lights Open the back door and remove STEP the strap. Remove the back door trim STEP board. Turn the bulb bases counter- STEP clockwise. Remove the light bulb. STEP I n f o r ma t i o n P r o v i d e d b y :...
Page 348 The high mounted stoplight consists of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced. I n f o r ma t i o n P r o v i d e d b y :...
Page 349 Doing so could result in electric shock and serious injury or death. Discharge headlights Contact your Toyota dealer before replacing discharge headlights (includ- ing light bulbs). Do not touch the high-intensity discharge headlight’s high voltage socket when the headlights are turned on.
Page 350 If your vehicle needs to be towed If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or a commercial towing service, using a lift-type truck or a flat bed truck. Use a safety chain system for all towing, and abide by all state/pro- vincial and local laws.
Page 351 5-1. Essential information Towing with a sling-type truck NOTICE To prevent body damage Do not tow with a sling-type truck, either from the front or rear. Towing with a wheel-lift type truck from the front 2WD models Release the parking brake. I n f o r ma t i o n P r o v i d e d b y :...
Page 352 5-1. Essential information AWD models Use a towing dolly under the rear wheels. NOTICE To prevent damaging the vehicle When raising the vehicle, ensure adequate ground clearance for towing at the opposite end of the raised vehicle. Without adequate clearance, the vehicle could be damaged while being towed.
Page 353 5-1. Essential information Using a flat bed truck If you use chains or cables to tie down your vehicle, the angles shaded in black must be 45°. Do not overly tighten the tie downs or the vehicle may be damaged. I n f o r ma t i o n P r o v i d e d b y :...
Page 354 5-1. Essential information If you think something is wrong If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact your Toyota dealer as soon as possible. Visible symptoms l Fluid leaks under the vehicle (Water dripping from the air conditioning after use is normal.)
Page 355 5-1. Essential information Fuel pump shut off system To minimize the risk of fuel leakage when the engine stalls or an air- bag inflates upon collision, the fuel pump shut off system stops sup- plying fuel to the engine. Follow the procedure below to restart the engine after the system is activated.
Page 356 5-1. Essential information Event data recorder Your vehicle has computers that monitor and control certain aspects of your vehicle. These computers assist in driving and maintaining optimal vehicle performance. Besides storing data useful for troubleshooting, there is an event data recorder (EDR) that records data in a crash or a near car crash event.
Page 357 5-1. Essential information Disclosure of the data Toyota will not disclose the data recorded in an EDR to a third party except when: l An agreement from the vehicle's owner (or the leasing company for a leased vehicle) is obtained...
Page 358 Stop the vehicle immediately. Continuing to drive the vehicle may be dangerous. The following warning indicates a possible problem in the brake sys- tem. Immediately stop the vehicle in a safe place and contact your Toyota dealer. Warning light Warning light/Details Brake system warning light (warning buzzer)* •...
Page 359 Have the vehicle inspected immediately. Failing to investigate the cause of the following warnings may lead to the system operating abnormally and possibly cause an accident. Have the vehicle inspected by your Toyota dealer immediately. Warning light Warning light/Details Malfunction indicator lamp Indicates a malfunction in: (U.S.A.)
Page 360 If the malfunction indicator lamp does not go off even after several trips, con- tact your Toyota dealer as soon as possible. I n f o r ma t i o n P r o v i d e d b y :...
Page 361 5-2. Steps to take in an emergency Follow the correction procedures. After taking the specified steps to correct the suspected problem, check that the warning light turns off. Warning light Warning light/Details Correction procedure Open door warning light Check that all doors are Indicates that a door is not closed.
Page 362 When the light comes on after blinking for 1 minute: Have the system checked Malfunction in the tire by your Toyota dealer. pressure warning system Third seat warning light Indicates that the third Complete the third seat seat operation is not yet operation.
Page 363 5-2. Steps to take in an emergency Warning light Warning light/Details Correction procedure Dynamic laser cruise con- trol master warning light Indicates a malfunction in the dynamic laser cruise →P. 204 control system. When the light comes on, the alarm sounds and the warning code will appear on the display.
Page 364 5-2. Steps to take in an emergency Front passenger detection sensor and passenger seat belt reminder If luggage is placed on the front passenger seat, the front passenger detection sensor may cause the warning light to flash, even if a passen- ger is not sitting in the seat.
Page 365 If there is a lot of snow or ice on the vehicle, in particular around the wheels or wheel housings. If non-genuine Toyota wheels are used. (Even if you use Toyota wheels, the tire pressure warning system may not work properly with some types of tires.)
Page 366 • If the tire pressure warning light comes on even after tire inflation pressure adjustment, it is probable that you have a flat tire. Have the tire replaced by the nearest Toyota dealer. • Avoid abrupt maneuvering and braking. If the vehicle tires deterio- rate, you could lose control of the steering wheel or the brakes.
Page 367 5-2. Steps to take in an emergency CAUTION Maintenance of the tires Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label (tire and load information label).
Page 368 5-2. Steps to take in an emergency CAUTION Your vehicle has also been equipped with a TPMS (tire pressure warning system) malfunction indicator to indicate when the system is not operat- ing properly. The TPMS (tire pressure warning system) malfunction indi- cator is combined with the low tire pressure telltale (tire pressure warning light).
Page 369: If You Have A Flat Tire
5-2. Steps to take in an emergency If you have a flat tire (vehicles with run-flat tires) Take your vehicle to the nearest Toyota dealer or authorized tire dealer as soon as possible. Run-flat tires (A “RFT” or “DSST” mark is molded on the...
Page 370 5-2. Steps to take in an emergency If you have a flat tire (vehicles with standard tires) Remove the flat tire and replace it with the spare provided. Before jacking up the vehicle l Stop the vehicle on a hard, flat surface. l Set the parking brake.
Page 371 5-2. Steps to take in an emergency Type B Tire bag Jack handle Wheel nut wrench Jack Spare tire Taking out the jack and tools Turn the knobs to the “OPEN” STEP position and remove the cover. Remove the adapter socket. STEP (Type A only) The adapter socket is in a bag.
Page 372 5-2. Steps to take in an emergency Remove the jack. STEP Remove the wheel nut wrench. STEP Taking out the spare tire (type A) STEP Slide the front passenger’s seat to the front-most lock position and the right side second seat to the rear-most lock position so they will not interfere with the jack handle.
Page 373 5-2. Steps to take in an emergency Attach the adapter socket over STEP the spare tire clamp bolt. Connect the jack handle and the adapter socket. Turn the jack handle. The tire will be lowered com- pletely to the ground. Take the spare tire out from STEP underneath...
Page 374 5-2. Steps to take in an emergency Replacing a flat tire Chock the tires. STEP Wheel Flat tire chock posi- tions Behind the Left- rear right- hand hand side side tire Front Behind the Right- rear left- hand hand side side tire In front of...
Page 375 5-2. Steps to take in an emergency Slightly loosen the wheel nuts STEP (one turn). Turn the tire jack portion “A” by STEP hand until the notch of the jack is in contact with the jack point. Raise the vehicle until the tire is STEP slightly raised off the ground.
Page 376 5-2. Steps to take in an emergency Installing the spare tire Remove any dirt or foreign mat- STEP ter from the wheel contact sur- face. If foreign matter is on the wheel contact surface, the wheel nuts may loosen while the vehicle is in motion, and the tire may come off the vehicle.
Page 377 5-2. Steps to take in an emergency Lower the vehicle. STEP Firmly tighten each nut two or STEP three times in the order shown in the illustration. Tightening torque: 76 ft•lbf (103 N•m, 10.5 kgf•m) STEP Stow the flat tire, tire jack and all tools. Stowing the flat tire Wrap the flat tire in the tire bag and stow temporarily in the lug-...
Page 378 5-2. Steps to take in an emergency When reinstalling the wheel ornament (vehicles with a steel wheel) Align the cutout of the wheel ornament with the valve stem as shown. When stowing the adapter socket (Type A only) Insert the bag with the fold portion facing downward. The compact spare tire The compact spare tire is identified by the label “TEMPORARY USE ONLY”...
Page 379 5-2. Steps to take in an emergency CAUTION Using the tire jack Improper use of the tire jack may lead to death or injuries due to the vehicle suddenly falling off the jack. Do not use the tire jack for any purpose other than replacing tires or installing and removing tire chains.
Page 380 5-2. Steps to take in an emergency CAUTION Replacing a flat tire Observe the following precautions to reduce the risk of death or serious injury: Remove the spare tire before jacking up the vehicle. If the spare tire is removed after jacking up the vehicle, the tire carrier and the spare tire may interfere with the jack and cause a serious accident.
Page 381 5-2. Steps to take in an emergency CAUTION When the spare tire is installed The vehicle speed may not be correctly detected, and the following sys- tems may not operate correctly: ABS & Brake assist TRAC Navigation system (if equipped) I n f o r ma t i o n P r o v i d e d b y :...
Page 382 When replacing the tires When removing or fitting the wheels, tires or the tire pressure warning valve and transmitter, contact your Toyota dealer as the tire pressure warning valve and transmitter may be damaged if not handled correctly. To avoid damaging the tire pressure warning valves and transmit- ters Do not use liquid sealants on flat tires.
Page 383 One or both of the battery terminals may be disconnected. l The battery may be discharged. (→P. 532) Contact your Toyota dealer if the problem cannot be repaired, or if repair procedures are unknown. I n f o r ma t i o n P r o v i d e d b y :...
Page 384 (a system to prevent accidental operation of the shift lever). Have the vehicle inspected by your Toyota dealer. The following steps may be used as an emergency measure to ensure that the shift lever can be shifted.
Page 385 5-2. Steps to take in an emergency If you lose your keys/wireless remote control transmitter Keys New genuine keys can be made by your Toyota dealer. Bring a master key and the key number stamped on the key number plate.
Page 386 You can call your Toyota dealer or qualified repair shop. If you have a set of jumper (or booster) cables and a second vehi- cle with a 12-volt battery, you can jump start your Toyota following the steps below. STEP...
Page 387 Once the vehicle’s engine has started, remove the jumper cables in the exact reverse order in which they were con- nected. Once the engine starts, have the vehicle checked at your Toyota dealer as soon as possible. Starting the engine when the battery is discharged The engine cannot be started by push-starting.
Page 388 5-2. Steps to take in an emergency CAUTION Avoiding battery fires or explosions Observe the following precautions to prevent accidentally igniting the flam- mable gas that may be emitted from the battery. Make sure the jumper cable is connected to the correct terminal and that it is not unintentionally in contact with any part other than the intended termi- nal.
Page 389 5-2. Steps to take in an emergency NOTICE When handling jumper cables Be careful that the jumper cables do not become tangled in the cooling fans or any of the belts when connecting or disconnecting them. I n f o r ma t i o n P r o v i d e d b y :...
Page 390 Wait until the temperature of the engine (shown on the instrument cluster) begins to fall and then stop the engine. If the fans are not operating: Stop the engine and call your Toyota dealer. After the engine has cooled STEP STEP...
Page 391 (→ unavailable. P. 546 Have the vehicle checked at the nearest Toyota dealer as soon as possible. Overheating If you observe the following, your vehicle may be overheating. The engine coolant temperature gauge enters the red zone or a loss of power is experienced.
Page 392 5-2. Steps to take in an emergency NOTICE When adding engine coolant Wait until the engine has cooled down before adding engine coolant. When adding coolant, do so slowly. Adding cool coolant to a hot engine too quickly can cause damage to the engine. I n f o r ma t i o n P r o v i d e d b y :...
Page 393 5-2. Steps to take in an emergency If the vehicle becomes stuck Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt, or snow. STEP Stop the engine. Set the parking brake and put the shift lever in P.
Page 394 5-2. Steps to take in an emergency I n f o r ma t i o n P r o v i d e d b y :...
Page 395 6-1. Specifications Maintenance data (fuel, oil level, etc.) Dimensions and weights Overall length 201.0 in. (5105 mm) Overall width 77.4 in (1965 mm) Overall height 68.9 in (1750 mm) Wheelbase 119.3 in (3030 mm) 65.6 in (1665 mm) Front 65.9 in (1675 mm) Tread 66.9 in (1700 mm) Rear...
Page 396: 6-1. Specifications
Vehicle identification number The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle. This number is stamped on the top left of the instrument panel.
Page 397 6-1. Specifications Engine Model 2GR-FE engine Type 6 cylinder V type, 4 cycle, gasoline 3.70 × 3.27 in. (94.0 × 83.0 mm) Bore and stroke Displacement 210.9 cu.in. (3456 cm Drive belt tension Automatic adjustment Valve clearance Fuel Fuel type Unleaded gasoline only Octane rating 87 (Research Octane Number 91) or higher...
Page 398 6.4 qt. (6.1 L, 5.4 Imp.qt.) Without filter 6.0 qt. (5.7 L, 5.0 Imp.qt.) Oil grade ILSAC multigrade engine oil Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the grade and viscosity shown below. Recommended oil viscosity...
Page 399: Spark Plug
Cooling system Capacity 12.0 qt. (11.3 L, 10.0 Imp.qt.) (Reference) Use either of the following. • “Toyota Super Long Life Coolant” • Similar high-quality ethylene glycol-based non- Coolant type silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technol- Do not use plain water alone.
Page 400 Toyota Genuine ATF WS NOTICE Automatic transmission fluid type Using automatic transmission fluid other than “Toyota Genuine ATF WS” may cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damage the transmission of your vehicle.
Page 401 6-1. Specifications Brakes Pedal clearance 2.0 in. (52 mm) 0.04 ⎯ 0.24 in. (1 ⎯ 6 mm) Pedal free play Brake pad wear limit 0.04 in. (1.0 mm) Parking brake lining wear limit 0.04 in. (1.0 mm) 3 ⎯ 5 clicks Parking brake pedal travel Fluid type SAE J1703 or FMVSS No.116 DOT 3...
Page 402: Tail Lights
6-1. Specifications Light bulbs Light Bulbs Bulb No. Type Headlights (low beam) ⎯ With discharge headlights Without discharge headlights 9006 Headlights (high beam) 9005 Front fog lights 9006 Front turn signal and parking 3457A 27/7 lights ⎯ Front side marker lights Exterior Rear turn signal lights 7440...
Page 403 ASTM D4814 in the U.S.A. and CGSB3.5-M93 in Canada. Fuel tank opening for unleaded gasoline To help prevent incorrect fueling, your Toyota has a fuel tank opening that only accommodates the special nozzle on unleaded fuel pumps. If your engine knocks Consult your Toyota dealer.
Page 404 Toyota allows the use of oxygenate blended gasoline where the oxygen- ate content is up to 10% ethanol or 15% MTBE. If you use gasohol in your Toyota, be sure that it has an octane rating no lower than 87.
Page 405 6-1. Specifications NOTICE Notice on gasoline quality Do not use leaded gasoline. Leaded gasoline can cause damage to your vehicle’s catalytic converters causing the emission control system to malfunction. Do not use gasohol other than that stated here. Other gasohol may cause fuel system damage or vehicle performance problems.
Page 406: Tire Information
6-1. Specifications Tire information Typical tire symbols Run-flat tire or standard tire Compact spare tire Tire size (→P. 556) DOT and Tire Identification Number (TIN) (→P. 555) Uniform tire quality grading For details, see “Uniform Tire Quality Grading” that follows. Location of treadwear indicators (→P.
Page 407 6-1. Specifications Run-flat tire (RFT) or standard tire (→P. 515) This vehicle can be equipped with either run-flat tires (RFT) or standard tires. A “RFT” or “DSST” mark is molded on the sidewall of the run-flat tire. Tire ply composition and materials Plies are layers of rubber-coated parallel cords.
Page 408: Tire Identification Number
6-1. Specifications Typical DOT and Tire Identification Number (TIN) DOT symbol Tire Identification Number (TIN) Tire manufacturer's identifica- tion mark Tire size code Manufacturer's optional tire type code (3 or 4 letters) Manufacturing week Manufacturing year : The DOT symbol certifies that the tire conforms to applicable Federal...
Page 409 6-1. Specifications Tire size Typical tire size information The illustration indicates typical tire size. Tire use (P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 or 3 digits) Speed symbol...
Page 410: Uniform Tire Quality Grading
U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading. Your Toyota dealer will help answer any questions you may have as you read this information. DOT quality grades All passenger vehicle tires must conform to Federal Safety Requirements in addition to these grades.
Page 411 6-1. Specifications Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speci- fied government test course. For example, a tire graded 150 would wear one and a half (1-1/2) times as well on the government course as a tire graded 100.
Page 412 6-1. Specifications Warning: The temperature grades for this tire are established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either sepa- rately or in combination, can cause heat buildup and possible tire fail- ure.
Page 413 6-1. Specifications Tire related term Meaning 150 lb. (68 kg) times the number of occupants Normal occupant specified in the second column of Table 1 that weight follows Distribution of occupants in a vehicle as speci- Occupant distribution fied in the third column of Table 1 below The combined weight of installed regular pro- duction options weighing over 5 lb.
Page 414 6-1. Specifications Tire related term Meaning The surface area of the rim not covered by the Weather side inflated tire The part of the tire that is made of steel wires, Bead wrapped or reinforced by ply cords and that is shaped to fit the rim A breakdown of the bond between components Bead separation...
Page 415 6-1. Specifications Tire related term Meaning The parting of the innerliner from cord material Innerliner separation in the carcass (a) The sidewall that contains a whitewall, bears white lettering, or bears manufac- turer, brand, and/or model name molding that is higher or deeper than the same Intended outboard molding on the other sidewall of the tire, or sidewall...
Page 416 6-1. Specifications Tire related term Meaning A layer of rubber-coated parallel cords A parting of rubber compound between adja- Ply separation cent plies A mechanical device made of rubber, chemi- cals, fabric and steel or other materials, that, Pneumatic tire when mounted on an automotive wheel, pro- vides the traction and contains the gas or fluid that sustains the load...
Page 417 6-1. Specifications Tire related term Meaning That portion of a tire that comes into contact Tread with the road A tread section running circumferentially Tread rib around a tire Tread separation Pulling away of the tread from the tire carcass The projections within the principal grooves Treadwear indicators designed to give a visual indication of the...
Page 418 Your vehicle includes a variety of electronic features that can be per- sonalized to your preferences. Programming these preferences requires specialized equipment and may be performed by your Toy- ota dealer. Some function settings are changed simultaneously with other functions being customized. Contact your Toyota dealer. Customized Item Function Default setting...
Page 419 6-2. Customization Customized Item Function Default setting setting Power sliding door Press twice operation Wireless Press and hold One short press remote con- trol → P. 27) Power back door oper- Press twice ation Press and hold One short press Driver's door unlocked in one All doors...
Page 420: Engine Switch
6-2. Customization Customized Item Function Default setting setting 7.5 seconds Time elapsed before 15 seconds lights turn off 30 seconds Operation when the Illumination doors are unlocked → P. 361) Operation after the engine switch is turned to the “LOCK” position Outer foot lights Seat belt Vehicle speed linked...
Page 421 6-3. Initialization Items to initialize The following items must be initialized for normal system operation in cases such as after maintenance is performed on the vehicle. Item When to initialize Reference Power sliding door After reconnecting or changing the P. 37 (if equipped) battery Power back door...
Page 422 If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800-331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 423 Seat belt instructions for Canadian owners (in French) The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions in English. Utilisation correcte des ceintures de sécurité...
Page 424 ATTENTION ■ Lorsque vous utilisez la ceinture de sécurité du siège central de la troisième rangée N'utilisez pas la ceinture de sécurité du siège central de la troisième rangée avec l'une l'autre boucles déverrouillées. Si une seule des boucles est verrouillée, ceci peut entraîner des blessures graves, voire mortelles en cas de freinage brusque ou de collision.
Page 425 Entretien et soin ■ Ceintures de sécurité Nettoyez avec un chiffon ou une éponge humectée d'eau savonneuse tiède. Profitez de l'occasion pour vérifier régulièrement que les ceintures ne sont pas effilochées, entaillées, ou ne paraissent pas exagérément usées. ATTENTION ■ Détérioration et usure des ceintures de sécurité...
Page 426 I n f o r ma t i o n P r o v i d e d b y :...
Page 427 Alphabetical index Alphabetical index A/C.....246, 240, 256, 253 Side airbag operating ABS ...........215 conditions ......120 Air conditioning filter....469 Side airbag precautions ..124 Air conditioning system SRS airbags......117 Air conditioning filter....469 Alarm......... 112 Front automatic air Antenna ........268 conditioning system ....246 Anti-lock brake system ...
Page 428 Alphabetical index Back-up lights Child restraint system Replacing light bulbs .... 486 Booster seats, definition..135 Wattage ........ 549 Booster seats, installation ..139 Back door Convertible seats, Back door ....... 47 definition ......135 Wireless remote control..27 Convertible seats, Battery installation......139 Checking ......
Page 429 Alphabetical index Cleaning Daytime running light Exterior........418 system ........188 Interior ........421 Defogger Seat belts ......422 Rear window ......260 Clock .........385 Side mirrors......260 Coat hooks .......396 Dimension ........ 542 Coin holder .......369 Dinghy towing ......237 Compass........413 Display Condenser ........446 Dynamic laser cruise Console box ......365 control.........
Page 430 Alphabetical index Emergency, in case of Engine coolant If the back door opener is Capacity ........546 inoperative ......49 Checking .......444 If the engine will not start..529 Preparing and checking before If the shift lever cannot be winter ........226 shifted ........
Page 431 Alphabetical index Front fog lights Garage door opener ....405 Replacing light bulbs .....486 Garage door opener box ..410 Switch........190 Gas station information ..592 Wattage.........549 Gauges........174 Front manual air conditioning Glove box ......... 365 system ........240 Grocery bag hooks ....394 Front passenger occupant classification system ....129 Hands-free system...
Page 432 Alphabetical index I/M test........429 License plate lights Identification Replacing light bulbs .....486 Engine ........543 Wattage.........549 Vehicle........543 Light bulbs Ignition switch ......167 Replacing ......486 Illuminated entry system ..361 Wattage.........549 Indicator lights ......177 Lights Initialization Door courtesy lights ....361 Items to initialize....
Page 433 Alphabetical index Maintenance Parking assist sensors.... 209 Do-it-yourself Parking brake ......173 maintenance .......430 Parking lights General maintenance....426 Replacing light bulbs..... 486 Maintenance data....542 Switch ........185 Maintenance requirements..424 Wattage......... 549 Meter Personal lights Instrument panel light Switch ........362 control .........176 Wattage.........
Page 434 Alphabetical index Rear turn signal lights Seats Replacing light bulbs .... 486 Adjustment ....56, 59, 61 Wattage ........ 549 Adjustment Rear window defogger.... 260 precaution ....58, 60, 62 Rear window wiper....193 Child seats/child restraint Replacing system installation ....139 Fuses........474 Cleaning ........421 Light bulbs ......
Page 435 Alphabetical index Spare tire Tables Inflation pressure....548 Front seat side table ..... 399 Spare tire.......516 Seatback tables ....397 Spark plug ........546 Tachometer ......174 Specifications......542 Tail lights Speech command switch ..332 Replacing light bulbs..... 486 Speedometer ......174 Switch ........185 Steering Wattage.........
Page 436 Alphabetical index Towing Warning buzzers Dinghy towing....... 237 Brake system ......504 Trailer towing......229 Seat belt reminder....507 Traction control....... 215 Warning lights TRAC ........215 Anti-lock brake system ..505 Trays......... 380 Brake assist system ....505 Trip information display ..181 Brake system ......504 Trip meter.........
Page 437 Alphabetical index Weight Cargo capacity ......219 Load limits ......225 Weight ........542 Wheels ........467 Window glasses ......99 Window lock switch....99 Windows Power windows ....99, 101 Rear window defogger ..260 Washer......191, 193 Windshield wiper de-icer..260 Windshield wipers ....191 Wireless remote control Replacing the battery ....472 Wireless remote control ..27 WMA disc........279 I n f o r ma t i o n P r o v i d e d b y :...
Page 438 Drain and refill Without filter 6.0 (5.7, 5.0) (Reference) With filter 6.4 (6.1, 5.4) Toyota Genuine Motor Oil or equivalent Oil grade: P. 545 Engine oil type ILSAC multigrade engine oil Recommended oil viscosity: SAE 5W-30 I n f o r ma t i o n P r o v i d e d b y :...

Toyota SIENNA 2009 Quick Reference Manual

Overview

Keyless Entry

Features/Operations

Auto Lock Functions 2

Lights 1 & Turn Signals

Seat Belts-Shoulder Belt Anchor

Quick Links

Related Manuals for Toyota SIENNA 2009

Summary of Contents for Toyota SIENNA 2009

Table of Contents