Page 1: Occupant Restraint Systems
None of these systems, either individ- Toyota encourages you and your family to take the time to ually or together, can ensure that there is no injury in the read Section 1−3 of this Owner’s Manual carefully.
Page 2: Event Data Recorder
Toyota recommends you to read the provisions in Section D Engine speed 1−3 carefully and refer to them as needed during your time D Whether the brake pedal was applied or not of ownership of this vehicle.
Page 3 D Disclose summarized data cleared of vehicle identifi- Toyota will not disclose the data recorded in an EDR to a cation information to a non−Toyota organization for third party except when: research purposes D An agreement from the vehicle’s owner (or the leas-...
Page 4 07 12.25 New vehicle warranty Important health and safety information about your Toyota Your new vehicle is covered by the following Toyota limited warranties: CAUTION D New vehicle warranty D Emission control systems warranty WARNING: Engine exhaust, some of its constitu-...
Page 5 Toyota Toyota A wide variety of non−genuine spare parts and accessories The spark ignition system in your Toyota meets all require- for Toyota vehicles are currently available in the market. ments of the Canadian Interference−Causing Equipment You should know that Toyota does not warrant these prod- Standard.
Page 6 As the installation of a mobile two−way radio system in your vehicle could affect electronic systems such as fol- lows, be sure to check with your Toyota dealer for precau- tionary measures or special instructions regarding installa- Tires and loading on your tion.
Page 7: Driving Tips
In addition, this vehicle shop or by your Toyota dealer before you dispose of your has a higher ground clearance and center of gravity than vehicle.
Page 8 07 12.25 Leak detection pump This pump performs fuel evaporation leakage check. This check is done approximately five hours after the engine is turned off. So you may hear sound coming from under- neath the luggage compartment for several minutes. It does not indicate a malfunction.
Page 9 07 12.25 SECTION INDEX...
Page 10: Table Of Contents
..Charging system warning light ..Protecting your Toyota from Back window wiper and Checking and replacing fuses ..
Page 11 07 12.25 Cleaning the interior ....Clock ....... Defogger Economical driving Coin holder...
Page 12 07 12.25 Engine If you have a flat tire ....Gauge ......Before starting the engine .
Page 13 07 12.25 I/M test ......Light bulbs Maintenance Identification Back−up light ..... . Do−it−yourself maintenance .
Page 14 07 12.25 Protecting your Toyota from Running board light ....corrosion ......
Page 15 07 12.25 SRS side airbags and Three−way catalytic converters ..Types of tires ......curtain shield airbags .
Page 16: Operation Of Instruments And
07 12.25 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Overview of instruments and controls Instrument panel overview ........Instrument cluster overview .
Page 17: Instrument Panel Overview
13. Seat heater switches 14. Rear height control air suspension switch 15. Rear vents 16. Trash holder 17. Toyota electronic modulated suspension mode select switch 18. Downhill assist control switch 19. Front cup holders 20. Tilt steering lock release lever...
Page 18 07 12.25 21. Telescopic steering lock release lever 22. Parking brake pedal 23. Window lock switch 24. Power rear view mirror control switches CY11048 Rear console box 1. Power outlet (12 VDC) 2. Power outlet (115 VAC) 3. AUX adapter 4.
Page 19 07 12.25 1. Driving position memory switches 2. Headlight, turn signal and front fog light switches 3. Wiper and washer switches 4. Power back window switch 5. Audio system/rear view monitor system and navigation system including audio system (For the navigation system, see the separate “Navigation System Owner’s Manual”.) 6.
Page 20 07 12.25 "Steering switches 15. Engine switch 16. Cruise control switch 17. Hood lock release lever 18. Fuel filler door opener 19. Roll sensing of curtain shield airbags CY11065 off switch 20. “VSC OFF” switch 21. Center differential lock switch 22.
Page 21: Instrument Cluster Overview
07 12.25 Instrument cluster overview "Type A CY11062 1. Tachometer 4. Fuel gauge 7. Trip meter reset knob 2. Speedometer 5. Low fuel level warning light 8. Odometer and two trip meters 3. Service reminder indicators and 6. Engine coolant temperature gauge indicator lights...
Page 22 07 12.25 "Type B CY11067 1. Service reminder indicators and 3. Speedometer 6. Engine coolant temperature gauge indicator lights 4. Fuel gauge 7. Trip meter reset knob 2. Tachometer 5. Low fuel level warning light 8. Odometer and two trip meters...
Page 23: Indicator Symbols
07 12.25 Indicator symbols on the instrument panel ∗ 1 ∗ 1 Brake system warning light Open door warning light ∗ 1 ∗ 1 Driver’s seat belt reminder light SRS warning light Automatic transmission fluid temperature ∗ 1 Front passenger’s seat belt reminder light ∗...
Page 24 07 12.25 ∗ 3 Four−wheel drive indicator light Headlight low beam indicator light (multi−mode four−wheel drive models) Tail light indicator light Slip indicator light Headlight high beam indicator light “AUTO LSD” indicator light Downhill assist control system indicator light Turn signal indicator lights (four−wheel drive models) Front fog light indicator light Height control indicator lights...
Page 25 07 12.25 ∗ 1 : For details, see “Service reminder indicators and warning buzzers” on page 149 in Section 1−6. ∗ 2 : For details, see “Roll sensing of curtain shield airbags off switch” on page 95 in Section 1−3. ∗...
Page 26 07 12.25 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Keys and Doors Keys ............Engine immobilizer system .
Page 27: Keys
When using a key containing a trans- 1. Master keys (black)—These keys work ponder chip, observe the following in every lock. Your Toyota dealer will precautions: need one of them to make a new key with a built−in transponder chip.
Page 28 07 12.25 z Do not cover the key grip with any material that cuts off electromagnet- ic waves. z Do not knock the key hard against other objects. CY12023 CY12024 z Do not leave the key exposed to high temperatures for a long period, such as on the dashboard and hood under direct sunlight.
Page 29: Engine Immobilizer System
Toyota dealer. need additional keys, duplicates can be the electronic code in the chip corre- made by a Toyota dealer using the key The indicator light stays on except sponds to the registered ID code for number.
Page 30: Wireless Remote Control
The system is maintenance−free. (1) this device may not cause harmful CY12070 For your Toyota dealer to make you a interference, and (2) this device must new key with built−in transponder chip, accept any interference received, includ-...
Page 31 20. damage to the transmitter. If you lose your transmitter, contact your Do not leave the transmitter in places Toyota dealer as soon as possible to Locking operation where the temperature becomes high avoid possibility theft, such as on the dashboard.
Page 32 For Toyota dealer. details, contact your Toyota dealer. To lock: Push the “LOCK” switch. All the Cancelling the wireless door locking or side doors and back door are locked si- When the “UNLOCK”...
Page 33 The back window opening program by You can also stop the alarm by turning wireless remote control can be changed or the engine switch from the “LOCK” to disabled. For details, contact your Toyota “ON” position. dealer.
Page 34 07 12.25 For vehicles sold in U.S.A. NOTICE: Reorient or relocate the receiving an- This equipment has been tested and tenna. This device complies with Part 15 of the found to comply with the limits for a FCC Rules. Operation is subject to the Increase the separation between the Class B digital device, pursuant to Part following two conditions:...
Page 35: Replacing Battery
1. Using a coin or equivalent, open the ponents. transmitter case. z Replace only with same equivalent type recommended by a Toyota dealer. z Dispose of used batteries according to the local laws. Replace the transmitter battery by follow- ing these procedures:...
Page 36 After replacing the battery, check that the transmitter operates properly. If the trans- mitter still does not operate properly, con- tact your Toyota dealer. 2. Remove the discharged transmitter bat- 3. Put in a new transmitter battery with tery by ballpoint pen.
Page 37: Side Doors
This double key turning operation to un- lock all the side doors and back door can be changed to a single key turning opera- tion. For details, contact your Toyota deal-...
Page 38 The doors front side. will open and an accident may occur. To unlock: Push the switch down on the Toyota strongly recommends that all rear side. children be placed in the rear seat of the vehicle.
Page 39 This unlocking protection with the power door lock switch can be disabled. For de- REAR DOOR CHILD−PROTECTORS tails, contact your Toyota dealer. Move the lock lever to the “LOCK” position as shown on the label. When the child−protector is locked, you cannot open the rear door by the inside door handle.
Page 40: Automatic Door Locking And Unlocking Functions
07 12.25 —Automatic door locking and unlocking functions AUTOMATIC DOOR LOCKING To select the locking linked with the To select the locking linked with the shift position: vehicle speed: You can select the following functions: 1. Close all doors and turn the engine 1.
Page 41 07 12.25 AUTOMATIC DOOR UNLOCKING To select the unlocking linked with the To select the unlocking linked with the shift position: engine switch: You can select the following functions: 1. Close all doors and turn the engine 1. Close all doors and turn the engine Unlocking linked with the shift posi- switch to the “ON”...
Page 42: Power Windows
07 12.25 Power windows OPERATING THE DRIVER’S WINDOW Use the switch on the driver’s door. Normal operation: The window moves as long as you hold the switch. To open: Lightly push down the switch. CY12005 CY12006 To close: Lightly pull up the switch. The windows can be operated with the Automatic operation: Push the switch switch on each side door.
Page 43 If the power window cannot operated properly, have checked by your Toyota dealer. CAUTION Never try jamming any part of your body to activate the jam protection function intentionally, as it could re- sult in death or serious injury.
Page 44 07 12.25 OPERATING PASSENGERS’ CAUTION Never leave anyone (particularly a WINDOWS small child) alone in your vehicle, Use the switch on each passenger’s To avoid death or serious injury, you especially with the key still door or the switches on the driver’s must do the following.
Page 45: Power Back Window
Toyota dealer. The power back window works when the engine switch is in the “ON” position. OPERATING FROM INSIDE CAUTION You can open the back window when the The engine switch must be in the “ON”...
Page 46 This door key linked function can be dis- be operated. abled. For details, contact your Toyota dealer. Jam protection function: During closing operation, the window stops and opens half way if something gets caught between the window and window frame.
Page 47: Back Door
The jam protection function may except when the battery is disconnected back window switch without super- not work if something gets caught or run down, contact your Toyota dealer. vision. Use the window lock switch just before the window...
Page 48: Back Door Lock
(For details, see “Interi- the back door cannot be opened properly, or light” on page 136, “Luggage compart- have it checked by your Toyota dealer. ment light” on page 138, “Engine (ignition) The back door can be locked or unlocked switch light”...
Page 49: Hood
07 12.25 Hood CAUTION Keep the back window and back door closed while driving. This not only keeps the luggage from being CY12053 CY12087 thrown out but also prevents ex- haust gases from entering the ve- hicle. Careful attention is needed so as not to get your fingers trapped as the back door automatically closes when it has not been fully closed.
Page 50: Theft Deterrent System
07 12.25 Theft deterrent system The system will automatically be set after 30 seconds. When the system is set, the indicator light will start flashing again. 4. After making sure the indicator light starts flashing, you may leave the ve- hicle.
Page 51 If the system does not work properly, tomatically. trol transmitter, and the alarm will stop. have it checked by your Toyota dealer. After one minute, the alarm will automati- cally stop and the indicator light will starts flashing again.
Page 52: Fuel Tank Cap
07 12.25 Fuel tank cap CY12081 CY12055 CY12060 This indicates that the fuel filler door 1. To open the fuel filler door, pull the 2. To remove the fuel tank cap, turn is on the left side of your vehicle. lever.
Page 53 Make sure the cap is tightened securely. CY12056 The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible. CAUTION Make sure the cap is installed se- curely to prevent fuel spillage in the event of an accident.
Page 54: Electric Moon Roof
07 12.25 Electric moon roof To operate the moon roof, use the The roof will fully close automatically. To switch beside the personal lights. stop the roof partway, push the switch on either the “SLIDE OPEN” or “TILT UP” The moon roof works when the engine side quickly.
Page 55 It stops not be operated properly, have it checked especially with the key still working when either front door is opened. by your Toyota dealer. serted. Otherwise, he/she could use Jam protection function: moon roof switch...
Page 56 07 12.25 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Occupant restraint systems Seats ............Front seats .
Page 57: Seats
07 12.25 Front seats— Seats —Front seat precautions While the vehicle is being driven, all ve- Driver seat Slightly recline the back of hicle occupants should have the seatback seat. Although vehicle designs vary, upright, sit well back in the seat and prop- CAUTION many drivers can achieve the 250 erly wear the seat belts provided.
Page 58 07 12.25 —Seat adjustment precautions Front passenger seat Front seats CAUTION CAUTION CAUTION Do not adjust the seat while the vehicle is moving as the seat may The SRS front passenger airbag also The SRS side airbags are installed in unexpectedly move and cause the deploys with considerable force, and the driver and front passenger seats.
Page 59 07 12.25 —Adjusting front seats (manual seat) 1. SEAT POSITION ADJUSTING LEVER While adjusting the seat, do not put Hold the center of the lever and pull it your hands under the seat or near up. Then slide the seat to the desired the moving parts.
Page 60 07 12.25 —Adjusting front seats (power seat) 1. DRIVER’S SEAT: SEAT POSITION, CAUTION SEAT CUSHION ANGLE AND SEAT HEIGHT ADJUSTING SWITCH Avoid reclining seatback PASSENGER’S SEAT: SEAT POSITION more than needed. The seat belts pro- ADJUSTING SWITCH vide maximum protection in a frontal Move the control switch in the desired or rear collision when the driver and direction.
Page 61 07 12.25 —Flattening seatbacks (manual seat) CAUTION Avoid reclining seatback more than needed. The seat belts pro- vide maximum protection in a frontal CY13282 CY13283 or rear collision when the driver and the front passenger are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply re- straint forces directly to the abdomen...
Page 62 07 12.25 —Flattening seatbacks (power seat) CAUTION Do not allow passengers to ride on the flattened seat while driving; use the seat in the normal position. CY13135 CY13136 After putting back the seat, pushing the seat and seatback for- ward and rearward to make sure it is secured in place.
Page 63: Driving Position Memory System
07 12.25 Driving position memory system (on some models) This system can memorize the position CAUTION of the driver’s seat and recall it at the touch of a button. Do not allow passengers to ride on Buttons “1” and “2” can memorize two the flattened seat while driving;...
Page 64 07 12.25 To make only slight changes to an already To stop the operation, push any driving memorized position, the easiest way is to position memory button. first activate the memorized position, then To reactivate the system, push the button make the desired changes and perform “1”...
Page 65: Rear Seats
07 12.25 Rear seats— —Folding down rear seats (vehicles without third seats) CY13107 CY13163 CY13093 BEFORE FOLDING DOWN REAR SEAT If you are using a trash holder, lower 1. Lower the head restraint to the lowe- st position. Stow the rear center seat belt buckle as shown in the illustration.
Page 66 07 12.25 CY13131 CY13132 CY13082 2. Swing the bottom cushion up by 3. Push the lock release button and WHEN RETURNING THE SEATBACK pulling the lock release strap. fold down the seatback. If you cannot raise the seatback because Each bottom cushion can be swung up This will enlarge the luggage compartment of the locked seat belt, do not try to force separately.
Page 67: Rear Seat Precautions
07 12.25 —Rear seat precautions (vehicles with third seats) CAUTION CAUTION The third seats have a maximum capacity of two belted occupants When returning seats to their original Adjustment should not be made who do not exceed 150 cm (59 in.) position, observe the following pre- while the vehicle is moving.
Page 68 07 12.25 —Adjusting rear seats (vehicles with third seats) —Tumbling second seats SEATBACK ANGLE ADJUSTING LEVER Lean forward and pull the lock release lever. Then lean back to the desired angle and release the lever. CY13199 CAUTION CY13200 Avoid reclining seatback more than needed.
Page 69 07 12.25 CY13201 CY13202 CY13203 TUMBLING SECOND SEATS WHEN RETURNING SECOND SEATS If you cannot raise the seatback because of the locked seat belt, do not try to force Lower the head restraints to the lowest Push the knob to unlock the seat, it.
Page 70 07 12.25 —Folding up third seats CAUTION To prevent death or serious injury in a collision or sudden stop: When tumbling seats returning Do not sit on or place anything on seats to their original positions, ob- the folded seatback or tumbled seat serve the following to prevent death while driving.
Page 71 07 12.25 CY13230 CY13206 CY13207 2. Make sure the shoulder belt passes FOLDING UP THIRD SEATS 2. Unlock the seat leg by pulling the through the hanger. handle behind the seat, and swing 1. Lower the head restraint to the low- the whole seat up and sideward.
Page 72 07 12.25 CY13255 CY13256 CY13257 3. Stow the seat leg in the back of the 4. Remove the seat anchor covers from When returning the third seat to its origi- seat cushion. Take the holding strap the back of the seat cushion, and nal position, stow the holding strap in the out of its holder, and attach the install them over the seat anchors.
Page 73 07 12.25 —Removing third seats CAUTION When folding up seats or returning seats to their original positions, ob- serve the following to prevent death CY13248 CY13230 or serious injury: Do not fold up or return the seat while the vehicle is moving. careful seat against a person or drop it on your-...
Page 74 07 12.25 CY13206 CY13210 CY13211 REMOVING THIRD SEATS 2. Unlock the seat leg by pulling the 3. Remove the cover and push the seat handle behind the seat, and lift the lock release lever outward to unlock 1. Lower the head restraint to the low- whole seat up.
Page 75 07 12.25 REINSTALLING THIRD SEATS 1. Remove the seat anchor covers from the floor and install them in the back of the seat cushion. Hold the seat and engage the seat striker to the seat lock, then place the seat on CY13258 the floor.
Page 76 07 12.25 When reinstalling the seat, be care- ful not to hit the seat against your- self or the vehicle. To prevent death or serious injury in a collision or sudden stop: CY13213 CY13214 Do not sit on or place anything on the folded seatback while driving.
Page 77: Head Restraints
07 12.25 Head restraints For your safety and comfort, adjust the head restraint before driving. To raise: Pull it up. To lower: Push it down while pressing the lock release button. CY13109 CY13238 Front head restraints—You can also move the head restraint forward or backward. If such adjustment is desired, pull or push the base of the head restraint.
Page 78: Armrest
07 12.25 Armrest Seat heaters CAUTION Adjust the center of the head re- straint so that it is closest to the top of your ears. CY13137 CY13193 After adjusting the head restraint, make sure it is locked in position. Do not drive with the head re- straints removed.
Page 79: Seat Belts
07 12.25 Seat belts— —Seat belt precautions Toyota strongly urges that the driver and NOTICE CAUTION passengers in the vehicle be properly re- strained at all times with the seat belts z Do not put unevenly weighed ob- Occupants must use caution when op- provided.
Page 80 Check for cuts, fraying, and loose to suffer serious injury or death in parts. Damaged parts should be re- Pregnant woman. Toyota recommends the the event of sudden braking or a col- placed. disassemble use of a seat belt. Ask your doctor for lision.
Page 81 It also may normally, immediately contact your lock if you lean forward too quickly. A Toyota dealer. Do not use the seat slow, easy motion will allow the belt to until the seat belt is fixed, because extend, and you can move around freely.
Page 82 07 12.25 CAUTION CAUTION Both high−positioned lap belts and Always make sure the shoulder belt loose−fitting belts could cause is positioned across the center of death or serious injuries due to your shoulder. The belt should be CY13007 sliding under the lap belt during a kept away from your neck, but not collision or other unintended event.
Page 83 07 12.25 —Stowing rear seat belt buckles CY13164 CY13107 CY13249 Rear center seat—vehicles without third Third seats To release the belt, press the buckle seats release button and allow the belt to rear seat belt buckles can be retract. stowed when not in use. If the belt does not retract smoothly, pull Seat belt buckle must be stowed before it out and check for kinks or twists.
Page 84: Seat Belt Extender
If the indicator light indi- Please contact your local Toyota dealer to CY13241 cates “OFF”, disconnect the extend- order the proper required length for the er tongue from the seat belt buckle, extender.
Page 85 When releasing the seat belt, press on normally, immediately contact your the buckle release button on the extender, Toyota dealer. Do not use the seat not on the seat belt. This helps prevent until the seat belt is fixed, because...
Page 86: Seat Belt Pretensioners
07 12.25 —Seat belt pretensioners The seat belt pretensioner will not activate if no passenger is detected in the front passenger seat by the front passenger occupant classification system. However, front passenger’s seat belt pretensioner may activate if luggage is put CY13018 CY13294 on the seat, or the seat belt is buckled up...
Page 87 When the seat belt pretensioners are acti- sult in death or serious injury. Con- vated, an operating noise may be heard CY13293 sult your Toyota dealer about any and a small amount of non−toxic gas may repair and modification. be released. This does not indicate that Do not use tires or wheels other a fire is occurring.
Page 88 Contact your conds. This means the seat belt preten- z Attachment of a grille guard (bull Toyota dealer as soon as possible. sioners are operating properly. bar, kangaroo bar, etc.), snowplow, The light does not come on when the winches or any other equipment to engine switch is turned to the “ON”...
Page 89: Srs Airbags
CY13064 CY13019 In the following cases, contact your Toyota The SRS (Supplemental Restraint Sys- dealer as soon as possible: tem) front airbags are designed to pro- vide further protection for the driver...
Page 90 The driver and front passenger can child restraint system. Toyota The SRS front passenger airbag will not be killed or seriously injured by the strongly recommends that all in- activate if there is no passenger sitting in inflating airbags if they do not wear fants and children be placed in the the front passenger seat.
Page 91 07 12.25 The SRS front airbags are designed to deploy in severe (usually frontal) colli- sions where the magnitude and duration of the forward deceleration of the ve- hicle exceeds the designed threshold Hitting a curb, edge Falling into or of pavement or jumping over level.
Page 92 07 12.25 8. Driver’s seat position sensor Deployment of the airbags happens in a fraction of a second, so the airbags must 9. Airbag sensor assembly inflate with considerable force. While the 10. Airbag module for driver system is designed to reduce serious inju- (airbag and inflator) ries, primarily to the head and chest, it The airbag sensor assembly consists of a...
Page 93 All vehicle occupants be properly Do not sit on the edge of the seat Toyota strongly recommends that all restrained using the available seat or lean against the dashboard when infants and children be placed in belts.
Page 94 Toyota dealer. It may dan- the front end they are projected rearward by the gerously interfere with the SRS front force of the deploying airbags.
Page 95 149 in Sec- tion 1−6.) This indicator comes on when the en- In the following cases, contact your Toyota If any of the following conditions occurs, gine switch is turned to the “ON” posi- dealer as soon as possible: this indicates a malfunction of the airbags tion.
Page 96: Curtain Shield Airbags
Do not disconnect the battery cables belts to help reduce injury by inflating. before contacting your Toyota dealer. The SRS side airbags help reduce injuries mainly to the driver’s or front passenger’s CY13073 chest.
Page 97 07 12.25 Roll sensing function: CAUTION Do not allow anyone to lean his/her In response to a vehicle rollover, the cur- head or any part of his/her body tain shield airbags on both sides work The SRS side airbag and curtain against the door or the area of the with the seat belts to help reduce injury shield airbag system is designed...
Page 98 CY13310 should be properly secured using a child restraint system. Toyota strongly recommends that all in- fants and children be placed in the rear seats of the vehicle and prop- Collision from the front erly restrained. The rear seats are Vehicle rollover the safest for infants and children.
Page 99 07 12.25 Collision from CY13071 CY13311 CY13229 Collision from the front the rear The angle of Skidding vehicle vehicle tip−up hitting a curb is marginal stone Pitch end over end The curtain shield airbags may not acti- The curtain shield airbags may inflate The curtain shield airbags are not gen- vate if the vehicle is subjected to a if the angle of vehicle tip−up is margin-...
Page 100: Srs Warning Light
07 12.25 8. Front passenger’s seat belt buckle switch 9. Airbag sensor assembly The SRS side airbag and curtain shield Hitting a curb, edge Falling into or airbag system is controlled by the airbag of pavement or jumping over CY13232 CY13278 sensor assembly.
Page 101 07 12.25 When the airbags inflate, they produce a CAUTION fairly loud noise and release some smoke and residue along with non−toxic gas. This SRS side airbags and curtain shield does not indicate a fire. This smoke may airbags inflate with considerable remain inside the vehicle for some time,...
Page 102 07 12.25 CY13294 CY13026 CY13024 Make sure the “RSCA OFF” indica- Do not allow anyone to get his/her Do not allow anyone to kneel on tor light is off. The curtain shield head closer to the area where the the passenger seat, facing the pas- airbags will not inflate in a vehicle side airbag and curtain shield air- senger’s side door, since the side...
Page 103 07 12.25 CY13233 CY13069 CY13234 Do not allow anyone to get his/her Do not attach a cup holder or any Do not attach a microphone or any head hands windows other device or object on or around other device or object near the area since curtain shield...
Page 104 Toyota dealer. It may dan- injury. When hang clothes,...
Page 105 “ON” posi- this indicates a malfunction of the airbags tion. It goes off after about 6 seconds. or seat belt pretensioners. Contact your This means the SRS side airbags and Toyota dealer as soon as possible. curtain shield airbags operating The light does not come on when the properly.
Page 106: Front Passenger Occupant Classification System
07 12.25 —Front passenger occupant classification system In the following cases, contact your Toyota Your vehicle is equipped with a front dealer as soon as possible: passenger occupant classification sys- tem. This system detects the conditions Any of the SRS side airbags and cur- 1—4 in the table on page 93 and based...
Page 107 07 12.25 If the front passenger occupant classifica- The front passenger occupant classifi- tion system determines that a person of cation indicator light will indicate “ON” adult size sits in the front passenger seat and “OFF” when the engine switch is but the “OFF”...
Page 108 07 12.25 Condition and operation in the front passenger occupant classification system Indicator/warning light Devices Condition detected by Front Curtain shield Front Side airbag Front the front passenger passenger Front airbag in the SRS warning passenger’s on the front passenger’s occupant classification occupant passenger...
Page 109 07 12.25 CAUTION Do not recline the front passenger Wear the seat belt properly. seatback so far that it touches a Make sure the front passenger’s To avoid potential death or serious second seat. This may cause the seat belt tab has not been left in- injury when the front passenger occu- “OFF”...
Page 110: Roll Sensing Of Curtain Shield Airbags Off Switch
“—SRS side airbags and curtain tion of the detection system. In this bags off switch (“RSCA OFF” switch) shield airbags” on page 81 in this Sec- case, contact your Toyota dealer im- can turn off the curtain shield airbags tion.) mediately.
Page 111: Child Restraint
07 12.25 Child restraint— —Child restraint precautions Toyota strongly urges the use of ap- CAUTION Toyota strongly urges use of propriate child restraint systems for proper child restraint system which children. Before normal driving, make sure conforms to the size of the child, The laws of all 50 states in the U.S.A.
Page 112: Child Restraint System
07 12.25 —Child restraint system A child restraint system for a small A forward−facing child restraint sys- Do not use the seat belt extender child or baby must itself be properly should allowed when installing child restraint restrained on the seat with the lap por- installed on front passenger system on the front or rear passen-...
Page 113: Types Of Child Restraint System
07 12.25 —Types of child restraint system Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat CY13138 CY13140 Install the child restraint system following the instructions provided by its manufac- turer.
Page 114: Installation
07 12.25 —Installation with seat belt CY13141 CY13034 CY13035 (A) INFANT SEAT INSTALLATION CAUTION Do not install a child restraint sys- An infant seat must be used in rear− tem on the second (or third) seat if facing position only. Never install a rear−facing child re- it interferes with the lock mecha- straint system on the front passen-...
Page 115 To install the infant seat: 2. Fully extend the shoulder belt to put it Contact your Toyota dealer immedi- in the lock mode. When the belt is 1. Run the lap and shoulder belt through ately.
Page 116 07 12.25 CY13158 CY13159 CY13116 3. While pressing the infant seat firmly To remove the infant seat: CAUTION against the seat cushion and seatback, Press the buckle release button and allow let the shoulder belt retract as far as the belt to retract completely. The belt will Push and pull the child restraint sys- it will go to hold the infant seat secure- move freely again and be ready to work...
Page 117 07 12.25 Install the child restraint system on the 6. While pressing convertible seat front passenger seat only when it is un- firmly against the seat cushion and avoidable. Your vehicle is equipped with a seatback, let the shoulder belt retract front passenger occupant...
Page 118 Never install a rear−facing child re- child restraint system and contact your senger airbag and side airbag on straint system on the front passen- Toyota dealer. front passenger seat could ger seat even if the front passenger deploy.
Page 119 07 12.25 Do not allow the child to lean his/ her head or any part of his/her body against the door or the area of the seat, front or rear pillar or roof side rail from which the side CY13043 CY13044 airbags or curtain shield airbags deploy even if the child is seated in...
Page 120 To install the forward−facing convertible 2. Fully extend the shoulder belt to put it Contact your Toyota dealer immedi- seat: in the lock mode. When the belt is ately. install child then retracted even slightly, it cannot 1.
Page 121 07 12.25 CY13145 CY13146 CY13118 3. While pressing convertible seat To remove the convertible seat: CAUTION firmly against the seat cushion and Press the buckle release button and allow seatback, let the shoulder belt retract the belt to retract completely. The belt will Push and pull the child restraint sys- as far as it will go to hold the convert- move freely again and be ready to work...
Page 122 07 12.25 Do not allow the child to lean his/ her head or any part of his/her body against the door or the area of the seat, front or rear pillar or roof side rail from which the side CY13147 CY13051 airbags or curtain shield airbags deploy even if the child is seated in...
Page 123 Always make sure the shoulder belt child from death or serious injury. is positioned across the center of Contact your Toyota dealer immedi- child’s shoulder. The belt should be ately. install child CY13119 kept away from child’s neck, but...
Page 124 07 12.25 —Using a top strap (vehicles without third seats) Anchor brackets CY13118 CY13306 CY13307 Symbol To remove the booster seat: Follow the procedure below for a child Use the anchor brackets behind the rear Press the buckle release button and allow restraint system that requires the use seatbacks to attach the top strap.
Page 125 07 12.25 CY13096 CY13188 CY13152 TO USE THE ANCHOR BRACKET: 2. Raise the anchor bracket. 3. Fix the child restraint system with the seat belt. 1. Remove the head restraint. Latch hook onto the anchor bracket and tighten the top strap. The anchor bracket is only designed to secure the top strap.
Page 126 07 12.25 CAUTION Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing CY13099 CY13153 and pulling it in different directions. Follow all the installation instructions provided by its manufacturer. 4.
Page 127 07 12.25 —Using a top strap (vehicles with third seats) Anchor brackets CY13308 CY13242 CY13219 Symbol Follow the procedure below for a child Use the anchor brackets behind the sec- TO USE THE ANCHOR BRACKET: restraint system that requires the use ond seatbacks to attach the top strap.
Page 128 07 12.25 CAUTION Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing CY13220 CY13221 and pulling it in different directions. Follow all the installation instructions provided by its manufacturer. 2.
Page 129 07 12.25 —Installation with child restraint lower anchorages (vehicles without third seats) CY13222 CY13175 CY13262 4. Replace the head restraint. Lower anchorages for the child restraint systems complying with the FMVSS225 Close the anchor bracket cover when the CMVSS210.2 specifications anchor bracket is not used.
Page 130 07 12.25 CHILD RESTRAINT SYSTEM CAUTION INSTALLATION 1. Widen the gap between the seat When using the lower anchorages cushion and seatback slightly and for the child restraint system, be confirm the position of the lower an- sure that there are no irregular ob- chorages near the button on the jects around the anchorages or that seatback.
Page 131 07 12.25 —Installation with child restraint lower anchorages (vehicles with third seats) 1st lock 5th lock position position CY13223 CY13289 CY13291 Lower anchorages for the child restraint CHILD RESTRAINT SYSTEM 2. Take off the cover on the seat cush- systems complying with the FMVSS225 INSTALLATION ion.
Page 132 07 12.25 3. Widen the slits of the seat cushion slightly and confirm the position of the lower anchorages near the but- ton on the seatback. 4. Type A—Latch the hooks of lower straps onto anchorages tighten the lower straps. Type B—Latch the buckles onto the anchorages.
Page 133 07 12.25 CAUTION When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- CY13227 jects around the anchorages or that the seat belt is not caught. Push and pull the child restraint system in different directions to be sure it is secure.
Page 134 07 12.25 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Steering wheel and Mirrors Tilt steering wheel ......... . Tilt and telescopic steering wheel .
Page 135: Tilt Steering Wheel
07 12.25 Tilt and telescopic steering Tilt steering wheel wheel CAUTION Do not adjust the steering wheel while the vehicle is moving. Doing so may cause the driver to mishan- CY13305 CY13303 dle the vehicle and an accident may occur resulting in death or serious injuries.
Page 136: Outside Rear View Mirrors
07 12.25 Outside rear view mirrors— CAUTION Do not adjust the steering wheel while the vehicle is moving. Doing so may cause the driver to mishan- CY13304 CY13009 dle the vehicle and an accident may occur resulting in death or serious injuries.
Page 137: Power Rear View
07 12.25 —Power rear view mirror control On some models, the outside rear view NOTICE mirrors are rain clearing mirrors that clear the driver’s rear view when it rains. (For If ice should jam the mirror, do not details, see “Rain clearing mirrors” on operate the control or scrape the mir- page 419 in Section 5.) ror face.
Page 138: Anti−Glare Inside Rear View Mirror
07 12.25 Anti−glare inside rear view —Folding rear view mirrors mirror CAUTION Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- CY13011 CY13012 hicle and an accident may occur re- sulting in death or serious injuries.
Page 139: Auto Anti−Glare Inside Rear View Mirror
07 12.25 Auto anti−glare inside rear view mirror In automatic function mode, if the mirror detects light from the headlights of the vehicle behind you, the mirror surface darkens slightly to reduce the reflected light. To turn off and on the automatic function, CY13312 CY13313 push the “...
Page 140: Rear Side−View Mirrors
07 12.25 Rear side−view mirrors Sun visors— Rear side−view mirrors are useful as a secondary means of checking the area to the rear of the vehicle. Carefully check the area to the rear of the vehicle by either looking directly or using both outside and inside rear view mirrors.
Page 141 07 12.25 To block out glare, move the sun visor. CAUTION To block out glare from the front—Swing down the main sun visor (position 1). Type A—Do not extend the plate at To block out glare from the side—Swing the end of the sun visor when the down the main sun visor, remove it from visor is in the position 1.
Page 142: Vanity
07 12.25 —Vanity mirrors To use the vanity mirrors, swing down the main sun visor and slide the cover. Type A— The vanity light comes on when you slide the cover. CY13160 To prevent the battery being discharged, the light will automatically turn off when the key is removed for 30 minutes or more.
Page 143 07 12.25...
Page 144 07 12.25 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Lights, Wipers and Defogger Headlights and turn signals ........Emergency flashers .
Page 145: Headlights And Turn Signals
For details, contact your ed immediately when entering a dark tun- Toyota dealer. nel, parking structure, etc. Automatic light cut off system Position 1 or position 3 with the tail lights on—...
Page 146 (position 3)—Pull the lever all the way NOTICE This DRL system can be disabled. For back. The high beam headlights turn off details, contact your Toyota dealer. To prevent the battery from being dis- when you release the lever. charged, do not leave the lights on...
Page 147 07 12.25 Headlights and turn signals (without automatic light control system) If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out. CY14014 CY14038 For the U.S.A. TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position...
Page 148 This DRL system can be disabled. For switch in the “ACC” or “LOCK” position. details, contact your Toyota dealer. Position 2— The lights automatically turn off after 30 seconds when all the side doors and back door are closed with the engine switch in the “ACC”...
Page 149 07 12.25 If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out. CY14016 CY14017 High−Low beams—For high beams, turn TURN SIGNALS the headlights on and push the lever away To signal a turn, push the headlight/ from you (position 1).
Page 150: Emergency Flashers
07 12.25 Emergency flashers Instrument panel light control NOTICE To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running. CY14042 CY14043 To turn on the emergency flashers, To adjust the brightness of the instru- push the switch.
Page 151: Front Fog Lights
07 12.25 Interior light (without rear Front fog lights seat entertainment system) ILLUMINATED ENTRY SYSTEM Door linked operation—When the switch is in the “DOOR” position and any of the side doors and back door is opened, the light will come on. After all the side doors and back door are closed, the light re- CY14044 CY14022...
Page 152: Entertainment System
For details, contact your Door linked operation—When the switch is Toyota dealer. in the “DOOR” position and any of the Cancelling the door key or the wireless side doors and back door is opened, the remote control transmitter linked opera- light will come on.
Page 153: Personal Lights
Personal lights Luggage compartment light The following adjustments can be made in this system. For details, contact your Toyota dealer. Cancelling the door key or the wireless remote control transmitter linked opera- tion CY14004 CY14005 Changing the duration of lighting...
Page 154: Engine (Ignition) Switch Light
15 seconds before fading out. closed when the engine switch is in the “ACC” or “ON” position. The following adjustments can be made in this system. For details, contact your All the side doors and back door are Toyota dealer. closed and locked.
Page 155: Running Board Lights
For details, contact your the light will automatically turn off when Toyota dealer. the key is removed and the door is left opened for 30 minutes or more. Cancelling the door key or the wireless remote control transmitter linked opera-...
Page 156: Windshield Wipers And Washer
07 12.25 Back window wiper and Windshield wipers and washer washer To squirt washer fluid, pull the lever toward you. If the windshield wipers are off, they will operate a couple of times after the washer squirts. CY14040 CY14041 For instructions on adding washer fluid, see “Adding washer fluid”...
Page 157: Back Window And Outside Rear View Mirror Defoggers
07 12.25 Back window and outside rear view mirror defoggers For instructions on adding washer fluid, The system will automatically shut off af- see “Adding washer fluid” on page 453 in ter the defoggers have operated about 15 Section 7−3. minutes.
Page 158 07 12.25 NOTICE When cleaning the inside of the back window, be careful not to scratch or damage the heater wires or connec- tors.
Page 159 07 12.25...
Page 160 07 12.25 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators Fuel gauge ..........Engine coolant temperature gauge .
Page 161: Fuel Gauge
Fill the fuel tank immediately. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as Low fuel level warning light soon as possible.
Page 162: Tachometer
07 12.25 Tachometer Idling for a long period with the air NOTICE conditioning on in stop−and−go traffic. Do not let the indicator needle get Towing a trailer. into the red zone. This may cause NOTICE severe engine damage. CY15003 z Do not remove the thermostat in the engine cooling system as this may cause the engine to overheat.
Page 163: Odometer And Two Trip Meters
07 12.25 Odometer and two trip meters 3. Trip meter reset knob—Resets the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the CY15009 odometer to trip meter A to trip meter B, then back to the odometer each...
Page 164: Service Reminder Indicators And Warning Buzzers
07 12.25 Service reminder indicators and warning buzzers If the indicator or buzzer comes on... Do this. If parking brake is off, stop immediately and contact Toyota dealer. (indicator and buzzer) Fasten driver’s seat belt. (indicator and buzzer) Fasten front passenger’s seat belt.
Page 165 If the indicator or buzzer comes on... Do this. Replace engine oil. Take vehicle to Toyota dealer. If brake system warning light is also on, stop immediately and contact Toyota dealer. If the light flashes, take vehicle to Toyota dealer.
Page 166 07 12.25 If the indicator or buzzer comes on... Do this. Add washer fluid. Key reminder buzzer Remove key. Release parking brake. Parking brake reminder buzzer...
Page 167 It is dangerous to continue driving mal if it turns off after a while. a safe place and contact your Toyota normally when the brake fluid level is dealer. Depressing the brake pedal repeatedly low.
Page 168 07 12.25 The buzzer can be disabled. For details, contact your Toyota dealer. (b) Driver’s Seat Belt Reminder Light (c) Front Passenger’s Seat Belt and Buzzer Reminder Light and Buzzer The light and buzzer act as a reminder to The light and buzzer act as a reminder to buckle up the driver’s seat belt.
Page 169 “ON” posi- and stop the engine immediately. Call a If the lamp remains on, or the lamp tion, and goes off when the engine is Toyota dealer or qualified repair shop for comes on while driving, first check the started. assistance.
Page 170 Have your vehicle For details, see “Emissions Inspection and this light illuminates for about 3 seconds checked by your Toyota dealer as soon as Maintenance (I/M) programs” on page 426 and then flashes for about 12 seconds possible.
Page 171 Contact your 1. Turn the engine switch to the “ACC” or Toyota dealer as soon as possible to “LOCK” position with odometer Anti−lock brake system...
Page 172 The light flashing warns that there is a buckle switch, front passenger occupant In the following cases, contact your Toyota problem somewhere in the following. classification system and indicator light, dealer: Vehicle stability control system front passenger’s seat belt buckle switch,...
Page 173 If the light does not go off, call a vehicle speed of 5 km/h (3 mph) or more. Toyota dealer or qualified repair shop for If the warning light comes on after blink- Stop the vehicle and release the parking assistance.
Page 174: Height Control
If any service reminder indicator or warn- All the service reminder indicators ex- ing buzzer does not function as described cept the open door warning light should above, have it checked by your Toyota come on. dealer as soon as possible. The following service reminder indica-...
Page 175 07 12.25...
Page 176: Height Control
07 12.25 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Engine (ignition) switch, Transmission and Parking brake Engine (ignition) switch ........Automatic transmission .
Page 177: Engine (Ignition) Switch
07 12.25 Engine (ignition) switch “LOCK”—Engine is off and the steering NOTICE wheel is locked. The key can be re- moved only at this position. Do not leave the engine switch in the “ON” position if the engine is not You must push in the key to turn engine running.
Page 178: Automatic Transmission
07 12.25 Automatic transmission Your automatic transmission has a shift lock system to minimize the possibility of incorrect operation. This means you can only shift out of “P” position when the brake pedal is depressed (with the engine switch in “ON” position). (a) Selector lever The shift position is also displayed on the instrument cluster.
Page 179 07 12.25 (b) Normal driving 2. With your foot holding down the brake Vehicles with multi−mode control— pedal, shift the selector lever to “D”. 1. Start the engine as instructed in “How Always use the “D” position for better fuel to start the engine”...
Page 180 07 12.25 (c) Using engine braking 4.7 L V8 (2UZ−FE) engine 4.7 L V8 (2UZ−FE) engine To use engine braking, you can downshift Four−wheel drive control switch Four−wheel drive control switch the transmission as follows: knob at “H4” knob at “H4” 139 km/h (86 mph) 94 km/h (58 mph) Shift into the “4”...
Page 181 07 12.25 4.7 L V8 (2UZ−FE) engine (d) Using “3”, “2” and “L” positions NOTICE Four−wheel drive control switch The “3”, “2” and “L” positions are used for z Be careful not to over−rev the en- knob at “H4” strong engine braking as described pre- gine.
Page 182 07 12.25 (f) Parking Four−wheel drive models z Do not continue hill climbing or 1. Bring the vehicle to a complete stop. hard towing for a long time in the 4.0 L V6 (1GR−FE) engine “3”, “2” or “L” position. This may 2.
Page 183: Four−Wheel Drive System
07 12.25 Four−wheel drive system (full−time four−wheel drive models)— (a) Four−wheel drive control (g) Good driving practice (h) If you cannot shift the selector le- ver out of “P” position If the transmission repeatedly shifts up and down between fourth gear and If you cannot shift the selector lever from overdrive when climbing a gentle slope, the “P”...
Page 184 07 12.25 Use the four−wheel drive control switch “L4” (low speed position) and center NOTICE knob and center differential lock switch differential unlocked: Four−wheel drive control switch knob at “L4”, center differ- to select the transfer and center differ- As soon as the center differential lock ential modes.
Page 185 “Cruise switch knob fully counterclockwise. control” on page 203 in Section 1−7. If the indicator blinks even if doing so, contact your Toyota dealer as soon as possible. There may be a trouble in the center differential lock system.
Page 186 “N” and operate the switch knob again. If the indicator continues to blink even if doing so, contact your Toyota dealer as soon as possible. There may be a trouble in the four−wheel drive system.
Page 187 07 12.25 The center differential can be locked or “H2” (high speed position, two−wheel “L4” (low speed position, four−wheel unlocked by pushing the center differential drive): Multi−mode control switch knob at drive) and center differential unlocked: lock switch. “H2” Multi−mode control switch knob at “L4”, center differential unlocked Use the center differential lock system if Use this for normal driving on dry hard−...
Page 188 “Cruise control” on page 203 in Section 1−7. If the indicator blinks even if doing so, contact your Toyota dealer as soon as possible. There may be a trouble in the center differential lock system.
Page 189 If the indicator light continues to blink vehicle to a complete stop with the brake If the four−wheel drive indicator and the even if doing so, contact your Toyota pedal held down with your foot, shift the center differential lock indicator lights con- dealer as soon as possible.
Page 190: Traction Control System
If the indicator continues to blink even if Under certain slippery road condi- doing so, contact your Toyota dealer as tions, full traction of the vehicle and soon as possible. There may be a trouble power to the rear wheels cannot be in the four−wheel drive system.
Page 191 Toyota dealer. The brake actuator temperature increases during continuous operation of the traction control system, the “AUTO LSD” system, the vehicle stability control system and the hill−start assist control system such...
Page 192 In the following cases, contact your Toyota When you push and hold the “VSC OFF” dealer: switch for 3 seconds or more with the...
Page 193: Active Traction Control System
CY16073 to “ON”. If the indicator light does not come on when the engine switch is turned CAUTION on, contact your Toyota dealer. Under certain slippery road condi- The brake actuator temperature increases tions, full traction of the vehicle and...
Page 194 In the following cases, contact your Toyota dealer: The warning light does not come on after the engine switch is turned to “ON”.
Page 195: Auto Lsd" System
07 12.25 “AUTO LSD” system (two−wheel drive and muti−mode four−wheel drive models) NOTICE Do not use the “AUTO LSD” system in conditions other than the above. A much greater steering effort and more careful cornering control will be re- CY16070 CY16075 quired.
Page 196 The the engine switch is turned to “ON”, con- system will be automatically restored after tact your Toyota dealer. a short time and the slip indicator light goes off.
Page 197 07 12.25 When the system is normal and the en- In the following cases, contact your Toyota gine switch is turned to the “ON” position, dealer: the light will come on and will go off after The warning light does not come on a few seconds.
Page 198: Vehicle Stability Control System
When replacing the tires or wheels, the brake pedal will become hard at an contact your Toyota dealer. (See earlier position than usual. However, the “Checking and replacing tires” on brakes will respond to the pedal force if page 443 in Section 7−2.)
Page 199 07 12.25 In the following cases, contact your Toyota dealer: The indicator light does not come on when the engine switch is turned to “ON”. CY16061 CY16075 The indicator light remains on after the engine switch is turned to “ON”.
Page 200 “VSC OFF” warning light come on for a few seconds when the engine switch is turned to “ON”. If the Vehicle stability control system In the following cases, contact your Toyota indicator lights do not come on when the dealer: Traction control system engine switch is turned to “ON”, contact...
Page 201: Downhill Assist Control System
“H4” position. abling the system to operate more effec- If the indicator light does not come on tively. when the switch is pushed, contact your Toyota dealer.
Page 202 “ON”. If any of the indicator knob may be in the “H2” or “H4” position. lights does not come on when the engine switch is turned on, contact your Toyota If the indicator light does not come on CY16073 dealer.
Page 203 In the following cases, contact your Toyota If the “VSC OFF” warning light flashes, dealer: there may be an abnormality in any of the...
Page 204: Hill−Start Assist Control System
“ON”. If the indicator light does not uphill slope. come on when the engine switch is turned on, contact your Toyota dealer.
Page 205 07 12.25 Keep in mind the following when driv- If the system continues to operate, the ing. buzzer sound changes from intermittent to continuous. (The continuous buzzer The hill−start assist control system op- sounds for about 3 seconds.) erates for 5 seconds maximally. If both the brake and accelerator pedals re- At this time, the slip indicator light will main undepressed for longer than 5...
Page 206: Rear Height Control Air Suspension
(a) Vehicle height modes In the following cases, contact your Toyota “N” (normal) mode— dealer: The vehicle height in this mode is stan- The warning light does not come on dard.
Page 207 07 12.25 “LO” (low) mode— When selecting a mode, there is a ve- If the vehicle is moved to its usual loca- hicle speed limit. Refer to the following tion or the ice is removed and the height The vehicle height is about 20 mm (0.8 table.
Page 208 07 12.25 To change the “LO” mode to “HI”, push NOTICE the switch twice. It takes about 30 sec- onds until the “LO” mode changes to the z If the vehicle height is changed fre- “HI” mode. quently when the vehicle is heavily loaded, the compressor may over- Selecting the “N”...
Page 209 07 12.25 (d) Turning off the rear height control CAUTION air suspension To turn off the rear height control air If you drive through deep water over suspension with the vehicle stopped, about 700 mm (28 in.) in depth, put push “HEIGHT CONTROL...
Page 210 07 12.25 z If your vehicle gets ditched, turn off the rear height control air suspen- sion with the “HEIGHT CONTROL OFF” switch. Otherwise, the vehicle height may change because of the CY16018 CY16019 automatic leveling function resulting in an unexpected accident. (e) Height control indicator lights If you change the vehicle height mode, the indicator lights change as follows:...
Page 211 In this case, even if the vehicle is moved the vehicle after off−road driving, the ve- vehicle to your Toyota dealer as soon as to its usual location or the ice is removed hicle height is lowered slightly as the ve- possible and have it checked.
Page 212: Tire Pressure Warning System
Type A Adjust the Tire inflation tire pressure is inflation pressure Have the Tire pressure ON after system warning blinking for checked at system CY16068 1 minute your Toyota malfunction dealer Type B...
Page 213 If the tire is flat, change to light will turn off after a few minutes. the spare tire and have the flat tire repaired by the nearest Toyota deal- Avoid abrupt maneuvering and brak- ing. If the vehicle tires deteriorate, you could lose control of the steer- ing wheel or the brakes.
Page 214 Toyota dealer under−inflation has not reached the or an authorized tire dealer. The level to trigger illumination of the...
Page 215 07 12.25 TIRE PRESSURE WARNING If a radio set at similar frequencies is LIGHT COMES ON AFTER BLINKING in use in the vehicle. FOR 1 MINUTE... If a window tint that affects the radio If the tire pressure warning light comes wave signals is installed.
Page 216 07 12.25 If non−genuine Toyota wheels are used. For vehicles sold in U.S.A. NOTICE: If tire chains are used. This equipment has been tested and This device complies with Part 15 of the If the spare tire is in a location subject found to comply with the limits for a FCC Rules.
Page 217: Parking Brake
ID code of tire pres- Consult the dealer or an experienced sure warning valve and transmitter. Have radio/TV technician for help. the ID code registered by your Toyota FCC WARNING: dealer. Changes modifications...
Page 218: Cruise Control
07 12.25 Cruise control The cruise control is designed to main- CAUTION tain a set cruising speed without requir- ing the driver to operate the accelera- Before driving, be sure the parking tor. Cruising speed can be set to any brake is fully released and the park- speed above 40 km/h (25 mph).
Page 219 07 12.25 you need acceleration—for example, CAUTION when passing—depress accelerator pedal enough for the vehicle to exceed To avoid accidentally engaging the the set speed. When you release it, the cruise control, turn the system off vehicle will return to the speed set prior when it is not in use.
Page 220 To decrease the vehicle celled, the cruising speed can be resumed speed, reset to a slower speed with the If this is the case, contact your Toyota by pushing the lever up in the “+ RES” cruise control lever or depress the brake dealer and have your vehicle inspected.
Page 221 07 12.25...
Page 222 07 12.25 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Audio system Reference ..........Using your audio system .
Page 223: Reference
(with XMr Satellite Radio controller) controller) ∗ ∗ : Use of satellite radio requires XM : Use of satellite radio requires XM tuner and service. Contact your Toyota tuner and service. Contact your Toyota dealer for details. dealer for details.
Page 224: Using Your Audio System
07 12.25 Using your audio system— —Some basics CAUTION This section describes some of the basic features on Toyota audio systems. Some vehicle sold U.S.A. information may not pertain to your sys- Canadas: tem. Part 15 of the FCC Rules...
Page 225 Satellite Radio in on and off. To listen to a satellite radio broadcast in order to receive satellite broadcast pro- your vehicle, an additional genuine Toyota ∗ Push “AM”, “FM1”, “FM2”, “FM”, “AM·SAT” gramming in the vehicle. Additional activa- satellite receiver and antenna (or equiva- or “DISC·AUX”...
Page 226 Satellite tuner technology notice: your own system. levels is also important. Toyota’s satellite radio tuners are awarded Keep in mind that if you are listening to Type Approval Certificates from XM Sat- a stereo recording or broadcast, changing ellite Radio Inc.
Page 227 07 12.25 YOUR COMPACT DISC PLAYER (type 1) When you insert a disc, gently push it in with the label side up. The compact disc player will play from track 1 through to the end of the disc. Then it will play from track 1 again.
Page 228 07 12.25 —Controls and features "Type 1 CY17064y...
Page 229 07 12.25 Details of specific buttons, controls and 1 2 3 4 5 6 (Preset buttons) (Reverse/Fast−forward button) features are described in the alphabetical These buttons are used to preset and list that follows. Push and hold “ ” (preset button 6) or tune in radio stations.
Page 230 MP3/WMA in use, “AUX” will appear on the display. When playing a disc featuring both audio data disc. data (CD−DA) and MP3/WMA files, audio If the malfunction still exists, take your data (CD−DA) is played. vehicle to your Toyota dealer.
Page 231 07 12.25 PWR·VOL (Power and Volume) With compact disc changer only— RPT (Repeat) Push “PWR·VOL” to turn the audio system To play all the tracks in the magazine in Compact disc player on and off. Turn “PWR·VOL” to adjust the random order: There are two repeat features—you can volume.
Page 232 07 12.25 MP3/WMA player SCAN Compact disc player There are two repeat features—You can Radio There are two scan features—you can ei- repeat a single file or an entire folder. ther scan the tracks on a specific disc or You can either scan all the frequencies on scan the first tracks of all the discs in the Repeating a file: a band or scan only the preset stations...
Page 233 07 12.25 MP3/WMA player SEEK/TRACK (Seeking/Tracking ST (Stereo reception) display down) There are two scan features—you can ei- Your radio automatically changes to stereo ther scan the files in a folder on a specif- Radio reception when a stereo broadcast is re- ic disc or scan the first file of all the ceived.
Page 234 07 12.25 If this button is pushed while a compact TUNE·FILE (Tuning and File up/down) disc that does not contain text data is Radio playing, “NO TITLE” will appear on the Turn the knob clockwise to step up the display. frequency.
Page 235 07 12.25 "Type 2 CY17077y...
Page 236 ∗ ton number will appear on the display. : Use of satellite radio requires XM tuner and service. Contact your Toyota To recall a preset station: Push the button dealer for details. for the station you want. The preset but-...
Page 237 : Use of satellite radio requires XM Push the “AM·SAT” button to turn on the onds until the radio returns to the pre- tuner and service. Contact your Toyota radio and select the AM or XM band. vious channel or “CH001”. If it does dealer for details.
Page 238 (CD−DA) and MP3/WMA files, audio to the system. When the AUX adapter is data disc. data (CD−DA) is played. in use, “AUX” will appear on the display. If the malfunction still exists, take your vehicle to your Toyota dealer.
Page 239 07 12.25 LOAD PWR·VOL (Power and Volume) MP3/WMA player This button is used to load the compact Push “PWR·VOL” to turn the audio system There are two random playback features— discs in the compact disc player. This on and off. Turn “PWR·VOL” to adjust the you can either listen to all of the files on player can store up to six discs.
Page 240 07 12.25 RPT (Repeat) MP3/WMA player SCAN Compact disc player There are two repeat features—You can Radio repeat a single file or an entire folder. There are two repeat features—you can You can either scan all the frequencies on either replay a disc track or a whole com- Repeating a file: a band or scan only the preset stations pact disc.
Page 241 “ ” will appear on the dis- the player will scan the first file of the tuner and service. Contact your Toyota play and the player will scan the first next folder. To select a folder, push the dealer for details.
Page 242 ∗ : Use of satellite radio requires XM quickly. TURE) → CH NUMBER → CH NAME tuner and service. Contact your Toyota Up to 10 alphanumeric characters can be dealer for details. displayed. (Some information will not be fully displayed.)
Page 243 Turn the knob counterclockwise ∗ 1 : Use of satellite radio requires XM To change the display, quickly push and to step down the frequency. tuner and service. Contact your Toyota release “TEXT” button while ∗ Satellite Radio —...
Page 244 07 12.25 "Type 3 CY17066y...
Page 245 ∗ ton number will appear on the display. : Use of satellite radio requires XM tuner and service. Contact your Toyota To recall a preset station: Push the button dealer for details. for the station you want. The preset but-...
Page 246 : Use of satellite radio requires XM Push the “AM·SAT” button to turn on the onds until the radio returns to the pre- tuner and service. Contact your Toyota radio and select the AM or XM band. vious channel or “CH001”. If it does dealer for details.
Page 247 AUX adapter is connected If the malfunction still exists, take your entertainment system” on page 240 in this to the system. When the AUX adapter is vehicle to your Toyota dealer. Section. in use, “AUX” will appear on the display. DISC DISC·AUX (Compact disc)
Page 248 07 12.25 FOLDER (Folder up/down) To load multiple compact discs, push and RAND (Random) hold the button (until you hear a beep To skip up or down to a different folder: Compact disc player when the audio system is on), then insert Push either side of the “FOLDER”...
Page 249 07 12.25 MP3/WMA player RPT (Repeat) MP3/WMA player There are two random playback features— Compact disc player There are two repeat features—You can you can either listen to all of the files on repeat a single file or an entire folder. There are two repeat features—you can the compact discs in random order.
Page 250 To stop scanning, push this button again. push this button again. If the player has ∗ scanned all the discs, it will stop scan- : Use of satellite radio requires XM ning. tuner and service. Contact your Toyota dealer for details.
Page 251 : Use of satellite radio requires XM the player will scan the first file of the reception when a stereo broadcast is re- tuner and service. Contact your Toyota next folder. To select a folder, push the ceived. “ST” appears on the display. If the dealer for details.
Page 252 Satellite ∗ 2 Radio and “Text Information” linked to the respective audio services. ∗ 1 : Use of satellite radio requires XM tuner and service. Contact your Toyota dealer for details. ∗ 2 : Text Information includes, Channel Name, (Artist) Name, (Song) Title and...
Page 253: Audio Remote Controls
Radio ∗ : Use of satellite radio requires XM This switch has the following features— tuner and service. Contact your Toyota To select a preset station: dealer for details. Quickly push and release the “ ” or “ ” MP3/WMA player side of the switch.
Page 254: Aux Adapter
: Use of satellite radio requires XM Quickly push and release the “ ” or “ ” CY17076 tuner and service. Contact your Toyota side of the switch until the file you want dealer for details. to listen to is set. If you want to return...
Page 255: Rear Seat Entertainment System
07 12.25 Rear seat entertainment system— If you install an audio system other than a genuine audio system, you will not be able to use the AUX adapter. CY17070y...
Page 256 For details, refer to headphone. the manufacturer’s instructions. With some wireless headphone generally available in the market, it may be difficult to catch sound properly. Toyota recom- mends the use of Toyota genuine wireless headphone.
Page 257 07 12.25 —Display CY17058 CY17059 CY17060 To open the display, push the lock release Pull the display down to an easily view- To close, push the display up until you button. able angle (between 90_ and 125_) hear a click. The illumination of the screen is automati- NOTICE cally...
Page 258 07 12.25 —Rear seat entertainment system controller The rear seat entertainment system can BEFORE USING THE CONTROLLER NOTICE be operated with the rear seat entertain- (for new vehicle owners) ment system controller and buttons on the z Benzene or alkaline solutions may A battery is already set in the control- DVD player unit.
Page 259 07 12.25 Z17448 Z17449 CY17061 1. Remove the cover of the controller 2. Remove the insulating sheet. as shown.
Page 260 07 12.25 USING THE CONTROLLER NOTICE To use the rear seat entertainment sys- Observe the followings, otherwise the tem controller, direct the signal output controller may be damaged. portion of the controller to the signal reception portion of the rear seat enter- z Do not drop or strongly knock the tainment system display.
Page 261 07 12.25 —Control buttons "Controller Z18004y...
Page 262 07 12.25 1. “DVD” button 9. “ ” button 16. “ANGLE” button This button turns on the DVD mode. This button selects the angle of the This button stops a screen when the screen when the DVD player is oper- DVD player is operated.
Page 263 Install the cover. Toyota dealer. 1. Remove the cover of the controller as shown. z Dispose of used batteries according to the local laws.
Page 264 DVD player ler still does not operate properly, contact player operation screen. will be turned off simultaneously. your Toyota dealer. When the “VIDEO” button is pushed, the images and sounds from the personal au- dio machine are output.
Page 265 07 12.25 —Front audio system operation —Rear system lock The rear DVD player can be operated The audio system controls in the instru- through the front audio system. ment panel allow the operation of the rear seat entertainment system by rear seat passengers to be disabled.
Page 266: Dvd Player
The condition of the rear system lock is maintained, even when the engine switch “DVD ERROR” appears is turned off. screen: There is a problem inside the player. Eject the disc. Set the disc again. If the malfunction still exists, take your vehicle to your Toyota dealer.
Page 267 07 12.25 If a disc which is not playable is inserted, 8 cm (3 in.) compact disc singles “DISC CHECK” will also appear on the Your compact disc player needs an adap- screen. For appropriate discs for this play- tor to play compact disc singles. Compact “Audio/video system operating...
Page 268 07 12.25 —DVD player operation switches Z17485 Z17461 Z17456 EJECTING THE DISC The DVD player can be operated with the The player can also be operated with the controller buttons directly. switches on the screen. Push the “ ” button. 1.
Page 269 07 12.25 Z17462 Z18008 Z17402 Top page (DVD video operation switch) Top page (video CD) TURNING THE OPERATION SWITCHES ON AND OFF To turn on the operation switches, push the “OPTION” button on the controller. Z17401 Z18009 Second page (DVD video operation Second page (video CD)
Page 270 07 12.25 There are operation switches on the “Page 1” and “Page 2” screens. To change the screen, push the “Page 1” or “Page 2” switch on the screen. Z17404 Z18010 On the screen If “ ” appears on the screen when you select a switch, it indicates that the switch cannot work.
Page 271 07 12.25 —DVD player operation To turn off the switches on the screen, NOTE: The playback condition of some CAUTION push the “OPTION” button on the control- DVD video discs may be determined by ler once again or push the “Hide Buttons” the DVD video software producer.
Page 272 07 12.25 TURNING THE MENU SCREEN FOR THE DISC ON OR OFF To turn on the menu screen for the disc, push the “Top Menu” or the “Menu” switch on the screen. You can also turn on the menu screen by pushing the “MENU” or Z18012 “TOP MENU”...
Page 273 07 12.25 OPERATING THE “" ”, “ ”, “AA” AND “""” SWITCHES/BUTTONS “" ” switch/button: Push this switch/but- ton to pause the disc or to cancel the pause and return to normal playing. “ ” switch/button: This switch/button stops a screen when the DVD player is operated.
Page 274 07 12.25 SKIPPING PREDETERMINED SELECTING THE TITLE SCREEN To display the searching title screen, push To skip to the predetermined screen, push the “Search” switch on the screen. You the “Return” switch. The DVD player starts can also display the screen by pushing playing from the beginning of the predeter- the “SEARCH”...
Page 275 07 12.25 CHANGING THE SUBTITLE LANGUAGE Push the “Sub Title” switch on the screen, and then the changing subtitle language screen will appear. You can also display the screen by pushing the “SUB TITLE” button on the controller. Z17411 Z17413 Select the title number by using the...
Page 276 07 12.25 CHANGING AUDIO LANGUAGE Push the “Audio” switch on the screen and then the changing audio language screen will appear. You can also display the screen by pushing the “AUDIO” button on the controller. Z17414 Z17415 Each time you push the “Sub Title” switch, another language stored on the disc is selected.
Page 277 07 12.25 CHANGING ANGLE SCREEN Push the “Angle” switch on the screen, and then the changing angle screen will appear. You can also display the screen by pushing the “ANGLE” button on the controller. Z17416 Z17417 Each time you push the “Audio” switch, another language stored on the disc is selected.
Page 278 07 12.25 CHANGING THE INITIAL SETTING Push the “Set Up” switch on the screen, and then the initial setting screen will ap- pear. You can also display the screen by pushing the “SET UP” button on the con- troller. You can change the initial setting. Z17418 After the setting is done, the player plays from the beginning of the chapter or the...
Page 279 07 12.25 Z18017 Z18018 Z18019 Setup Menu screen CHANGING THE AUDIO LANGUAGE To select an audio language, use the joys- tick to enter the appropriate 4−digit lan- Push the “Audio Language” switch on the There are initial setting switches on the guage code.
Page 280 07 12.25 Z18020 Z18021 Z18022 CHANGING THE SUBTITLE LANGUAGE To enter the code of the language you CHANGING THE DVD LANGUAGE want to read, use the joystick to enter the To display “Select Subtitle Lang.” To display the “Select DVD Lang.” screen, appropriate 4−digit language code.
Page 281 07 12.25 Z18023 Z18024 Z18025 To enter the code of the language you TURNING THE ANGLE MARK ON OR SETTING LEVEL VIEWER want to read, use the joystick to enter the RESTRICTIONS appropriate 4−digit language code. For de- The angle mark can be turned on for You can restrict the play back screen by tails about the language codes, see the discs that are multi−angle compatible.
Page 282 07 12.25 SETTING THE DISPLAY MODE Pushing the “SIZE” button on the control- ler causes the display modes to change sequentially as follows: Z18026 Z18027 Normal Wide1 Wide2 Enter the password and push the “ENT” Push a parental level (1—8). The smaller button.
Page 283 07 12.25 LANGUAGE CODE LIST 0125 Aymara 0610 Fiji Code Language 0126 Azerbaijani 0615 Faroese 1001 Japanese 0201 Bashkir 0625 Frisian 0514 English 0205 Byelorussian 0701 Irish 0618 French 0207 Bulgarian 0704 Scots−Gaelic 0405 German 0208 Bihari 0712 Galician 0920 Italian 0209 Bislama...
Page 284 07 12.25 1101 Georgian 1320 Maltese 1911 Slovak 1111 Kazakh 1325 Burmese 1912 Slovenian 1112 Greenlandic 1401 Nauru 1913 Samoan 1113 Cambodian 1405 Nepali 1914 Shona 1114 Kannada 1415 Norwegian 1915 Somali 1119 Kashmiri 1503 Occitan 1917 Albanian 1121 Kurdish 1513 (Afan) Oromo 1918...
Page 285 07 12.25 USING THE CONTROL SCREEN 2019 Tsonga When playing a disc, push the “DVD” but- 2020 Tatar ton on the controller. The status screen 2023 will appear on the screen. 2111 Ukrainian Z17464 2118 Urdu 2126 Uzbek 2209 Vietnamese 2215 Volapük 2315...
Page 286 07 12.25 —DVD player operation (video CD/audio CD/CD text/MP3) Z17489 Z17433 Z18014 SELECTING THE DISC MENU NUMBER Enter the disc menu number by using the OPERATING THE “" ”, “AA” AND (video CD only) joystick and push the “ENT” button. The “""”...
Page 287 07 12.25 Z17435 Z17490 Z18006 TURNING ON THE DISC MENU (video CHANGING MENU PAGE OR TRACK CHANGING MULTIPLEX CD only) (video CD only) TRANSMISSION (video CD only) Push the “Return” switch to turn on the Push the “Next Menu” or “Prev. Menu” Push the “Main/Sub”...
Page 288 07 12.25 CHANGING THE INITIAL SETTING (video USING THE CONTROL SCREEN CD only) When playing a disc, push the “DVD” but- Push the “Set Up” switch on the screen ton on the controller. The control screen and then the initial setting screen will ap- will appear on the screen.
Page 289: Screen Adjustment
07 12.25 —Screen adjustment MP3 only— 3. “SCAN” switch You can adjust the color, contrast, tone and brightness of the screen. Folder and file names will appear on the When the “SCAN” switch is pushed, all screen when the “DVD” button is pushed. the files in a current folder will be Push the “DISPLAY”...
Page 290 07 12.25 —Selecting the video mode After adjusting the screen, push the “ENT” button or “DISPLAY” button to return to the previous screen. Z18030 Z17478 Operate the joystick up and down to se- The audio machine connected to the input lect Brightness, Contrast, Tone, or Color terminal adapter can be played in the and left and right to make adjustments.
Page 291 07 12.25 —DVD video disc information DVD PLAYER AND DVD VIDEO DISCS Marks shown on DVD video discs: DVD VIDEO DISC GLOSSARY This DVD player conforms to NTSC col- DVD video discs: Digital Versatile Disc or TV formats. DVD video discs con- that holds video.
Page 292 07 12.25 —A/V input adapter Level 8: All types of DVD video discs can Manufactured under license from Dolby The rear entertainment system plays vid- be played. Laboratories. “Dolby”, “Pro Logic”, and sound when audio−video the double−D symbol are trademarks of equipment is connected to the A/V input Multi−angle feature: You can enjoy the Dolby Laboratories.
Page 293: Power Outlet
07 12.25 —Power outlet CY17030 CY17073 CY19137 To use the adapter, open the cover. After plugging the cord into the adapter, This power outlet is designed for use as let it go through the gap between the a power supply for the audio device con- The A/V input adapter is composed of 3 console box and the tray.
Page 294 07 12.25 Other appliances requiring an extremely NOTICE stable power supply: microcomputer− controlled electric blankets, touch sen- z To prevent the battery from being sor lamps, etc. discharged, do not use the power outlet longer than necessary when Certain electrical appliances may cause the engine is not running.
Page 295: Audio/Video System Operating Hints
07 12.25 Audio/video system operating hints For example, nearby buildings and terrain Static and fluttering—These occur when NOTICE can interfere with FM reception. Power signals are blocked by buildings, trees, or lines or telephone wires can interfere with other large objects. Increasing the bass To ensure correct audio/video system AM signals.
Page 296 ∗ : Use of satellite radio requires XM the interference by one or more of interior before you use the players. tuner and service. Contact your Toyota the following measures: dealer for details. Bumpy roads or other vibrations may —Reorient or relocate the receiving make your compact disc player and antenna.
Page 297 07 12.25 DVD player only discs marked shown above. The following products may not be playable on your DVD player. Audio CDs SACD XS18016 Copy−protected CD CD−ROM DVD−R DVD+R DVD+RW DVD video DVD−RW discs DVD−ROM DVD−RAM Compact disc player Video CDs Use only compact discs marked as shown above.
Page 298 07 12.25 NOTICE z Do not use special shaped, trans- parent/translucent, low quality or la- beled discs such as those shown in the illustrations. The use of such Z17038 Z17039 discs may damage the player or changer, or it may be impossible to eject the disc.
Page 299 07 12.25 MP3/WMA FILES MP3 (MPEG Audio Layer 3) and WMA (Windows Media Audio) are audio com- pression standards. The MP3/WMA player can play MP3 Z17052 Z17053 and WMA files on CD−ROM, CD−R and CD−RW discs. The unit can play disc recordings com- patible with ISO 9660 level 1 and level Correct Wrong...
Page 300 07 12.25 WMA files can contain a WMA tag that The MP3/WMA player does not play is used in the same way as an ID3 back MP3/WMA files from discs record- tag. WMA tags carry information such er using packet write data transfer 001.mp3 as track title, artist name.
Page 301 07 12.25 The play order of the compact disc CD−R and CD−RW discs The MP3/WMA player conforms to the with the structure shown on the left is track skip function of the CD−R/CD− CD−R/CD−RW discs that have not been as follows: RW disc.
Page 302 07 12.25 TERMS ID3 Tag— Level 2: Packet write— This is a method of embedding track−re- The file name can have up to 31 charac- lated information in an MP3 file. This em- ters (including the separation mark “.” and This is a general term that describes the bedded information can include the track file extension).
Page 303 07 12.25...
Page 304 07 12.25 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Air conditioning system Controls ........... Air flow selector settings .
Page 305: Controls
07 12.25 Controls (without “DUAL” button) 1. Fan speed selector 2. “AUTO” button 3. Temperature selector 4. “A/C” button 5. Air flow selector 6. Air intake selector 7. “OFF” button CY18026...
Page 306 07 12.25 “AUTO” button Temperature selector For automatic operation of the air condi- To increase the temperature, push the “UP” side, decrease push tioning, push the “AUTO” button. An indi- “DOWN” side. cator light will illuminate to show that the automatic operation mode has been se- “LO”...
Page 307 If this happens, take your ve- Air intake selector hicle to a Toyota dealer for service. Pressing this button once again returns Push the button to select the air source. the air flow mode to the last one used.
Page 308 07 12.25 Controls (with “DUAL” button) 1. Fan speed selector 2. Temperature selector (at the independent mode: for driver) (at the linked mode: for driver and front passenger) 3. “AUTO” button 4. “DUAL” button 5. Temperature selector (for front passenger) 6.
Page 309 07 12.25 “AUTO” button Temperature selector For automatic operation of the air condi- To increase the temperature, push the “ ” side, to decrease it, push the “ ” side. tioning, push the “AUTO” button. An indi- cator light will illuminate to show that the “LO”...
Page 310 If this happens, take your ve- Air intake selector hicle to your Toyota dealer for service. Pressing this button once again returns Push the button to select the air source. the air flow mode to the last one used.
Page 311: Air Flow Selector Settings
07 12.25 Air flow selector settings Operating tips To cool off your Toyota after it has been parked in the hot sun, drive with the windows open for a few minutes. This vents the hot air, allowing the air conditioning to cool the interior more quickly.
Page 312 07 12.25 If following another vehicle on a dusty Heating Air conditioning road, or driving in windy and dusty For best results, set controls as follows: For best results, set controls as follows: conditions, it is recommended that the For automatic operation— For automatic operation—...
Page 313 07 12.25 Ventilation Defogging and defrosting Press the “A/C” button for dehumidified heating or cooling. This setting clears the For best results, set controls as follows: —The inside of the windshield front view more quickly. For automatic operation— For best results, set controls as follows: On humid days, do not blow cold air —For automatic operation Press in the “AUTO”...
Page 314: Instrument Panel And Rear Vents
07 12.25 Instrument panel and rear vents Pressing the windshield air flow button turns on the defogging function with the purpose of clearing the front view. When pressing the windshield air flow but- ton, the air intake selects FRESH auto- matically.
Page 315: Air Conditioning Filter
07 12.25 —Checking and replacing the Air conditioning filter— air conditioning filter The air conditioning filter may clog af- ter long use. The filter may need to be replaced if the air flow of the air condi- tioning and heater experiences extreme reductions in operating efficiency, or if the windows begin to fog up easily.
Page 316 07 12.25 CY72012 CY72004 CY72013 1. Open the glove box. Remove the 2. Push in each side of the glove box 3. Remove the filter case by holding screw with a Phillips−head screw- to disconnect the claws. both sides. driver and slide the hook as shown.
Page 317 07 12.25 INFORMATION The air filter should be installed prop- erly in position. The use of air condi- tioning with the air filter removed may cause deteriorated dustproof per- CY18022 formance and then affect air condi- tioning performance. 4. Remove filter from the filter...
Page 318 07 12.25 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Other equipment Multi−information display ........Compass .
Page 319: Multi−Information Display
07 12.25 Multi−information display— 1. “RESET” button 2. “MODE” button 3. Air conditioning system without “DUAL” button—Cruise information display Air conditioning system with “DUAL” button—Outside temperature and cruise information display 4. Clock 5. Air conditioning system without “DUAL” button only—Outside temperature display 6.
Page 320: Clock
If the time is between 1:30—1:59, the If “−−_C” (“−−_F”) appears on the display, time will change to 2:00. contact your Toyota dealer. The engine switch must be in the “ACC” There may be a case that “−−_C” (“−−_F”) or “ON” position.
Page 321: Cruise Information Display
2. Driving range “−−_C” (“−−_F”) will appear on the display. If “−−_C” (“−−_F”) appears on the display, 3. Average fuel consumption contact your Toyota dealer. 4. Average vehicle speed There may be a case that “−−_C” (“−−_F”) 5. Display off...
Page 322: Compass
07 12.25 Compass 2. Driving range 3. Average fuel consumption (“RANGE MI” or “RANGE km”) (“AVG. MPG” or “AVG. L/100 km”) The distance the vehicle can travel with Average fuel consumption is calculated the remaining fuel is calculated and and displayed based on total driving displayed based on the quantity of re- distance and total...
Page 323 07 12.25 The compass indicates the direction The vehicle is in a place where the that the vehicle is heading. In the earth’s magnetic field is subject to in- terference by artificial magnetic fields above case, it shows that the vehicle is heading north.
Page 324 07 12.25 CY19140 CALIBRATING THE COMPASS (deviation calibration) The direction display on the compass deviates from the true direction deter- mined by the earth’s magnetic field. The angle of deviation varies according to the geographic position of the vehicle. To adjust this deviation, stop the vehicle, then push and hold the “...
Page 325 07 12.25 After calibration, leaving the system for Samoa: 5 Guam: Saipan: several seconds returns it to the compass mode. CAUTION Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.
Page 326 07 12.25 Perform circling calibration just after you have purchased your Toyota. And then always perform circling calibration after the battery has been removed, re- placed or disconnected. Do not perform circling calibration of CY19141 CY19033 the compass in a place where the earth’s magnetic field is subject to in-...
Page 327: Rear View Monitor System
07 12.25 Rear view monitor system The rear view monitor system assists CAUTION CAUTION the driver by displaying an image of the view behind the vehicle while back- When doing the circling calibration, Never depend on rear view ing up. The image is displayed in re- be sure to secure a wide space, monitor system entirely when back- verse on the screen.
Page 328 07 12.25 When replacing the tires, please consult Do not use the system when the your Toyota dealer. If you replace the back door is not completely closed. tires, the area displayed on the screen may change. If the back of the vehicle is hit, the position and mounting angle of the camera may change.
Page 329 07 12.25 AREA DISPLAYED ON SCREEN When water droplets are adhering to the camera, or when humidity is high Image is displayed approximately level (for example, when it rains) on screen. When foreign matter (for example, The area detected by the camera is snow or mud) is adhering to the cam- limited.
Page 330: Power Outlet
07 12.25 Power outlet (12 VDC) CY19118 CY19002 CY19035 Luggage compartment If a bright light (for example, sunlight re- flected off the vehicle body) is picked up ∗ The power outlets are designed for by the camera, the smear effect peculiar power supply for car accessories.
Page 331 07 12.25 Power outlet (115 VAC) NOTICE z To prevent the fuse from being blown, do not use the electricity over the total vehicle capacity of 12 VDC/120W. CY19137 CY19135 z To prevent the battery from being discharged, do not use the power outlets longer than necessary when the engine is not running.
Page 332: Glove Box
07 12.25 Glove box Appliances with high initial peak watt- NOTICE age: cathode−ray tube type televisions, compressor−driven refrigerators, electric z To prevent the battery from being pumps, electric tools, etc. discharged, do not use the power outlet longer than necessary when Measuring devices which process pre- the engine is not running.
Page 333: Garage Door Opener
07 12.25 Garage door opener On some models, an auxiliary box is Indicator light located inside the glove box. To increase the capacity of the glove box, raise the lower panel of the auxiliary box. CY19130 Buttons CY19070 The garage door opener ( Universal Transceiver) is manufactured under license from HomeLink and can...
Page 334 07 12.25 (a) Programming the HomeLink The HomeLink in your vehicle has 3 HomeLinkr buttons and you can store one program for each button. To ensure correct programming into the CY19131 CY19132 HomeLink , install a new battery in the hand−held transmitter prior to program- 25 to 75 mm ming.
Page 335 07 12.25 6. Repeat steps 2 through 5 for each re- The ceiling mounted garage door opener maining HomeLink button to program motor should recognize another device. HomeLink unit and be able activate the garage door up/down. Programming a rolling code system 4.
Page 336 Programming other devices Refer to HomeLink on the internet at: To program other devices such as home WWW.HOMELINK.COM security systems, home door locks or lighting, contact your authorized Toyota dealer for assistance. Reprogramming a button (c) Erasing entire HomeLink Individual HomeLink...
Page 337: Auxiliary Boxes
07 12.25 Auxiliary boxes— To use the auxiliary boxes, open the CAUTION This device complies with Part 15 of the lids as shown in the following illustra- FCC Rules and with RSS−210 of the IC tions. When programming the HomeLink Rules.
Page 338 07 12.25 CY19005 CY19036 CY19069 Type A (overhead console) Type C (rear console box) Type E (right side of luggage compart- ment) CY19007 CY19112 Type B (instrument panel) Type D (rear tire house)
Page 339: Rear Console Box
07 12.25 —Using the holding belts Rear console box CONSOLE BOX TABLE To use the console box table, open it. CAUTION CY19074 To reduce the chance of injury in case of an accident or a sudden stop, always keep the table closed while driving.
Page 340: Tissue Box Holder
07 12.25 Tissue box holder The rear console box is equipped with a tissue box holder on the inside of the rear console box lid. To use the tissue box holder: 1. Pull up the console box lid while push- CY19104 ing the lock release button.
Page 341: Coin Holder
07 12.25 Coin holder Trash holder The rear console box is equipped with a coin holder. To use the coin holder: 1. Pull up the console box lid while push- ing the lock release button. 2. Push coins down into the holder. The coin holder is detachable.
Page 342: Front Cup Holders
07 12.25 Front cup holders The trash holder is designed to use the grocery bag as a trash bag. To use the trash holder: 1. Raise the trash holder. 2. Fit the grocery bag onto the holder by CY19064 hanging its handles on the two hooks indicated at the left and right.
Page 343: Rear Cup Holders And Tray
07 12.25 Rear cup holders and tray (vehicles without third seats) The cup holders are designed for hold- ing cups or drink−cans securely. The cup holder can be adjustable to the size of the cups or drink−cans by changing the holder position and the arm position, as shown.
Page 344 07 12.25 2. To use the rear cup holder, push and 3. To use the tray, pull it out. pull it out. CAUTION Do not place anything else other than cups or drink−cans in the cup holder, such items thrown about in the compartment and possibly injure people in the vehicle during sudden braking or in an accident.
Page 345: Rear Cup Holders
07 12.25 Rear cup holders (vehicles with third seats) Bottle holders The cup holders are designed for hold- ing cups or drink−cans securely. Type A—To use the holder, pull the arm- rest out and push the lid. CY19114 CAUTION CY19015 Do not place anything else other than cups or drink−cans in the cup holder,...
Page 346: Tie−Down Hooks
07 12.25 Tie−down hooks Grocery bag hooks The bottle holders are designed to hold bottles securely. CAUTION Do not attempt to use the holder for CY19044 CY19076 any other purpose for which it was intended. Inappropriately sized shaped objects may be thrown about in the compartment and possibly in- jure people in the vehicle during a sudden braking or an accident.
Page 347: Cargo Net Hooks
07 12.25 Cargo net hooks Luggage cover USING LUGGAGE COVER To use the luggage cover: 1. Attach the front hooks of the lug- gage cover to the head restraint. 2. Pull out the rear luggage cover and CY19045 hook it on the anchors. CAUTION Do not place anything on the luggage cover.
Page 348: Double Deck
07 12.25 Double deck CY19067 CY19058 CY19068 REMOVING LUGGAGE COVER To use the double deck: 2. Hold the handle and raise the double deck on the rear tire houses. To remove the luggage cover, detach its 1. Turn the left and right knobs from hooks from the head restraint.
Page 349: Roof Luggage Carrier
07 12.25 Roof luggage carrier NOTICE When using the double deck at the raised position, do not place any ob- ject heavier than 30 kg (66 lb.). CY19052 CY19129 3. Turn the left and right knobs from “UNLOCK” position “LOCK” position. Make sure the double deck is securely locked.
Page 350 When there is no luggage on the roof luggage carrier, Toyota recommends that Loading cargo on the roof luggage the front and rear cross rails be secured carrier will make the center of the in the positions indicated in the illustra- vehicle gravity higher.
Page 351: Floor Mat
07 12.25 Floor mat CY19047 CY19048 Use a floor mat of the correct size. CAUTION If the vehicle carpet and floor mat have 2 holes, then they are designed for use Observe the following precautions. with locking clips. Attach the floor mat to Failure to do so may result in the the vehicle carpet using the clips.
Page 352 ........Your Toyota’s identification .
Page 353: Off−Road Vehicle Precautions
07 12.25 Off−road vehicle precautions This vehicle belongs to the utility ve- CAUTION hicle class, which has higher ground clearance and narrower tread in relation Always observe the following precau- to the height of its center of gravity to tions to minimize the risk of serious make it capable of performing in a wide personal injury or damage to your ve- variety of off−road applications.
Page 354: Break−In Period
Toyota has a smaller fuel tank opening. winds than an ordinary passenger your vehicle: The special nozzle on pumps with un- car. Slowing down will allow you to...
Page 355 Rating lower than 87 may result in engine Automotive manufacturers in the U.S., Toyota, be sure that it has an octane knocking. Persistent knocking can lead to Europe and Japan have developed a rating no lower than 87.
Page 356: Fuel Pump Shut Off System
07 12.25 Fuel pump shut off system Operation in foreign countries The fuel pump shut off system stops sup- If you plan to drive your Toyota in NOTICE plying fuel to the engine to minimize the another country... risk of fuel leakage when the engine stalls...
Page 357: Three−Way Catalytic Converters
Do not drive with an extremely low vehicle in for a check−up as soon fuel level; running out of fuel could as possible. Remember, your Toyota cause the engine to misfire, creat- dealer knows your vehicle and its ing an excessive load on the three−...
Page 358: Engine Exhaust Cautions
To allow proper operation of your Toyota dealer. Failure to do so may accident or fire due to engine over- vehicle’s ventilation system, keep allow exhaust gases to enter the heating. Additionally, if the vehicle...
Page 359: Facts About Engine Oil Consumption
It is normal that an engine should con- regularly. Toyota recommends that the oil A new engine consumes more oil, since sume some engine oil during normal level be checked every time you refuel its pistons, piston rings and cylinder walls engine operation.
Page 360: Iridium−Tipped Spark Plugs
If the brake system increase. warning light comes on, immediately stop your vehicle and contact your Toyota deal- It is not a malfunction that the brake sys- tem warning light may stay on for 60 sec- onds after the engine switch is turned to the “ON”...
Page 361 07 12.25 ANTI−LOCK BRAKE SYSTEM Depressing the brake pedal on slippery CAUTION (with “ABS” warning light) road surfaces such as on a manhole cov- er, a steel plate at a construction site, The anti−lock brake system is designed overestimate anti−lock joints in a bridge, etc.
Page 362 07 12.25 “ABS” warning light Driving with tire chains installed. The light comes on when the engine Driving over the steps such as the switch is turned to the “ON” position. If joints on the road. the anti−lock brake system and the brake assist system work properly, the light...
Page 363 07 12.25 When the “ABS” warning light is on (and Have your Toyota dealer perform the bed- CAUTION the brake system warning light is off), the ding−down. anti−lock brake system does not operate BRAKE ASSIST SYSTEM If the “ABS” warning light remains on...
Page 364: Brake Pad Wear Limit Indicators
This is the primary identification number checked and replaced by your Toyota for your Toyota. It is used in registering Use only a spare tire of the same dealer as soon as possible. Expensive ro- the ownership of your vehicle.
Page 365: Identification Number
07 12.25 —Engine number The engine number is stamped on the engine block as shown. CY20023 CY20014 4.0 L V6 (1GR−FE) engine The vehicle identification number (VIN) is also on the Certification Label. CY20005 4.7 L V8 (2UZ−FE) engine...
Page 366: Theft Prevention Labels
07 12.25 Theft prevention labels (except for Canada) Suspension and chassis Your new vehicle carries theft preven- CAUTION tion labels which are approximately 47 mm (1.85 in.) by 12 mm (0.47 in.). Do not modify the suspension/chassis The purpose of these labels is to reduce with lift kits, spacers, springs, etc.
Page 367: Tire Information
07 12.25 Tire information— —Tire symbols This illustration indicates typical tire symbols. 1. Tire size—For details, see “—Tire size” on page 354. 2. DOT and Tire Identification Number (TIN)—For details, see “—DOT and Tire Identification Number (TIN)” on page 353. 3.
Page 368: Tire
07 12.25 —DOT and Tire Identification Number (TIN) 7. “TUBELESS” “TUBE The “DOT” symbol certifies that the TYPE”—A tubeless tire does not tire conforms to applicable Federal have a tube inside the tire and air Motor Vehicle Safety Standards. is directly filled in the tire. A tube type tire has a tube inside the tire and the tube maintains the air CY20027...
Page 369 07 12.25 —Tire size —Name of each section of tire CY20029 Z20007 Z20008 This illustration indicates typical tire 1. Section width 1. Bead size. 2. Tire height 2. Sidewall 1. Tire (P=Passenger car, 3. Wheel diameter 3. Shoulder T=Temporary use) 4.
Page 370: Uniform Tire Quality Grading
150 would wear conditions on specified government purchasers of Toyota vehicles with in- one and a half (1−1/2) times as well test surfaces of asphalt and concrete. formation on uniform tire quality grad-...
Page 371 07 12.25 Temperature A, B, C—The tempera- ture grades are A (the highest), B, and C, representing the tire’s resis- tance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 372: Glossary
07 12.25 —Glossary of tire terminology Tire related term Meaning tire inflation pressure when the vehicle has been parked for at least 3 hours Cold tire inflation pressure or more, or it has not been driven more than 1.5 km or 1 mile under that condition the maximum cold inflation pressure to which a tire may be inflated and it is Maximum inflation pressure...
Page 373 07 12.25 Tire related term Meaning distribution of occupants in a vehicle as specified in the third column of Table Occupant distribution 1 that follows the combined weight of those installed regular production options weighing over 2.3 kg (5 lb.) in excess of those standard items which they replace, not pre- Production options weight viously considered in curb weight or accessory weight, including heavy duty brakes, ride levelers, roof rack, heavy duty battery, and special trim...
Page 374 07 12.25 Tire related term Meaning Weather side the surface area of the rim not covered by the inflated tire the part of the tire that is made of steel wires, wrapped or reinforced by ply Bead cords and that is shaped to fit the rim Bead separation a breakdown of the bond between components in the bead a pneumatic tire in which the ply cords that extend to the beads are laid at...
Page 375 07 12.25 Tire related term Meaning Groove the space between two adjacent tread ribs the layer(s) forming the inside surface of a tubeless tire that contains the inflat- Innerliner ing medium within the tire Innerliner separation the parting of the innerliner from cord material in the carcass (A) the sidewall that contains a whitewall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or...
Page 376 07 12.25 Tire related term Meaning Outer diameter the overall diameter of an inflated new tire the linear distance between the exteriors of the sidewalls of an inflated tire, Overall width including elevations due to labeling, decorations, or protective bands or ribs a tire intended for use on passenger cars, multipurpose passenger vehicles, Passenger car tire and trucks, that have a gross vehicle weight rating (GVWR) of 10,000 lb.
Page 377 07 12.25 Tire related term Meaning a tire that attains a traction index equal to or greater than 110, compared to the ASTM E−1136 Standard Reference Test Tire, when using the snow traction Snow tire test as described in ASTM F−1805−00, Standard Test Method for Single Wheel Driving Traction in a Straight Line on Snow−and Ice−Covered Surfaces, and which is marked with an Alpine Symbol ( ) on at least one sidewall...
Page 378 07 12.25 Table 1– Occupant loading and distribution for vehicle normal load for various designated seating capacities Designated seating capacity, number Vehicle normal load, number of occu- Occupant distribution in a normally of occupants pants loaded vehicle 2 through 4 2 in front 5 through 10 2 in front, 1 in second seat...
Page 379: Vehicle Load Limits
07 12.25 Vehicle load limits Vehicle load limits include total load Seating capacity: Towing capacity: capacity, seating capacity, towing ca- Without third seats: For weight carrying hitch pacity and cargo capacity. Follow the Total 5 (Front 2, Rear 3) 2268 kg (5000 lb.) load limits shown below.
Page 380: Cargo And Luggage
07 12.25 Cargo and luggage— —Stowage precautions Cargo capacity When stowing cargo and luggage in D Do not store more than 91 kg the vehicle, observe the following: Cargo capacity may increase or de- (200 lb.) of cargo and luggage crease depending on the size (weight) D Put cargo and luggage in the lug- in the luggage compartment.
Page 381: Capacity And Distribution
07 12.25 —Capacity and distribution Cargo capacity depends on the to- (4) The resulting figure equals the D Do not place anything on the tal weight of the occupants. available amount of cargo and luggage cover. Such items may luggage load capacity. For exam- (Cargo capacity) = (Total load capac- be thrown about and possibly ple, if the “XXX”...
Page 382 07 12.25 From this condition, if 3 more passen- CAUTION gers with the combined weight of 176 kg (388 lb.) get on, the available car- Even if the total load of occu- go and luggage load will be reduced pant’s weight and the cargo load as follows: is less than the total load capac- Z20004...
Page 383: Types Of Tires
07 12.25 Types of tires Determine what kind of tires your All season tires, however, do not have Weight of the vehicle is originally equipped with. adequate traction performance Cargo removed third compared with snow tires in heavy or capacity 1.
Page 384 07 12.25 SECTION STARTING AND DRIVING Before starting the engine ........How to start the engine .
Page 385: Before Starting The Engine
07 12.25 How to start the engine— Before starting the engine —Cranking hold function (a) Before cranking 1. Check the area around the vehicle be- Once turn engine switch 1. Apply the parking brake firmly. fore entering it. “START” position and release it, the crank- 2.
Page 386: Tips For Driving In Various Conditions
To dry them, drive vehicle cautiously while lightly pressing the brake pedal with the park- ing brake applied. If they still do not work safely, pull to the side of the road and call a Toyota dealer for assistance.
Page 387 07 12.25 Vehicles with rear height control air Do not drive in excess of the speed Vehicles with rear height control air suspension: When drive limit. Even if the legal speed limit suspension: If you drive through bumpy road, it is recommended that permits it, do not drive over 140 deep water over about 700 mm (28 the vehicle height should be set in the...
Page 388: Driving In The Rain
After driving through puddle, flooded, be sure to have your Toyota ating properly. lightly depress the brake pedal to dealer check brake function, changes make sure that the brakes are func- in quantity and quality of oil and fluid tioning properly.
Page 389: Off−Road Driving Precautions
07 12.25 Off−road driving precautions When driving your vehicle off−road, please Recreational Vehicle Clubs After driving through tall grass, observe the following precautions to en- U.S. Forest Service and Bureau of mud, rock, sand, rivers, etc., check sure your driving enjoyment and to help Land Management that there is no grass, bush, paper, prevent the closure of areas to off−road...
Page 390: Winter Driving Tips
NOTICE z Sand and mud that has accumulated tected against freezing. in brake drums and around brake z If driving through water, such as Only use “Toyota Super Long Life Coolant” discs may affect braking efficiency when crossing shallow streams,...
Page 391: Dinghy Towing
Section 7−3 tells you how to visually in- CY30020 spect the battery. Your Toyota dealer and Do not use your parking brake when most service stations will be pleased to there is a possibility it could freeze.
Page 392: Trailer Towing
Ask your ing supply company, trucking company, local Toyota dealer for further details be- junk yard, etc. fore towing. CAUTION...
Page 393 07 12.25 CAUTION If towing a trailer and cargo weigh- ing over 2268 kg (5000 lb.), Toyota The maximum gross trailer weight recommends to use a weight dis- (trailer weight plus cargo weight) tributing hitch. must never exceed the following for...
Page 394 07 12.25 The gross vehicle weight must not Also for weight distributing hitch Total trailer weight Tongue load exceed the Gross Vehicle Weight (4.7 L V8 [2UZ−FE] engine only) Rating (GVWR) indicated Two−wheel drive models Certification Label. The gross vehi- 331 kg (730 lb.) cle weight is the sum of weights of Four−wheel drive models...
Page 395 07 12.25 HITCHES CAUTION If you wish to install a trailer hitch, you should consult with your Toyota dealer. Do not tow the vehicle using the Use only a hitch recommended by the hooked portion of the weight carrying hitch manufacturer and the one which hitch.
Page 396 2 threads. The trailer ball shank must be matched to the ball mount hole diameter size. NOTICE Only use a ball mount attachment 1 Coupler specified for the Toyota 4runner. 2 Trailer ball 3 Ball mount attachment...
Page 397 Be sure to position the towing brake con- troller where it does not prevent the driver from operating the pedal. Toyota recommends that the sub wire har- ness be stored in the glove box when it is not in use.
Page 398 BREAK−IN SCHEDULE CONTROL OFF” switch to turn off the rear height control air suspension. Toyota recommends that you do not tow a trailer with a new vehicle or a 2. Connect a trailer. vehicle with any new power train com- 3.
Page 399 07 12.25 DISCONNECTING A TRAILER (models 7. Move the vehicle forward in the “LO” TRAILER TOWING TIPS with rear height control air suspension) (low) mode where the hitch does not When towing a trailer, your vehicle will touch anything in the “N”...
Page 400 07 12.25 Because stopping distance may be in- Crosswinds and rough roads will ad- Because of the added load of the trail- creased, vehicle−to−vehicle distance versely affect handling of your vehicle er, your vehicle’s engine may overheat should be increased when towing a and trailer, causing sway.
Page 401: How To Save Fuel And Make Your Vehicle Last Longer
07 12.25 How to save fuel and make your vehicle last longer When restarting out after parking on a Improving fuel economy is easy—just take Slow down and downshift before slope: it easy. It will help make your vehicle last descending steep or long downhill longer, too.
Page 402 07 12.25 Avoid long engine idling. If you have Keep front wheels in proper CAUTION a long wait and you are not in traffic, alignment. Avoid hitting the curb and it is better to turn off the engine and slow down on rough roads. Improper Never turn off the engine to coast start again later.
Page 403 07 12.25...
Page 404 07 12.25 SECTION IN CASE OF AN EMERGENCY If your vehicle will not start ........If your engine stalls while driving .
Page 405: If Your Vehicle Will Not Start
Have converter may overheat and become a this position for about 30 seconds. Then the key checked at your Toyota dealer. If fire hazard. the cranking hold function stops cranking none of your keys work, there may be a automatically, and you can try starting the malfunction in the immobilizer system.
Page 406: Jump Starting
07 12.25 (c) Jump starting To avoid serious personal injury and JUMP STARTING PROCEDURE The gas normally produced by a damage to your vehicle which might re- 1. If the booster battery is installed in battery will explode if a flame or sult from battery explosion, acid burns, another vehicle, make sure the vehicles spark is brought near.
Page 407 07 12.25 Jumper cable Discharged battery Booster CY40009 CY40010 CY40045 battery Positive Negative terminal terminal (“+” mark) Discharged battery Positive terminal (“−” mark) Jumper cable (“+” mark) Booster battery Connecting point for 4.0 L V6 (1GR−FE) 4. Make the cable connections in the or- c.
Page 408: If Your Engine Stalls While Driving
Move cautiously off the not apparent (for example, lights left on), road to a safe place. CAUTION you should have it checked at your Toyota 2. Turn on your emergency flashers. dealer. 3. Turn the engine switch to “ACC” or...
Page 409: If You Cannot Increase Engine Speed
When the engine is running, keep checked by your Toyota dealer as soon as flashers. Put the transmission in “P” hands and clothing away from the possible. and apply the parking brake. Turn off moving fan and engine drive belts.
Page 410: If You Have A Flat Tire
You should have it checked as by the jack. soon as possible at your Toyota dealer. 5. Read the following instructions D Stop the vehicle on a level firm thoroughly.
Page 411: Location
07 12.25 —Required tools and spare tire NOTICE D Make sure to set the jack prop- erly in the jack point. Raising z Do not continue driving with the vehicle with jack improper- a deflated tire. Driving even a ly positioned will damage the short distance can damage a vehicle or may allow the ve- CY40055...
Page 412 07 12.25 CY40056 CY40050 CY40052 Turn the jack joint by hand. To remove the spare tire under the When connecting the jack handle ex- luggage compartment: tensions, use the jack handle to tight- To remove: Turn the joint in direction en the square head bolt.
Page 413: Removing Wheel Ornament
07 12.25 —Blocking the wheel —Removing wheel ornament CY40047 CY40011 CY40020 2. Insert the end of the jack handle 2. Block the wheel diagonally op- 3. Remove the wheel ornament. extension into the lowering screw posite the flat tire to keep the Pry off the wheel ornament, using the and turn it counterclockwise with vehicle from rolling when it is...
Page 414: Jack Point
07 12.25 —Loosening wheel nuts —Positioning the jack CAUTION Never use oil or grease on the bolts or nuts. The nuts may loose and the wheels may fall off, CY40021 CY40059 which could cause a serious ac- cident. Rear Front 4.
Page 415 07 12.25 —Raising your vehicle CY40051 CY40052 CY40054 Front of vehicle Put a jack handle, jack handle exten- When connecting the jack handle ex- 6. After making sure that no one sions and jack handle end together tension(s) and jack handle end, use is in the vehicle, as the jack as shown in the illustration.
Page 416 07 12.25 —Changing wheels CAUTION Never get under the vehicle when the vehicle is supported by the jack alone. CY40058 CY40022 7. Raise the vehicle high enough 8. Remove the wheel nuts and so that the spare tire can be change tires.
Page 417: Wheel Nuts
07 12.25 —Reinstalling wheel nuts CAUTION Never use oil or grease on the bolts or nuts. Doing so may lead to overtightening the nuts and CY40023 CY40024 damaging the bolts. The nuts may loose and the wheels may fall off, which could cause a seri- ous accident.
Page 418: Reinstalling Wheel Ornament
07 12.25 —Lowering your vehicle —Reinstalling wheel ornament CAUTION D When lowering the vehicle, make sure all portions of your body and all other persons CY40025 CY40026 around will not be injured as the vehicle is lowered to the ground. D Have the wheel nuts tightened with torque wrench to 110 N·m (11.5 kgf·m, 83 ft·lbf), as soon...
Page 419: Specifications
07 12.25 —After changing wheels 12.Check the air pressure of the re- CAUTION CAUTION placed tire. Adjust the air pressure to the specifi- D Take due care in handling the Before driving, make sure all the cation designated on page 467 in ornament to avoid unexpected tools, jack and flat tire are se- Section 8.
Page 420: If Your Vehicle Becomes Stuck
07 12.25 If your vehicle needs to be If your vehicle becomes stuck towed— If your vehicle becomes stuck in snow, NOTICE (a) Towing with wheel lift type truck— mud, sand, etc., then you may attempt to rock the vehicle free by moving it If you rock your vehicle, observe the forward and backward.
Page 421 If towing is necessary, we recommend TOWING PRECAUTIONS: (a) Towing with wheel lift type truck— you to have it done by your Toyota Use a safety chain system for all towing, dealer or a commercial tow truck ser- and abide by the state/provincial and local vice.
Page 422 07 12.25 Two−wheel drive models— Four−wheel drive models— NOTICE (a) Towing with wheel lift type truck (a) Towing with wheel lift type truck z When lifting wheels, take care to From front—Use a towing dolly under the FULL−TIME FOUR WHEEL DRIVE ensure adequate ground clearance rear wheels.
Page 423: Emergency Towing
Towing in this manner may be done only All models— If towing is necessary, we recommend on hard−surfaced roads for a short dis- you to have it done by your Toyota tance speeds. Also, (c) Towing with sling type truck...
Page 424: Emergency Towing Eyelet Precautions
If the towing vehicle can hardly time four−wheel drive models, unlock the move, do not forcibly continue the center differential. towing. Contact your Toyota dealer or a commercial tow truck service CAUTION for assistance. Tow the vehicle as straight ahead If the engine is not running, the pow- as possible.
Page 425: If You Cannot Shift Automatic Transmission Selector Lever
6. Start the engine. For your safety, 2. Pry up the cover with a flathead keep the brake pedal depressed. screwdriver or equivalent. Be sure to have the system checked by your Toyota dealer as soon as possible.
Page 426: If You Lose Your Keys
Even if you lose only one key, contact Have the registered identification numbers your Toyota dealer to make a new key. If of your transmitters deleted from your ve- you lose all your master keys, you cannot hicle by your Toyota dealer as soon as make new keys;...
Page 427 07 12.25...
Page 428 CORROSION PREVENTION AND APPEARANCE CARE Protecting your Toyota from corrosion ......Washing and waxing your Toyota .
Page 429: Protecting Your Toyota From Corrosion
Now, it is up to be dry. to see all the mud and dirt. It will do you. Proper care of your Toyota can help more harm than good to simply wet the High ambient temperatures can cause ensure long−term corrosion prevention.
Page 430: Washing And Waxing Your Toyota
07 12.25 Washing and waxing your Toyota Check the interior of your vehicle. Wa- Washing your Toyota Exhaust gases cause the exhaust ter and dirt can accumulate under the Keep your vehicle clean by regular pipe to become quite hot. When floor mats and could cause corrosion.
Page 431 07 12.25 Plastic wheel ornaments: plastic Exterior lights: Wash carefully. Do not use Automatic car wash wheel ornaments are damaged easily by organic substances or scrub them with a Your vehicle may be washed in an auto- organic substances. If any organic sub- hard brush.
Page 432: Cleaning The Interior
07 12.25 Cleaning the interior Waxing your Toyota Vinyl interior CAUTION Polishing and waxing is recommended The vinyl upholstery may be easily to maintain the original beauty of your cleaned with a mild soap or detergent Be careful not to splash water or Toyota’s finish.
Page 433 07 12.25 Carpets NOTICE NOTICE Use a good foam−type shampoo to z Do not use dye or bleach on the z Do not use organic substances (sol- clean the carpets. belts—it may weaken them. vents, kerosene, alcohol, gasoline, Begin by vacuuming thoroughly to remove etc.) or alkaline or acidic solutions.
Page 434: Rain Clearing Mirrors
If you have any questions about the z Never use organic substances such light. cleaning of your Toyota, your local as benzine, alcohol or gasoline, or Toyota dealer will be pleased to answer alkaline or acid solutions for clean- them. leather these could cause discoloring.
Page 435 07 12.25 The restoring time depends on the dirt z Do not use any water repellents as quantity and dirt types. If the mirror is they can destroy the rain clearing exposed to the sunlight 1 or 2 days, the effect.
Page 436 07 12.25 SECTION VEHICLE MAINTENANCE AND CARE Maintenance requirements ........General maintenance .
Page 437: Maintenance Requirements
See form them are presented on page 427 in or if you prefer, your Toyota dealer will be “Owner’s Warranty Information Booklet” Section 7. pleased to do them at a nominal cost.
Page 438: General Maintenance
Information Booklet” or “Owner’s Manual should investigate the cause or take your information. Supplement” for the details. vehicle to your Toyota dealer or a quali- Radiator, condenser and hoses fied service shop immediately. It is recom- mended that any problem you notice be...
Page 439 07 12.25 Power steering fluid level Seats Brakes Check the level through the reservoir. The Check that all front seat controls such as In a safe place, check that the brakes do level should be in the “HOT” or “COLD” seat adjusters, seatback recliner, etc.
Page 440: Does Your Vehicle Need Repairing
Be on the alert for changes in perfor- If you notice any of these clues, take your mance, sounds, and visual tip−offs that vehicle to your Toyota dealer as soon as Check that all doors including back door indicate service is needed. Some impor- possible.
Page 441: Emissions Inspection And Maintenance (I/M) Programs
Toyota dealer comes on. In this case, your vehicle may to prepare the vehicle for re−testing. not pass the I/M test and need to be repaired.
Page 442 07 12.25 SECTION − DO−IT−YOURSELF MAINTENANCE Introduction Engine compartment overview ....... Fuse locations .
Page 443: Engine Compartment
07 12.25 Engine compartment overview "4.0 L V6 (1GR−FE) engine 1. Windshield and back window washer fluid tank 2. Power steering fluid reservoir 3. Engine oil level dipstick 4. Engine coolant reservoir 5. Engine oil filler cap 6. Brake fluid reservoir 7.
Page 444 07 12.25 "4.7 L V8 (2UZ−FE) engine 1. Windshield and back window washer fluid tank 2. Power steering fluid reservoir 3. Engine coolant reservoir 4. Engine oil level dipstick 5. Engine oil filler cap 6. Brake fluid reservoir 7. Fuse block 8.
Page 445: Service Precautions
Read separate Toyota Warranty statement for details and suggestions. This Section gives instructions only for those items that are relatively easy for an CY71030 owner to perform. As explained in Section...
Page 446 (Removing rings, harmful contaminants which z Add only “Toyota Super Long Life watches, and ties is advisable.) cause skin disorders such as in- Coolant” or similar high quality eth- Right after driving, engine flammation or skin cancer, so care...
Page 447: Parts And Tools
Funnel (only for adding coolant) fied type. Using other types will nance. Remember all Toyota parts are de- cause engine damage, loss of per- CHECKING BRAKE FLUID signed in metric sizes, so your tools must formance or radio noise.
Page 448 07 12.25 CHECKING AND REPLACING FUSES Parts (if replacement is necessary): Fuse with same amperage rating as original ADDING WASHER FLUID Parts: Water Washer fluid containing antifreeze (for winter use) Tools: Funnel REPLACING LIGHT BULBS Parts: Bulb with same number and wattage rating original (See...
Page 449 07 12.25...
Page 450 07 12.25 SECTION − DO−IT−YOURSELF MAINTENANCE Engine and Chassis Checking the engine oil level ....... . . Checking the engine coolant level .
Page 451: Checking The Engine Oil Level
07 12.25 Checking the engine oil level With the engine at operating tempera- If the oil level is below or only slightly ture and turned off, check the oil level above the low level, add engine oil of Low level Full level on the dipstick.
Page 452 ENGINE OIL SELECTION If SAE 5W−30 oil is not available, SAE 10W−30 oil may be used. However, it “Toyota Genuine Motor Oil” is used in should be replaced with SAE 5W−30 at your Toyota vehicle. Use Toyota approved the next oil change.
Page 453: Checking The Engine Coolant Level
−35_C mance for your engine, “Toyota Genuine cock and water pump. (−31_F). Motor Oil” is available, which has been If you can find no leak, have your Toyota specifically tested and approved for all Canada—“Toyota Super Long Life Toyota engines.
Page 454: Checking The Radiator And Condenser
Checking brake fluid If any of the above parts are extremely dirty or you are not sure of their condi- tion, take your vehicle to a Toyota dealer. CAUTION CY72025 To prevent burning yourself, be care- ful not to touch the radiator or con- denser when the engine is hot.
Page 455: Checking Power Steering Fluid
07 12.25 Checking power steering fluid Refilling brake fluid: NOTICE 1. Turn the engine switch off. If cold O.K. If you spill some of the fluid, be sure If hot O.K. 2. Depress the brake pedal more than 20 to wipe it off to prevent it from dam- Close times (until the brake pedal resistance aging the parts or paintwork.
Page 456: Checking Tire Inflation Pressure
07 12.25 Checking tire inflation pressure Clean all dirt from the outside of the res- Keep your tire inflation pressures ervoir tank and look at the fluid level. If at the proper level. the fluid is cold, the level should be in the The recommended cold tire inflation “COLD”...
Page 457 If a gauge and air pump are not avail- pressure molded on the tire side- able, have your vehicle checked by wall. your Toyota dealer. D Always use a tire pressure gauge. The appearance of a tire CAUTION can be misleading. Besides, tire...
Page 458: Checking And Replacing Tires
D A greater possibility of tire damage from road hazards If a tire frequently needs refilling, CY72126 have it checked by your Toyota deal- High tire pressure (overinfla- tion)— D Poor handling CAUTION D Excessive wear D Uneven wear Keep your tires properly inflated.
Page 459 07 12.25 The tires on your Toyota have built−in If air loss occurs while driving, do not REPLACING YOUR TIRES treadwear indicators to help you know continue driving. Driving even a short When replacing a tire, use a tire of when the tires need replacement.
Page 460: Rotating Tires
Otherwise, an accident may occur resulting in death or serious injuries. Toyota recommends all four tires, or at least both of the front or rear D Do not mix radial, bias belted, tires be replaced at a time as a set.
Page 461: Installing Snow Tires And Chains
07 12.25 Installing snow tires and chains See “If you have a flat tire” on page WHEN SNOW TIRES Four−wheel drive models: CHAINS 395 in Section 4 for tire change proce- Do not use snow tires of different dure. Snow tires or chains are recommended brands, sizes, construction or tread when driving on snow or ice.
Page 462: Replacing Wheels
Consult your CHAIN INSTALLATION avoid losing control of the vehicle. Toyota dealer about how to set up the tire Otherwise an accident may occur. Install the chains on the rear tires as pressure warning valves and transmitters.
Page 463: Aluminum Wheel Precautions
When balancing your wheels, use only at your Toyota dealer. Do not use wheels other than the Toyota balance weights or equivalent A wheel of a different size or type may and a plastic or rubber hammer. manufacturer’s recommended size,...
Page 464 07 12.25 SECTION − DO−IT−YOURSELF MAINTENANCE Electrical components Checking battery condition ........Battery recharging precautions .
Page 465: Checking Battery Condition
07 12.25 Checking battery condition— —Precautions —Checking battery exterior Terminals CAUTION If electrolyte gets on your skin, thoroughly wash the contact area. If BATTERY PRECAUTIONS you feel pain or burning, get medi- cal attention immediately. The battery produces flammable and explosive hydrogen gas.
Page 466: Battery Recharging Precautions
White and moon roof. To normalize them, see checked by your NOTICE “Power windows” on page 27, “Power back Toyota dealer. window” on page 30, “Back door” on page Never recharge the battery while the Clear or Have battery 32 and “Electric moon roof” on page 39 engine is running.
Page 467: Checking And Replacing Fuses
07 12.25 Checking and replacing fuses Type A fuses can be pulled out by using the pull−out tool. The location of the pull− Type A out tool is shown in the illustration. If you are not sure whether the fuse has blown, try replacing the suspected fuse with one that you know is good.
Page 468: Adding Washer Fluid
You may use plain water as washer fluid. there is a problem with the electrical sys- However, in cold areas where tempera- tem. Have your Toyota dealer correct it as tures range below the freezing point, use soon as possible.
Page 469: Replacing Light Bulbs
However, if the LEDs burn out, take your vehicle to there is a large drop of water on the your Toyota dealer to have the light re- inside of the lens, or if there is water placed.
Page 470 07 12.25 A: HB3 halogen bulbs Light bulbs Bulb No. Type B: H11 halogen bulbs Headlights (high beam) 9005 C: HB4 halogen bulbs D: Wedge base bulbs (amber) Headlights (low beam) — E: Single end bulbs Front fog lights 9006 F: Wedge base bulbs (clear) Parking and front side marker lights G: Double end bulbs...
Page 471: Headlight
If the connector is tight, wiggle it. vehicle. Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer.
Page 472: Front Fog Light
07 12.25 —Front fog lights CY73041 CY73009 CY73042 1. Turn the bulb base counterclockwise 2. Unplug the connector while depress- 3. Install a new bulb and connector to the front of the vehicle as shown. ing the lock release. into the mounting hole and turn them clockwise to the front of the If the connector is tight, wiggle it.
Page 473: Back−Up Light
07 12.25 —Parking and front side —Rear turn signal and marker lights —Front turn signal lights back−up lights CY73043 CY73045 CY73047 flathead screwdriver which wrapped with a cloth. CY73044 CY73046 CY73048...
Page 474: High Mounted Stoplight
07 12.25 —License plate lights —High mounted stoplight Clips CY73049 CY73028 CY73030 a: Rear turn signal light Use a Phillips−head screwdriver. Disconnect the clips by using a flathead b: Back−up light screwdriver which wrapped with a cloth. CY73029...
Page 475 07 12.25 CY73031 CY73032...
Page 476 07 12.25 SECTION SPECIFICATIONS Dimensions and weights ........Engine .
Page 477: Dimensions And Weights
07 12.25 Dimensions and weights Towing capacity (trailer weight + cargo Overall length mm (in.) 4805 (189.2) weight), kg (lb.): Overall width mm (in.) 1910 (75.2) For weight carrying hitch 2268 (5000) ∗ 2 or 3, 4 Also for weight distributing hitch 1820 (71.7) ∗...
Page 478: Engine
07 12.25 Engine Fuel Service specifications Model: Fuel type: ENGINE 1GR−FE and 2UZ−FE Unleaded gasoline, Octane Rating 87 Valve clearance (engine cold), mm (in.): (Research Octane Number 91) or higher. Type: 4.0 L V6 (1GR−FE) engine 1GR−FE engine Fuel tank capacity, L (gal., Imp. gal.): Intake 0.15—0.25 (0.006—0.010) 6 cylinder V type, 4 cycle, gasoline...
Page 479 07 12.25 “Toyota Genuine Motor Oil” is used in COOLING SYSTEM BATTERY your Toyota vehicle. Use Toyota approved ∗ Total capacity, L (qt., Imp. qt.): Open voltage at 20_C (68_F): “Toyota Genuine Motor Oil” or equivalent 4.0 L V6 (1GR−FE) engine 12.6—12.8 V...
Page 480 Four−wheel drive models ∗ : The fluid capacity is the quantity of ref- Front (1.6, 1.3) Please contact your Toyota dealer for fur- erence. If replacement is necessary, Rear 3.05 (3.2, 2.7) ther details. contact your Toyota dealer.
Page 481 07 12.25 DIFFERENTIAL (4.7 L V8 [2UZ−FE] en- BRAKES gine) Minimum pedal clearance when depressed Oil capacity, L (qt., Imp. qt.): with the force of 490 N (50 kgf, 110 lbf) with the engine running, mm (in.): Two−wheel drive models 54 (2.1) 3.05 (3.2, 2.7) Pedal free play, mm (in.):...
Page 482: Tires
07 12.25 Tires Tire size, cold tire inflation pressure and wheel size: Cold tire inflation pressure kPa (kgf/cm or bar, psi) Tire size Wheel size Front Rear Spare ∗ 1 P265/70R16 111S 220 (2.2, 32) 220 (2.2, 32) 220 (2.2, 32) ∗...
Page 483: Fuses
07 12.25 Fuses 11. EFI NO.2 10 A: Multiport fuel injection system/sequential multiport fuel injec- tion system 12. HEATER NO.2 7.5 A: Air conditioning system CY80013 CY80010 13. AIRSUS NO.2 10 A: Rear height con- trol air suspension 14. SEAT HEATER 25 A: Seat heaters 15.
Page 484 07 12.25 19. ECU−B 10 A: Anti−lock brake system, 29. IGN 10 A: Multiport fuel injection sys- 39. ECU−IG 10 A: Shift lock control sys- traction control system (two−wheel tem/sequential multiport fuel injection tem, power windows, anti−lock brake drive models), active traction control system, anti−lock brake system, trac- system, traction control system (two−...
Page 485 07 12.25 43. TAIL 10 A: Tail lights, license plate 51. BATT CHG 30 A: Trailer sub battery lights, parking lights, instrument panel 52. TOWING Trailer lights (tail light control, multiport fuel injection lights) system/sequential multiport fuel injec- 53. ABS MTR 40 A: Anti−lock brake sys- tion system, instrument panel lights, tem, traction control system (two−wheel meter and gauge, glove box light...
Page 486: For Owners
07 12.25 SECTION FOR OWNERS Reporting safety defects for U.S. owners ..... . Seat belt instructions for Canadian owners (in French) .
Page 487: Reporting Safety Defects For U.s. Owners
However, NHTSA cannot become involved in individual problems between you, your dealer, or Toyota Motor Sales, U.S.A., Inc.
Page 488 07 12.25...
Page 489 07 12.25...
Page 490 07 12.25 U −4 Quick index D If a service reminder indicator or warning buzzer comes on ..D If your vehicle will not start ........D If your engine stalls while driving .
Page 491 The Toyota authorized Repair Manual is packed with literally everything you need to know to perform your own maintenance in virtually every area of your new vehicle.
Page 492 The repair manual outlines exactly what main- The repair manual for 4RUNNER may be pur- tenance is required and clearly explains how to do the chased from any Toyota dealer or the Material work yourself step−by−step. Distribution Center. To purchase the repair...

Toyota 2008 4Runner Owner's Manual

Section

1 2 Section −

1 3 Section −

1 4 Section −

1 5 Section −

1 6 Section −

1 7 Section −

1 8 Section −

1 9 Section −

1 10 Section −

2 Section

3 Section

Section

5 Section

Quick Links

Occupant restraint systems

Chapters

Related Manuals for Toyota 2008 4Runner

Summary of Contents for Toyota 2008 4Runner