Appendix B: Programming Lcd Keypads - DSC Power632 Installation Manual

Appendix B: Programming LCD Keypads

If you have an LCD5500Z keypad, additional programming is required for proper operation. The following is a description of the
available programming options and their accompanying programming sections:
How to Enter LCD Programming
Follow the programming procedure as outlined in Section 4 by pressing [*][8][Installer's Code]. Press the [*] key. Enter the two
digit section number to be programmed.
Programmable Labels – Sections [01] - [08], [33], [34], [40], [44], [51], [52]
Zone labels and other LCD display identifiers can be customized to make operation of the system easier for the end user. The fol-
lowing procedure should be used for creating all LCD labels:
• Enter installer programming. Enter the number corre-
sponding to the label to be programmed.
• Use the arrow keys (<>) to move the underline bar under-
neath the letter to be changed.
[1] - A, B, C, 1 [2] - D, E, F, 2
[6] - P, Q, R, 6 [7] - S, T, U, 7
• When the required letter or number is displayed use the
arrow keys (<>) to scroll to the next letter.
[01] to [32] Zone Labels (14 Characters)
Default: "Zone 1" - "Zone 32"
Record zone labels on page 29
[33] Fire Alarm Label (14 Characters)
Default: "Fire Zone"
[34] System Label (14 Characters)
Default: "System"
[40] to [48] [*][7][1-4] Command Output Option Labels (14 Characters)
[40] Default: "Command O/P 1"
[44] Default: "Command O/P 2"
[46] Default: "Command O/P 3"
[48] Default: "Command O/P 4"
[51] Fail to Arm Event Message
Default: "System Has Failed to Arm"
[52] Alarm When Armed Event Message
Default: "Alarm Occurred While Armed < >"
[60] First User Display Mask
Default Option
ON 1
I_______I
ON 2
I_______I
ON 3
I_______I
ON 4
I_______I
ON 5
I_______I
ON 6
I_______I
ON 7
I_______I
ON 8
I_______I
[3] - G, H, I, 3 [4] - J, K, L, 4
[8] - V, W, X, 8 [9] - Y, Z, 9,0
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
ON
Hold [P]anic Keys Prompt ON
Zone Bypassing Prompt ON
Troubles Prompt ON
Alarm Memory Prompt ON
Door Chime Control Prompt ON
Access Codes Prompt ON
User Functions Prompt ON
Output Control Prompt ON
• Press the number key [1] to [9] corresponding to the letter
you require. The first time you press the number the first
letter will appear. Pressing the number key again will dis-
play the next letter. Refer to the following chart:
[5] - M, N, O, 5
[0] - Space
• When you are finished programming the zone label, press
the [*] key, scroll to "Save," then press [*].
• Continue from Step 2 until all labels are programmed.
OFF
Hold [P]anic Keys Prompt OFF
Zone Bypass Prompt OFF
Troubles Prompt OFF
Alarm Memory Prompt OFF
Door Chime Control Prompt OFF
Access Codes Prompt OFF
User Functions Prompt OFF
Output Control Prompt OFF
45