Service Manual Model No.: Chapter 1: General Information 1-1. Table of Contents 1. General Information................1-1. Table of Contents 1-2. General Guidelines 1-3. Important Notice 1-4. How to Read this Service Manual ..................3. Location of Controls and Components........... 3-1. Board Location 3-2.
Page 3
Service Manual Model No.: 9. Trouble-shooting………….............. 9-2. Main Board Failure Check 9-3. Panel Failure - 02 -...
Service Manual Model No.: 1-2. General Guidelines When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Service Manual Model No.: 1-3-6 Safety Check after Repairment in the original positions, or whether there are the positions which are deteriorated around the serviced places serviced or not. Check the insulation between the antenna terminal or external metal and the AC cord plug blades. And be sure the safety of that. General Servicing Precautions 1.
Service Manual Model No.: Electrostatically Sensitive (ES) Devices Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
Service Manual Model No.: 1-3-8. Photo used in this manual The illustration and photos used in this Manual may not base on the final design of products, which may differ from your products in some way. 1-4. How to Read this Service Manual Using Icons: each icon is described in the table below: Note:...
Page 8
Service Manual Model No.: Model LE55B1381a Screen Size 54.6inch Aspect Ratio 16:9 Resolution 1920x1080 6 (GRAY TO Response Time (ms) GRAY) Angel of View Color Display 16777216 No. of Preset Channels 203 OSD Language English/France/Spaish Color System NTSC Audio System Audio Output Power 10W×2...
Service Manual Model No.: 3. Location of Controls and Components 3-1 Board Location Part Number Description Main board A Board 0113070686 0113050420 B Board Power board 0113060163 C Board 120HZ control board 3-2 Main Board J10: J4:IR&KEY J6:PANEL J5:POWER J3:DVD J8:AUDIO HDMI BOARD...
Page 10
Service Manual Model No.: 3-2-1 Function Description: Main Board Process signal which incept from exterior equipment then translate into signal that panel can display. Main board connector Power connectors (J1, J5) Notes: J1-Pin 4: Backlight on/off: The system can turn on or turn off the backlight of TFT LED Panel through the power supply unit path.
Page 11
Service Manual Model No.: Keypad and remote connector (J4) Pin number Signal name Description Ground Power key CH- key CH+ key Vol- key Vol+ key Meny key TV/AV key Ground IR Receive LED_G Green Indicator LED_R Red Indicator +5V DC Power Supply - 10 -...
Service Manual Model No.: Speaker connector J12 Pin number Signal name Description Audio Right+channel Output Audio Right- channel Output Audio Left- channel Output Audio Left+channel Output 3-3. Power Board Pin-CON1 Connection And Function NO . P in C onnec tion Func tion AC -N AC INP UT NUTUR E...
Service Manual Model No.: 3-4. LED Panel V546H1-LE5 - 12 -...
Page 14
Service Manual Model No.: 3-5 Interface Connec t ions CNF2 Connector Pin Assignment(187059-51221(P-two) or equivalent) Symbol Description Symbol Descrip tion Ground CH2[0]- Second pixel Odd LVDS Signal- Second pixel Odd LVDS Signal+ CH2[0]+ Second pixel Odd LVDS Signal- CH2[1]- Second pixel Odd LVDS Signal+ CH2[1]+ CH2[2]- Second pixel Odd LVDS Signal-...
Page 15
Service Manual Model No.: CNF3 Connector Pin Assignment(187059-51221(P-two) or equivalent) Symbol Description Symbol Descrip tion CH3[4]- Ground Third pixel Odd LVDS Signal- CH3[4]+ Third pixel Odd LVDS Signal+ Four pixel Odd LVDS Signal- CH4[0]- Four pixel Odd LVDS Signal+ CH4[0]+ CH4[1]- Four pixel Odd LVDS Signal- Four pixel Odd LVDS Signal+...
Page 16
Service Manual Model No.: CN1(Header):CI0114M1HR0-LA(CviLux) +24V Normal (3.3V) Status Abnormal(0V) Extemal PWM E_PWM Control Ixtemal PWM I_PWM Control BLON BL ON/OFF Note(1)Pin12:Extemal PWM control (use pin 12):Pin 13 must open. Note(2)Pin13:Intemal PWM control (use pin 13):Pin12 must open. Note(3)Pin12 and Pin13 can’t open in the same period. 3-6 120HZ Control Board CON1 CON2...
Service Manual Model No.: 4. Disassemble and assemble Front Back 4-1, Remove the10 screws as below picture - 15 -...
Page 18
Service Manual Model No.: 4-2, Remove the 21 screws on the back cabinet 4-3, Remove the 4 screws of the fixing board on the back cabinet. 4-4, Remove the 2 screws as below picture - 16 -...
Page 19
Service Manual Model No.: 4-5, Remove the 7 screws on the fixing board 4-6,Remove the 4 screws as below picture - 17 -...
Page 20
Service Manual Model No.: -7, Remove the 4 screws fixing the power board. 4-8,Remove the 2 screws as below picture - 18-...
Page 21
Service Manual Model No.: 4-9,Remove the 1 screws as below picture 4-10, Remove the 6 screws fixing the side iron stick. - 19 -...
Service Manual Model No.: 5. Installation Instructions 5-1 External Equipment Connections Accessories PICTURE AUDIO MTS/SAP SLEEP INPUT MENU MUTE ENTER VOL+ EXIT RECALL USB PLAY/PAUSE STOP REPEAT PREV NEXT DISPLAY GUIDE FAVORITE CH.LIST Battery User GUIDE Remote Control Antenna Connection Connect one end of a coaxial cable (not included) to the ANT IN jack on the back of your TV/DVD combo, then connect the other end of the cable into the antenna or cable TV wall outlet.
Page 24
Service Manual Model No.: AV Input Connection Note: All cables shown are not included with the TV. RCA Video Cable RCA Audio Cable DVD or VCR - Connect the VIDEO and AUDIO output jacks on the DVD or VCR to the AV IN jacks on the TV set with a RCA cable.
Page 25
Service Manual Model No.: PC Connection Note: All cables shown are not included with the TV. - If using a sound card, adjust the PC sound as required. - Set the video resolution of your PC audio PC to 1024x768, 60Hz on its cable original monitor.
Service Manual Model No.: 5-2 HDMI Connections When the source device(DVD player or Set Top Box) supports HDM How To Connect 1. Connect the source device to HDMI port of this TV with an HDMI cable(not supplied with this product). 2.
Page 27
Service Manual Model No.: Cable sample HDMI Cable (not supplied with the product) HDMI to DVI Cable ( not supplied with the product) Analog Audio Cable (Stereo to RCA type) (not supplied with the product) - 25 -...
Page 28
Service Manual Model No.: Power source TO USE AC POWER SOURCE Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug into a standard polarized AC outlet. NOTES: Use the attached power cord only. electrician replace the obsolete outlet.
Service Manual Model No.: 6. Operation Instructions Basal information 6-1 Front panel controls 2). The functions of the buttons: INPUT: Press to display the input source menu. MENU: Press to display the OSD menu, press again to exit the menu. VOL+/-: Press to adjust the volume.
Service Manual Model No.: 6-3 Setting Up Your Remote Control 1: POWER TO set the TV to standby or power on. AUDIO PICTURE 2:PICTURE ress repeatedly to cycle through the available. MTS/SAP SLEEP 3:CCD Press to display the closed caption. 4:ARC Adjust picture size.
Service Manual Model No.: 8.TV Operation 8-1.TV OSD Menu Press MENU button to display the OSD menu as below: Main menu Picture, Audio, Time, Setup, Lock, Channel Submenu (Picture menu for example) HDMI CEC Hint you should operate the OSD menu according to the hint.
Page 42
Service Manual Model No.: CEC mode: Turn on/off the CEC mode. TV Auto Power: The connected device(DVD) will be powered on when the TV’s on. TV Auto Switch: The TV will be in the source which is suit for the connected device(DVD).
Page 43
Service Manual Model No.: Time menu Sleep timer: You may set the automatic shutdown timer choosing from 5 to 240 minutes, or deactivate this function. Time zone: Select between Pacific,Alaska,Hawaii,Eastern,Central and Mountain Daylight Saving Time: Select between On and Off. Clock: User can not change time manually during DTV mode, for time is from signal source directly.
Page 44
Service Manual Model No.: Setup menu Menu Language: Select OSD menu language. Zoom Mode: Select the zoom mode between 16:9, 16:9 zoom, 4:3, 4:3 zoom. Noise reduction: Select the noise reduction mode between Strong, Off, Weak and Middle. PC SETUP: If the video input signal comes from your PC, you may adjust the V-Position, H-Position, Clock, Phase or even perform an Auto adjustment.
Page 45
Service Manual Model No.: Lock menu You must enter the password to gain access to the Lock menu. The default password is 0000. You may modify the following options: Change password: Change the password,you must enter the new password twice to confirm it.
Page 46
Service Manual Model No.: 7. Channel menu Air/Cable: Allow you to select antenna between Air and Cable. If you selet “Cable”, the following items(Favorite, Show/Hide, Channel NO, Channel Label and DTV Signal) are unable to use. Auto Scan: Enter the Auto Scan menu to start auto scan. If you select “Cable”...
Service Manual Model No.: 8-2 Upgrade software Haier MST318 F/W upgrade with USB SOP Step 1: Ready for F/W Upgrade 1.1 Prepare a USB memory . 1.2 Copy the software file(merg.bin)from your computer to the USB memory,and remove it from computer’s USB port! Step 2: F/W Upgrade 2.1 AC ON...
Service Manual Model No.: 8-3 Factory menu 1. You can press "MENU-8-8-9-3" to go into factory setting. Presse the key "exit" to shut the factory setting. content: 1:Version Info:the information about the TV and software - 46-...
Page 49
Service Manual Model No.: 2: ADC setup: set ADC value of YUV,VGA. It can also be auto-set. Adopt 100% color bar to yuv and Checkerboard signal to vga. adjust the color temperature and white balance of each signal source. Color Temp: - 47 -...
Page 50
Service Manual Model No.: 4: Video Quality:change value of each picture mode’s options 5:Sound Quality:change value of each sound mode’s options - 48 -...
Page 51
Service Manual Model No.: 6:Curve Setting:change Video and Sound curve (1):Video curve Setting (2):Sound curve Setting - 49 -...
Page 52
Service Manual Model No.: 7:OverScan:Change the display coordinate of the source single 8:Aging Mode:made the TV into aging mode.You can out the mode only use the Key Power 9:SW Upgrade:upgrade the software 10:Shipment:reset all the amend except ADC - 50 -...
Service Manual Model No.: 9-2. Main board failure check Power Units Problem Solving In stand-by condition, Check pin 10of J5, Whether got 5V Whether main board testing TP8point got 3.3V? Normal booting Check U9 power Check external network power suppply After power on, check whether pin 3/4 of J5got 5v, pin 1 of J5 got 12v, testing...
Page 55
Service Manual Model No.: State: No Sound No sound If there is anyaudio signal input or Whether amplifier power supply is normal? Whether the volume, MUTE setting is normal? Whether there is signal output from J2? Whether there is signal input in U4 TPA3110 3/12? Check whether there is signal...
Page 56
Service Manual Model No.: state:black screen Black screen Whether the voltage that power panel supply to Inverter is normal? Check the socket that controls Inverter, whether the voltage output from pin 4 of J1 is in low level? Check and repair the Check the external power supply circuit Inverter is broken or network that controls...
Page 57
Service Manual Model No.: 9-3. Pannel failure Failure Mode Part Name Description Phenomena Failure cause Block Defect :TCP cracking or cracking Dim or L/D :TCP Sunken V B/D Vertical bar :TCP lead cracking :ACF bonding short :Awful environment and something electric enter V Dim Vertal gray line into LED...
Page 58
Service Manual Model No.: Failure Mode Part Name Description Phenomena Failure cause White Screen B/L normal, only white screen display M a y b e c a u s e d by surge current Black Screen B/L normal, and EDS only Black screen display FIIcker...
Page 59
Service Manual Model No.: Failure Mode Part Name Description Phenomena Failure cause Mechanlcal When Caused Nolse turn panel,appear b y M e c h a n i c a cacophony noise of backlight unit Ripple Connectric circle Causeed by between mechanism and pannel B/L off...
Page 60
Service Manual Model No.: Failure Mode Part Name Description Phenomena Failure cause Brightness B/L unit badness at bottom of LCM Light leakage brighter than normal B / L b r i g h t n e s s Sheet in B/L unit Mechanlcal or B/ asymmetric is uneven...
Page 61
Sincere Forever Haier Group Haier Industrial Park, No.1, Haier Road 266101, Qingdao, China http://www.haier.com Printed in China...