Motorola MBP9 User Manual

User's Guide
Digital Audio Baby Monitor
Model: MBP9
The features described in this User's Guide are subject to modi cations without prior notice.
1. Safety Instructions
WARNING:
STRANGULATION HAZARD - Keep the Unit and adapter cords more
than 1 metre from the cot and out of baby's reach. NEVER place the Unit
or cords within the cot. SECURE the cords more than 1 metre away from
baby's reach. Never use extension cords with AC Adapters. Only use the
AC Adapters provided.
BABY UNIT SET UP & USE:
● Determine a location for the BABY UNIT that will provide the best
view of your baby in his/her cot.
● Place the BABY UNIT on a flat surface, such as a dresser, bureau, or
shelf or mount the Unit to a wall securely using the keyhole slots
under the stand.
● NEVER place the baby unit or cords within the cot.
WARNING
This Digital Audio Baby Monitor is compliant with all relevant standards regarding
safe to use. Therefore, always read the instructions in this User's Guide
carefully before using the device.
• Adult assembly is required. Keep small parts away from children when
assembling.
• This product is not a toy. Do not allow children to play with it.
• This Baby Monitor is not a substitute for responsible adult supervision.
• Keep this user's guide for future reference.
• Keep the cords out of reach of children.
• Do not cover the Baby Monitor with a towel or blanket.
Welcome...
to your new Digital Audio Baby Monitor!
Thank you for purchasing the MBP9. This baby monitor uses digital
communication which ensures that you can hear your baby clearly
without any distracting noise or interference.
Please retain your original dated sales receipt for your records. For
warranty service of your Motorola product, you will need to provide a
is not required for warranty coverage.
For product related questions, please call:
UK 0845 218 0890
ROI 08187 62092
This User's Guide provides you with all the information you need to get
the most from your product.
Before you can use the baby monitor, you'll need to insert and fully
charge the batteries on the Parent unit. Please read the Safety
Instructions in section 1 "Safety Instructions" before you install the units.
Got everything?
• 1 x Parent unit
• 1 x Baby unit
• 1 x Rechargeable battery pack for the Parent unit
• 1 x Power adapter for the Parent unit
• 1 x Power adapter for the Baby unit
• Test this monitor and all its functions so that you are familiar with it prior to
actual use.
• Do not use the Baby Monitor in damp areas or close to water.
• Do not install the Baby Monitor in extreme cold or heat, direct sunlight, or
close to a heat source.
• Only use the chargers and power adapters provided. Do not use other
chargers or power adapters as this may damage the device and battery
pack.
• Only insert a battery pack of the same type.
• Do not touch the plug contacts with sharp or metal objects.
• Connect the power adapters to easily accessible electrical outlets.
CAUTION
You chance the risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to their instructions.
2. Getting started
2.1 Baby unit power supply
2.1.1 Connect the small plug of the power adapter to the pow er connector
on the baby unit and the other end of the adapter to the mains socket
(100-240Vac~50/60Hz).
NOTE
Only use the enclosed power adapter (5V DC /600mA).
5
Overview of your Parent unit
A B
7
1
6
2 5
3
4
8
1. Link indicator LED 7. Volume indicator LEDs
2. Volume down button 8. Power adapter connector
9. Belt clip
4. Speaker 10. Battery cover screw
5. Volume UP button 11. Battery cover
6. Power (ON / ) LED
Overview of your Baby unit
C D
12
15
FIND
14
13
12. Power LED 14. Power adapter connector
13. Microphone 15. FIND key
2.2 Parent unit battery installation
Black
The Parent unit can be used with either the rechargeable battery pack (2.4V
600mAh Ni-MH rechargeable battery pack supplied) or via the power adapter
supplied.
WARNING
Never use ordinary, non-rechargeable batteries. The power mains adapter
provides a charging function, and non-rechargeable batteries may burst and
cause damage!
NOTE
The Ni-MH rechargeable batteries must be charged for 16 hours before using
the Parent unit without the mains power.
We recommend the rechargeable batteries are installed, so that the unit
continues to work in the event of a mains power failure.
1. Using a screwdriver, turn the screw of the battery cover on the back of the
parent unit 90 degrees in a counterclockwise direction. Remove the battery
cover.
NOTE
Rotate the belt clip to its hanging position to make it easier to access the battery
compartment.
6
Table of contents
1. Safety Instructions .....................................................................................5
2. Getting started ..........................................................................................6
2.1 Baby unit power supply...................................................................................6
9
2.2 Parent unit battery installation ........................................................................7
10
2.3 Parent unit power supply ............................................................................... 8
2.4 Link...................................................................................................................9
11
2.5 Paging .............................................................................................................9
3. Using the MBP9 .........................................................................................9
3.1 Volume adjustment on the Parent unit ...........................................................9
4. Disposal of the device (environment) ...................................................10
5. Cleaning ..................................................................................................10
6. Help .........................................................................................................10
7. General Information ................................................................................11
Do not try to turn the screw further than the OPEN position marked on the
cover.
2. Insert one battery pack with 2 AAA size Ni-MH rechargeable batteries.
3. Close the battery compartment and turn the screw 90 degrees back in a
clockwise direction.
4. Press and hold . The Power (ON /
has battery power.
Red
NOTE
When the battery level is low, the red power LED will flash and the parent unit
will emit a warning beep once every minute. If the baby unit loses power or
goes out of range, the link will be lost and the parent unit will emit a warning
beep every 20 seconds and the green link LED on the parent unit will continue
to flash.
WARNING
Keep batteries away from small children.
Remove the batteries if this device is not going to be used for a long period of
time.
2.3 Parent unit power supply
1. Connect the small plug of the power adapter to the power connector on
the parent unit and the other end of the adapter to the mains socket
(100V-240V ~ 50/60Hz).
NOTE
Only use the enclosed adapter (5V DC/600mA).
2. Press and hold . The Power (ON /
LED will illuminate red if it only has mains
power.
unit.
7
) LED will illuminate red if it only
)
8