HCD-EA20 3 7 63 1515 0 SERVICE MANUAL AEP Model UK Model Ver 1.0 2003. 10 HCD-EA20 is the amplifier, DVD/CD and tuner section in DAV-EA20. Model Name Using Similar Mechanism HCD-SA30 Mechanism Type CDM77A-DVBU20 Optical Pick-up Name TDP022W...
Page 2
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
HCD-EA20 SECTION 1 SERVICING NOTE 3 7 63 1515 0 MODEL IDENTIFICATION NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK — BACK PANEL — OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc.
Page 5
HCD-EA20 3 7 63 1515 0 • Service position of UCOM board UCOM board J-2501-212-A (1mm/5P/L300) J-2501-200-A (1mm/11P/L300) J-2501-198-A (1mm/17P/L300) L 13942296513 • Service position of AMP board AMP board u163 http://www.xiaoyu163.com...
Page 6
HCD-EA20 3 7 63 1515 0 • Service position of DMB03 board UCOM board J-2501-167-A (1.25mm/17P/L300) DMB03 board L 13942296513 DMB03 board UCOM board J-2501-188-A (1mm/15P/L400) J-2501-075-A (1mm/21P/L500) u163 http://www.xiaoyu163.com...
HCD-EA20 SECTION 2 GENERAL 3 7 63 1515 0 This section is extracted from instruction manual. Front Panel A "/1 (power) (21) H PHONES jack (21) B STANDBY indicator (21) I ./>, PREV/NEXT, PRESET –/+ (22, 23, 52, 54)
Page 8
HCD-EA20 3 7 63 1515 0 L ./>, PREV/NEXT, TV CH –/+, Remote PRESET –/+ (22, 23, 51, 52, 53, 54) M H PLAY/SELECT (21, 23, 28, 29, 30, N DVD TOP MENU/ALBUM– (23, 25, 26) O DVD DISPLAY (25, 26, 30, 32, 37, 38, 39,...
HCD-EA20 SECTION 3 DISASSEMBLY 3 7 63 1515 0 • The equipment can be removed using the following procedure. CASE FRONT PANEL DVD MECHANISM UCOM BOARD I/O BOARD SECTION (CDM77A-DVBU20) PANEL BOARD, DMB03 BOARD TRAY (AU) STANDBY BOARD AMP BOARD,...
HCD-EA20 3 7 63 1515 0 3-8. DVD MECHANISM (CDM77A-DVBU20) 7 CD lid 1 two screws (+BVTP2.6 × 8) 6 two claws 5 w ire (flat type) 29p (CN002) 3 three screws (sumitite 3 × 6) 8 DVD mechanism...
HCD-EA20 3 7 63 1515 0 3-10. MS-128 BOARD 1 belt 3 MS-128 board 2 four claws L 13942296513 3-11. BASE UNIT 1 belt 7 chuck cam 3 puley 5 two claws 4 gear 2 claw 6 base unit u163 http://www.xiaoyu163.com...
HCD-EA20 SECTION 4 TEST MODE 3 7 63 1515 0 [KEY TEST] [AMP TEST MODE] * Key check and volume check. * SOUND FIELD and volume function is tested. Note: In advance of Amp test mode SOUND FIELD is set except AFD Procedure: AUTO.
Page 19
HCD-EA20 3 7 63 1515 0 [COLOR SYSTEM SELECTION] [GENERAL DESCRIPTION] * Color system can be changed to PAL or NTSC. The Test Mode allows you to make diagnosis and adjustment easily Procedure: using the remote commander and monitor TV. The instructions, Set the FUNCTION to DVD.
Page 20
HCD-EA20 3 7 63 1515 0 0-1. All (All items continuous check) 0-2-4. Model Type This menu checks all diagnostic items continuously. Normally, all Model name is displayed. (DAV-EA20) items are checked successively one after another automatically unless an error is found, but at a certain item that requires judgment 0-2-5.
Page 21
HCD-EA20 3 7 63 1515 0 1-1. DVD-SL (single layer) 24. Auto track gain adjust Press the key on the remote commander and insert a DVD single Search Check layer disc following the message. Then the adjustment will be made 25.
Page 22
HCD-EA20 3 7 63 1515 0 DRIVE MANUAL OPERATION 2-1. Disc Type Note: This mode is used for design, and not used in service fundamen- tally. Disc Type On the Test Mode Menu screen, press the key on the remote Disc Type Select commander, and the Operation Menu will be displayed.
Page 23
HCD-EA20 3 7 63 1515 0 2-3. Track/Layer Jump 2-1-3. Disc Type CD It sets up so that it may judge as a disc type of specification of the disc with which the set was inserted. Track/Layer Jump : CD disc (normal speed, 12 cm) FWD R.Lj L0>L1...
Page 25
HCD-EA20 3 7 63 1515 0 MECHA AGING • Code list of Emergency History 10: Communication to RF AMP (IC001) failed. On the Test Mode Menu screen, selecting executes the aging of 11: Each servo for focus, tracking, and spindle is unlocked.
HCD-EA20 SECTION 5 ELECTRICAL ADJUSTMENT 3 7 63 1515 0 [TEST DISC LIST] 90 to 9F : BU down operating. A0 to AF : Opening/closing the shutter. Or stationary state in Use the following test disc on test mode.
Page 28
HCD-EA20 3 7 63 1515 0 THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For schematic diagrams. For printed wiring boards. Note: Note: • All capacitors are in µF unless otherwise noted. pF: µµF •...
HCD-EA20 – VIDEO SECTION – 3 7 6 3 1 5 1 5 0 IC256 RF SERVO D-FF SECTION J102(1/2) VIDEO IC151 VIDEO IN VIDEO INPUT SELECTOR IC106 VIDEO SELECTOR J101 (1/2) 1 IN1 VIDEO IC251 14 2B OUT2 VIDEO OUT 75Ω...
HCD-EA20 6-7. PRINTED WIRING BOARD – DMB SECTION (SIDE A) – • See page 27 for Circuit Boards Location. • : Uses unleaded solder. 3 7 6 3 1 5 1 5 0 N O T U S E D...
HCD-EA20 6-22. PRINTED WIRING BOARD – AMP/SUB TRANSFORMER SECTION – • See page 27 for Circuit Boards Location. • : Uses unleaded solder. 3 7 6 3 1 5 1 5 0 U C O M D M B 0 3...
HCD-EA20 3 7 63 1515 0 6-27. IC BLOCK DIAGRAMS – AMP BOARD – IC301 STK402-920 L 13942296513 IC401 STK403-030 PRE DRIVER PRE DRIVER IC CH1 IC CH2 BIAS CIRCUIT u163 http://www.xiaoyu163.com...
Page 60
HCD-EA20 3 7 63 1515 0 IC501,521,551 NJM4580E(TE2) IC502,522,552 M62429P VIN2 VOUT2 CLOCK A OUT VR 2 B OUT A –IN VOL AMP 2 VREF LOGIC CONTROL VOL AMP 1 A +IN B –IN REF AMP VR 1 B +IN V–...
Page 61
HCD-EA20 3 7 63 1515 0 IC302 PCM1609KPTR Power Supply System Clock VCC3 SCKI Manager SCKO Output Amp and AGND3 Low-pass Filter VCC4 Output Amp and Low-pass Filter AGND4 Enhanced Output Amp and Oversampling Multi-level LRCK Low-pass Filter VOUT8...
Page 63
HCD-EA20 3 7 63 1515 0 IC903 BR24L16F-WE2 1 A0 16 K bit EEPROM ARRAY 11 bit 8 bit TEST 2 A1 ADDRESS SLAVE WORD DATA 11 bit DECODER ADDRESS REGISTER REGISTER START STOP 3 A2 CONTROL CIRCUIT HIGHT VOLTAGE...
HCD-EA20 3 7 63 1515 0 6-28. IC PIN FUNCTION DESCRIPTION • IC207 ZIVA5X-C1F (DVD SYSTEM PROCESSOR)(DMB03 BOARD) Pin No. Pin Name Description VDDP — Power supply terminal (+3.3V) (I/O signal) Address bus HD15 Data bus (address signal multiplexed)
Page 72
HCD-EA20 3 7 63 1515 0 Pin No. Pin Name Description TCK signal input RESET ZIVA reset input BUS CLK Not used — Ground terminal (inside core) — Power supply terminal (+1.8V) (inside core) Address bus 3 Address bus 2 GNDP —...
Page 73
HCD-EA20 3 7 63 1515 0 • IC701 CXD1882R (DVD DECODER)(DMB03 BOARD) Pin No. Pin Name Description 1, 2 D5, D6 Two-way data bus with the mechanism controller — Ground terminal (digital system) Two-way data bus with the mechanism controller Address signal input from the mechanism controller —...
Page 74
HCD-EA20 3 7 63 1515 0 Pin No. Pin Name Description XPDI Not used VDDS — Power supply terminal (+5V) (digital system) 59, 60 HA0, HA2 Not used — Ground terminal (digital system) 62, 63 HCS0, HCS1 Not used —...
Page 75
HCD-EA20 3 7 63 1515 0 Pin No. Pin Name Description 128, 129 VCCA3, VCCA2 — Power supply terminal (+3.3V) (analog system) Signal output from the charge pump for phase comparator PDHVCC Middle point voltage input terminal for RF PLL...
Page 76
HCD-EA20 3 7 63 1515 0 • IC901 CXP973064-232R (MECHANISM CONTROLLER)(DMB03 BOARD) Pin No. Pin Name Description NO USE Not used SDEN Serial data enable signal output to DVD/CD RF amplifier DOCTRL/ Digital out on/off control signal output to the digital signal processor ISBTEST “L”: digital out off, “H”: digital out on...
Page 77
HCD-EA20 3 7 63 1515 0 Pin No. Pin Name Description CONTROL 2 Disc tray out detection signal input terminal Not used GFS DVD Guard frame sync signal input from the DVD decoder MUTE CD Muting on/off control signal output to the digital signal processor “H”: muting on MUTE 2D Muting on/off control signal output to the motor/coil driver “H”: muting on...
Page 78
HCD-EA20 3 7 63 1515 0 µPD703260YGF-S07-JBT-A (SYSTEM CONTROLLER)(UCOM BOARD) • IC501 Pin No. Pin Name Description UNREG MONITOR Monitoring voltage input for protecting power block SUBTRANS-MONITOR Monitoring voltage input for protecting power block AVREF0 — Analog reference voltage for A/D converter AVSS —...
Page 79
HCD-EA20 3 7 63 1515 0 Pin No. Pin Name Description 62 to 68 NO-USE Not used (open) AU OUT MUTE Analog audio signal output muting control signal output NO-USE Not used (open) BVSS — Ground terminal (bus interface) BVDD —...
HCD-EA20 SECTION 7 EXPLODED VIEWS 3 7 63 1515 0 NOTE: • The mechanical parts with no reference • -XX, -X mean standardized parts, so they may The components identified by mark 0 or number in the exploded views are not supplied.
HCD-EA20 3 7 63 1515 0 7-2. FRONT PANEL SECTION not supplied not supplied not supplied not supplied L 13942296513 not supplied including S800 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-249-176-01 KNOB, VOL...
HCD-EA20 3 7 63 1515 0 7-3. CHASSIS SECTION supplied T101 F903 F902 supplied supplied supplied L 13942296513 supplied DVD mechanism section (CDM77A-DVBU20) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-249-177-01 CD (LID) A-4748-541-A DMB03 BOARD, COMPLETE (AEP,UK)
Page 83
HCD-EA20 3 7 63 1515 0 7-4. DVD MECHANISM SECTION (CDM77A-DVBU20) not supplied not supplied not supplied not supplied not supplied not supplied L 13942296513 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-243-742-01 TRAY (AU)
HCD-EA20 SECTION 8 ELECTRICAL PARTS LIST 3 7 63 1515 0 Note: • CAPACITORS • Due to standardization, replacements in the parts When indicating parts by reference number, uF : µ F list may be different from the parts specified in the please include the board name.
Page 101
HCD-EA20 3 7 63 1515 0 UCOM Ref. No. Part No. Description Remarks R674 1-216-829-11 METAL CHIP 4.7K 1/16W R675 1-216-829-11 METAL CHIP 4.7K 1/16W R676 1-216-833-11 METAL CHIP 1/16W R677 1-216-833-11 METAL CHIP 1/16W R681 1-216-813-11 METAL CHIP...
Page 102
HCD-EA20 3 7 63 1515 0 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page.