Tel 13942296513; Ic Pin Function Description - Sony XR-C4120 Service Manual

QQ
3 7 63 1515 0

6-7. IC PIN FUNCTION DESCRIPTION

• MAIN BOARD IC501 MN101C12GTC1 (SYSTEM CONTROLLER)
Pin No. Pin Name
1 AVREF–
2
3 KEYIN1
4 KEYIN0
5 D-BASS IN
6 DSTSEL
7 FUNC-SEL
8
9
10 AVREF+
11
12 OSC OUT
13
14
15
16 XT OUT
TE
L 13942296513
17
18
19 SYSRST
20 BUS-ON
21
22
23 UNICKO
24
25
26 KEYACK
27 NOSESW
28
29
30
TEL-ATT
31 TEST-IN
32 RAMBU
www
33
34 VOL-MUT
.
35
36 AMP-MUT
http://www.xiaoyu163.com
I/O
I
Reference voltage (0V) input terminal (for A/D converter)
FM and AM signal meter voltage detection input from the FM/AM tuner unit (TU1)
VSM I
(A/D input)
Key input terminal (A/D input) (LSW921 to LSW923, LSW927 to LSW933)
I
6, PRESET DISC –/+, DSPL, 6, 5, 4 n, 3 PLAY MODE, 2 SET UP, 1 N keys input
Key input terminal (A/D input) (LSW901 to LSW903, S901, LSW905, LSW906)
I OFF, SOURCE, MODE *, SEEK/AMS = 0 – + ) +, SOUND, SHIFT keys
input
I D-BASS switch (S981) input terminal (A/D input)
I
Destination setting terminal (fixed at "L" in this set)
I Setting terminal for the function select (fixed at center voltage in this set)
O
NCO Not used (open)
RC-IN0
I Rotary remote commander key input terminal (A/D input)
I
Reference voltage (+5V) input terminal (for A/D converter)
VDD — Power supply terminal (+5V)
O Main system clock output terminal (18.432 MHz)
OSC IN
I Main system clock input terminal (18.432 MHz)
GND —
Ground terminal
XT IN I Sub system clock input terminal (32.768 kHz)
O
Sub system clock output terminal (32.768 kHz)
—
GND Ground terminal
RC-IN1 I Rotary remote commander shift key input terminal "L": shift
O
Reset signal output to the SONY bus interface (IC581) "L": reset
O Bus on/off control signal output to the SONY bus interface (IC581) "L": bus on
UNISO
O Serial data output to the SONY bus interface (IC581)
UNISI I Serial data input from the SONY bus interface (IC581)
O Serial data transfer clock signal output to the SONY bus interface (IC581)
I
UNICKI Serial data reading clock signal input for the SONY bus interface Not used (open)
NCO O Not used (open)
Input of acknowledge signal for the key entry Acknowledge signal is input to accept function
I
and eject keys in the power off status On at input of "H"
Front panel block remove/attach detection signal input terminal
I
"L": front panel is attached
Battery detect signal input from the SONY bus interface (IC581) and battery detect circuit
BU-IN
I
"L" is input at low voltage
I
SIRCS Sircs remote control signal input terminal Not used (fixed at "L")
I Telephone muting signal input terminal At input of "H", the signal is attenuated by –20 dB
I Setting terminal for the test mode "L": test mode, Normally: fixed at "H"
Internal RAM reset detection signal input terminal
I
Input terminal to check that RAM data are not destroyed due to low voltage
This checking is made within 100 msec after reset Fixed at "L" in this set
System reset signal input from the reset signal generator (IC551) and reset switch (S551)
RESET I
"L": reset "L" is input for several 100 msec after power on, then it changes to "H"
x ao
y
Muting control signal output to the electrical volume (IC331)
O
Volume minimum: " ∞" output ("H" active)
i
BEEP O Beep sound drive signal output terminal
O Muting on/off control signal output to the power amplifier (IC751) "L": muting on
http://www.xiaoyu163.com
8
Function
Q Q
3 6 7 1 3
u163
.
– 31 –
2 9 9 4 2 8
1 5 0 5 8 2 9 9 4
m
co
9 9
2 8 9 9