Be sure to read this manual before servicing. To assure safety from fire, electric shock, injury, harmful radiation and materials, various measures are provided in this Hitachi liquid crystal projector. Be sure to read cautionary items described in the manual to maintain safety before servicing.
CP-X325W 1. Features High brightness, High resolution Compact size, light weight for portability RS-232C Communication Complies with VESA DDC1/2B specifications Auto-adjustment function 2. Specifications Drive system TFT active matrix Liquid crystal Panel size 0.9 inches panel Number of pixels 1024 (H) x 768 (V)
CP-X325W 3. Names of each part Main unit Speaker Zoom Knob Focus Ring Handle Hook Remote Control Sensor Power Switch Lens AC Inlet Slide Lens door (to the Power Cord) Foot Adjuster Ventilation Openings (Intake) FRONT/LEFT VIEW OF THE PROJECTOR...
CP-X325W Remote control transmitter VIDEO button STANDBY/ON button LASER button RGB button BLANK button MOUSE / RIGHT button DISK PAD Used to click the right Used to operate the mouse button. mouse shift function and left click function. POSITION button...
CP-X325W 4. Adjustment 4 - 1 Before adjusting 1. Before starting adjustment, warm up the projector 4. Perform all adjustments from the Adjustment menu. for about 10 min. (Blank white) Perform the following operations to display the 2. Set Zoom Wide to Max. and project an image a Adjustment menu.
Page 6
CP-X325W 4 - 4 PSIG adjustment (vertical stripe adjustment) Signals for internal adjustment Adjustment procedure 1. Make this adjustment after completing the adjustment in 4-3 Flicker adjustment. 2. Use DAC-P - PSIG - G: in the Adjust menu to adjust so that the vertical lines spaced every 6 dots are as inconspicuous as possible.
CP-X325W Adjustment operations (reference) 86% operation 43% operation 29% operation Adjustment Adjustment point Adjustment point point 0 14 86 100 0 14 86 100 0 14 86 100 Input signal (%) Input signal (%) Input signal (%) 14% operation 0% operation...
Page 8
CP-X325W Adjust menu Major adjustment lattice point position VIDEO C. UNIF. DAC-P GAMMA LEVEL Adjust Tone menu No. 1 Major adjustment lattice point No. Adjustment procedure 1 (when a color differential meter is used) 1 First adjust [MIN] tone [G:].
Page 9
CP-X325W 11. Then adjust [MAX] tone [R] and [B]. 14. Then measure the color coordinates for adjust- Select [No. 2] [B:] and press the [MENU SELECT] ment point [No. 10] and adjust [No. 10] [R:] and key on the Remote control transmitter to change [B:] so that the color coordinates are as follows.
Page 10
CP-X325W No. 2 deviation range No. 10 deviation range No. 3 deviation range No. 11 deviation range No. 4 deviation range No. 12 deviation range No. 5 deviation range No. 13 deviation range 3 11 3 11 No. 6 deviation range No.
Page 12
CP-X325W Power can not be turned on voltage input Disconnect at pins TSW form Power unit Open E800 on the PWB ass’y (circuit). And check Main at standby TSW short or mode? open? (TP46): +14V (TP47): +17V Short (TP48): +6V (TP49): +4.3V...
Page 13
CP-X325W Lamp does not light What is the state of Light Light Change the lamp. Lamp LAMP indicator Does lamp light? during operation? Not light Not Light Is the voltage at L817 on the PWB ass’y Main PWB ass’y Main fixed to "L"...
Page 14
CP-X325W Picture is not displayed when the RGB signal is input Check at operating mode Are signal input at each pin of PWB ass’y Signal E101 on the PWB ass’y Main? : (TP1R) : R signal : (TP1G) : G signal...
Page 15
CP-X325W Picture is not displayed when the VIDEO Signal is input Check at operating mode voltage input at pins E800 on the PWB ass’y Main? Power unit (circuit) (TP46): +14V (TP47): +17V (TP48): +6V (TP49): +4.3V Are signal input at these pins of EV01 on the PWB ass’y...
Page 16
CP-X325W No sound Check at operating mode Are signal input at these pins of EV01 on the PWB ass’y Main? PWB ass’y Signal : Audio(L) : Audio(R) PWB ass’y Main Speaker Can not control to RS-232C Check at operating mode...
CP-X325W 6. Service points • Cautions when removing the PWB Ass'y Main When removing the PWB Ass'y Main, there is danger of damaging the connector connecting cables and the PWB Ass'y Signal. 1) Disconnect 11 cables and remove 6 screws.
Page 18
Therefore, regarding these parts, you can either replace part , LCD / Lens Prism Ass'y, or send the whole unit LCD / Lens Prism Ass'y back to HITACHI, where we will replace the malfunctioning part, recondition the device and send it back to you. In that case please contact our distributor.
Page 19
CP-X325W • Loading the Battery Install the AA batteries into the remote control. 1. Remove the battery cover. Push the knob while lifting up the battery cover. 2. Loading the batteries. Make sure the plus and minus poles are correctly oriented.
CP-X325W Replacing the lamp: 1. Switch the projector OFF, remove the power cord from the power outlet, and wait at least 45 minutes for the unit to cool. 2. Prepare a new lamp. 3. Check that the projector has cooled sufficiently, and gently turn it upside down.
CP-X325W Message table On-screen display The following messages are displayed on the screen. "CHANGE THE LAMP" Lamp has 1,700 hours on it and may need to be changed. "AFTER REPLACING LAMP, RESET THE LAMP TIMER" "CHANGE THE LAMP" "AFTER REPLACING LAMP, Lamp has 1,979 hours on it.
Page 24
Preparation for wiring of Power unit Wiring of Speaker Cross the CNPOW and Speaker (R) Speaker (L) To PWB ass'y Main temperature switch lead. CNPOW Temperature temperature CN104 switch lead switch CN102 Power unit ESPR ESPL CN103 Upper view (Speaker) Position of Position of rib of front bezel.
Page 25
TAPE1 Ballast cover Folding part of the lead fixed not to pass under the PWB ass’y Main. PWB ass’y Main Folding part To PWB ass’y Main E803,E807 FOOT HOLDER Ballast cover To Power unit (circuit) Panel R CN104 Sirocco fan Hook the lead of Power unit Panel B (Ballast) at the claw.
Page 26
(1) Push in CNPOW,CNBAR and CNTH between the Foot folder and Styling not put in rib when Power unit. front bezel assembling. (1) Let CNPOW pass through (2) You may insert which connector of under the rib. To PWB ass’y CNPOW E803 and E807.
CP-X325W 12. Replacement parts list PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before replacing any of there components, read carefully, the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing.
CP-X325W 13. Option parts list Caution The cables (power cord/video cable, audio cable, RGB cable and other cables) must be used with the core set to the projector side. Use the cables which are included with the projector or specified.
Page 35
CP-X325W RS-232C communication Caution The specified RS-232C cable has the user's manual with RS-232C command table. (1) Turn off the projector and computer power supplies and connect with the RS-232C cable. (2) Turn on the computer power supply and, after the computer has started up, turn on the projector power supply.
Page 36
CP-X325W Requesting projector status (Get command) (1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes) +‘00H’+‘00H’) from the computer to the projector. (2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.
Page 37
CP-X325W Command data chart Command data Names Operation type Header Action Type Setting code BE EF 06 00 3B D3 01 00 00 30 00 00 Orange BE EF 06 00 AB D2 01 00 00 30 01 00 Green...
Page 38
CP-X325W Command data chart Command data Names Operation type Header Action Type Setting code BE EF 06 00 7C D2 02 00 07 30 00 00 Magnify Increment BE EF 06 00 1A D2 04 00 07 30 00 00...
Page 39
CP-X325W Command data chart Command data Names Operation type Header Action Type Setting code BE EF 06 00 2A D3 01 00 00 60 00 00 Power BE EF 06 00 BA D2 01 00 00 60 01 00 BE EF...
Page 40
CP-X325W Command data chart Command data Names Operation type Header Action Type Setting code BE EF 06 00 0D 83 02 00 00 21 00 00 V.Position Increment BE EF 06 00 6B 83 04 00 00 21 00 00...