Set Up An Internet Access Point For Packet Data (Gprs); Advanced Internet Access Point Settings For Packet Data (Gprs); Cable Connection - Nokia E50 User Manual

C o n n e c t i v i t y
Use PPP compress. — Select
•
Use login script — Select Yes, if your Internet service provider requires a login script, or if you want to automate your login.
•
A login script is a sequence of instructions that the system follows during the login process.
Login script — Enter the login script. This setting is available only if you have selected
•
Modem initialisation — Enter a command string for the connection setup, if required by your service provider.
•

Set up an Internet access point for packet data (GPRS)

1. Select Menu Tools
> >
2. Select Options New access
>
start with an empty access point, select
3. Define the following settings.
Connection name — Enter a descriptive name for the connection.
•
Data bearer — Select
•
Access point name — Enter the name for the access point. The name is usually provided by your service provider or network
•
operator.
User name — Enter your user name if required by the service provider. User names are often case-sensitive and provided
•
by your service provider.
Prompt password — Select
•
device memory and automate the login.
Password — Enter your password if required by the service provider. The password is often case-sensitive provided by
•
the service provider.
Authentication — Select
•
when possible.
Homepage — Enter the Web address of the page you want to display as a home page when you use this access point.
•
4. After defining the settings, select
and exit.

Advanced Internet access point settings for packet data (GPRS)

After setting up a basic Internet access point for packet data (GPRS), select
advanced settings.
Network type — Select
•
and from your device.
Phone IP address — Enter the IP address of your device. Select
•
This setting is shown only if you select
DNS address — Enter the IP addresses of the
•
or network operator. Otherwise, the name server addresses are provided automatically.
Proxy serv. address — Enter the address of the proxy server. Proxy servers are intermediate servers between a browsing
•
service and its users, which are used by some service providers. These servers may provide additional security and speed up
access to the service.

Cable connection

Install the USB data cable driver to your PC before you use a cable connection. You can use the
the USB data cable drivers.
Select Menu Connect.
> >
Using a USB data cable, you can connect your device to a compatible PC . Connect the USB data cable to the bottom of the device.
To change the device type you normally connect to your device with the data cable, press the joystick.
Select from the following:
Ask on connection — Select whether you want to be asked for the device type every time you connect the data cable to your
•
device.
PC Suite — Connect the PC Suite to your device with the data cable, and use your device as a modem.
•
Data transfer — Access and transfer data such as music or image files from your computer using the data cable connection.
•
To use the Data transfer
settings in Nokia PC Suite. Insert a memory card to your device, connect the device to a compatible computer with the USB
data cable, and select Data transfer
device and you can see it as a removable hard drive in your computer. The device will switch into the
selected. End the connection from the PC (for example, from an Unplug or Eject Hardware wizard in Windows) to avoid
damaging the memory card. After you end the connection, the device returns to the profile in which it was before using the
data transfer mode.
To save your selection, select Back.
Copyright © 2006 Nokia. All Rights Reserved.
Yes to speed up the data transfer, if it is supported by the remote PPP server.
Settings Connection Access
> >
point. To use an existing access point as a basis for the new one, select
Use default
Packet data.
Yes to enter your password each time you log into a server or
Secure to always send your password encrypted or
Options Advanced settings
>
IPv4 or IPv6 as the Internet protocol type. The Internet protocol defines how data is transferred to
Network type
Primary DNS address
Data cbl..
mode, make sure that you have not selected USB as a connection type in the Manage connections
when the device asks which mode is used. In this mode, your device acts as a mass storage
points.
settings.
to define the advanced settings or
Options
Automatic to have the network provide the device IP address.
> IPv4.
and Secondary DNS addr.
52
Use login script > Yes.
Use existing
No to save the password in your
Normal to send your password encrypted
Back
Advanced settings, and define the following
>
if required by your service provider
Data transfer
Offline
settings. To
to save the settings
without installing
profile if this is