Fellowes powershred 73ci Service Manual page 4

BASIC SHREDDING OPERATION
PAPER OR CD/CARD
1 2
Continuous operation:
10-minute maximum
NOTE: Shredder runs briefly
after each pass to clear entry.
Plug in and put
Press ( )ON to
Continuous operation beyond
disconnect power
activate (blue)
10-minutes will trigger
switch in ON (I) position
20-minute cool down period.
ADVANCED PRODUCT FEATURES
Jam Proof System
Eliminates paper jams and powers
through tough jobs.
JAM PROOF SYSTEM OPERATION*
Eliminates paper jams and powers through tough jobs.
Advanced Jam Prevention- Electronically
1
measures paper thickness to prevent paper jams:
Up to RED: Too many
sheets have been inserted.
Up to YELLOW: Productivity
is optimized.
Up to GREEN: More sheets
can be added.
If a misfeed All indicators light up and
occurs:
shredder pauses for 3-6 seconds
*100% Jam Proof when used in accordance with user manual
SAFESENSE TECHNOLOGY
®
Stops shredding immediately when hands
touch the paper opening.
SET-UP AND TESTING
1
2 3
Turn the shredder ON Touch test area and SafeSense is active and
®
( ) to activate SafeSense look for the SafeSense working properly
® ®
indicator to illuminate
For more information about all of Fellowes Advanced Product Features go to www.fellowes.com
3
4 5
or
Feed paper straight into Hold CD/card at edge, When finished
feed right side of entry
paper entry and release shredding set
and release
to OFF ( )
Energy Saving System
Patented SafeSense ® Technology
Optimal energy efficiency
Stops shredding immediately when
100% of the time – in use
hands touch the paper opening
and out of use.
2 3
Remove several sheets until
Continue 100% Jam
indicator is below red.
Proof Shredding
If illuminates after paper has been
Wait for flashing to stop after automatic correction
reversed, press reverse and remove paper.
is complete. Regular shredding will resume.
Otherwise, regular shredding will resume.
ENERGY SAVING SYSTEM
Optimal energy efficiency 100% of the
time – in use and out of use.
• Saves energy in four ways: energy-efficient electronics, jam prevention, standby mode and
sleep mode.
• Sleep Mode shuts down shredder after 2 minutes of inactivity.
WHEN IN SLEEP MODE
1 2 3
or
In sleep mode To get out of sleep mode insert paper
touch control panel
PRODUCT MAINTENANCE
OILING SHREDDER
All cross-cut shredders require oil for peak performance. If not oiled, a
machine may experience diminished sheet capacity, intrusive noise when
shredding, and could ultimately stop running. To avoid these problems, we
recommend you oil your shredder each time you empty your waste bin.
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
1 2
*Apply oil across entry Press and hold forward
( ) 2-3 seconds
* Only use a non-aerosol vegetable oil in long
nozzle container such as Fellowes 35250
Go to Support Section at www.fellowes.com or see back page of manual for useful telephone numbers.
15
TROUBLESHOOTING
Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum operating temperature and needs to cool down. This
indicator will remain illuminated and the shredder will not operate for the duration of the recovery time. See Basic Shredding Operation for more information about
the continuous operation and recovery time for this shredder.
Bin Open: The shredder will not run if the bin is open. When illuminated, close the bin to resume shredding.
15
Bin Full: When illuminated, the shredder waste bin is full and needs to be emptied. Use Fellowes waste bag 36052.
Remove Paper: When illuminated, press reverse (
SafeSense ® Indicator: If hands are too close to the paper entry, the SafeSense
is active for 3 seconds, the shredder will automatically turn off and the user must press the power button on the control panel to resume shredding.
LIMITED PRODUCT WARRANTY
Limited Warranty: Fellowes, Inc. ("Fellowes") warrants the parts of the machine to be free of defects in
material and workmanship and provides service and support for 1 year from the date of purchase by the
original consumer. Fellowes warrants the cutting blades of the machine to be free from defects in material
and workmanship for 1 year from the date of purchase by the original consumer. If any part is found to
be defective during the warranty period, your sole and exclusive remedy will be repair or replacement,
at Fellowes' option and expense, of the defective part. This warranty does not apply in cases of abuse,
mishandling, failure to comply with product usage standards, shredder operation using an improper power
supply (other than listed on the label), or unauthorized repair. Fellowes reserves the right to charge the
consumers for any additional costs incurred by Fellowes to provide parts or services outside of the country
3 4
CLEANING AUTO-START INFRARED SENSORS
Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors
may become blocked by paper dust causing the motor to run even if there is no paper present.
.
(Note: two paper detection sensors are located in the center of the paper entry)
TO CLEAN THE SENSORS
1
2 3
Turn off and unplug Locate Auto-start Dip cotton swab in
shredder infared sensor rubbing alcohol
) and remove paper. Reduce paper quantity to an acceptable amount and refeed into paper entry.
® indicator will illuminate and the shredder will stop shredding. If SafeSense
where the shredder is initially sold by an authorized reseller. ANY IMPLIED WARRANTY, INCLUDING THAT
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO
THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable for any
consequential or incidental damages attributable to this product. This warranty gives you specific legal rights.
The duration, terms, and conditions of this warranty are valid worldwide, except where different limitations,
restrictions, or conditions may be required by local law. For more details or to obtain service under this
warranty, please contact us or your dealer.
ENGLISH
Model 73Ci
4
Using cotton swab, wipe
away any contamination
from the paper sensors
®