Program And Controller Dumps - Clavia Nord Electro 3 HP User Manual

Program and Controller dumps

To dump a Program SysEx, or MIDI Controller data via MIDI, either
to another Nord Electro 3 or for recording the data into another MIDI
device, proceed as follows:
Sending program dumps
1
Connect the MIDI OUT on the Nord Electro 3 to the MIDI In on the
receiving device.
2
Set up the receiving device to accept MIDI SysEx and MIDI Con-
troller data.
3
Press Shift + MIDI and select the "Dump One" or "Dump All" menu
item using the Up/Down buttons.
4
If needed, set the receiving MIDI device to "recording mode".
5
Press the Store button to send the dump to the MIDI Out of Nord
Electro 3. The display will stop flashing once the dump has been
sent.
For the programs that use the organ sounds, the complete
settings for the sound will be dumped as MIDI SysEx but for
programs using pianos or Samples, all parameters will be sent but
NOT the actual instrument samples.
Therefore, when dumping back a program that uses a piano sound,
make sure the actual instrument samples are also available in the Nord
Electro 3. Otherwise the parameters in the SysEx message will be ap-
plied to another available piano instrument.
Sending MIDI Controller dumps
1
Set up as in steps 1 and 2 in the preceding description.
2
Press Shift + MIDI and select the 'Send CC" menu item using the
Up/Down buttons.
3
Press the Store button to send the dump to the MIDI Out of Nord
Electro 3. The Display will stop flashing once the dump has been
sent.
Receive MIDI SysEx dumps
Here is how to receive a MIDI SysEx Dump:
1
Connect the MIDI Out on the transmitting device to the MIDI IN on
the Nord Electro 3.
2
Initiate the transmission on the transmitting device.
If the dump contained all Programs (All), it will replace all programs
currently stored in the Nord Electro 3. If the dump contained only a
single program, it will be temporarily placed in the currently selected
program memory location. A dot will appear to in the lower, right corner
to indicate an unsaved edit. You will then have to store the program
manually to a memory location using the Store function (see "Storing
Programs" on page 15).
MIDI Controller list
The following is a list of the MIDI Controller numbers used for all knobs
and buttons on the front panel:
Nord Electro parameter
Drawbars - Preset 2/Upper
Drawbar 1
Drawbar 2
Drawbar 3
Drawbar 4
Drawbar 5
Drawbar 6
Drawbar 7
Drawbar 8
Drawbar 9
Drawbars - Preset 1/Lower
Drawbar 1
Drawbar 2
Drawbar 3
Drawbar 4
Drawbar 5
Drawbar 6
Drawbar 7
Drawbar 8
Drawbar 9
Organ Model Sel
Preset/Manual Sel
Perc Decay
Perc Level
Sustain Pedal
Control Pedal
Rotary Speed
Rotary Stop Mode
Vib Mode
Vib On/Off Preset 2/UP
Vib On/Off Preset 1/LOW (B3 model)
Perc On/Off
Perc Hard
Samp Attack Sel
Samp Release Sel
Clav EQ Brill On/Off
Clav EQ Treble On/Off
Clav EQ Medium On/Off
Clav EQ Soft On/Off
Inst Sel (Organ/Piano)
Piano Type
Piano Model
Piano Mono
Piano Dynamics - Electro 3 HP only
Acoustics - Electro 3 HP only
Oct Shift Organ Upper
Oct Shift Organ Lower
Oct Shift Piano
EQ On/Off
EQ Treble
EQ Mid
EQ Mid Freq
EQ Bass
Gain
Effect 1 Rate
Effect 1 Sel
Effect 1 On/Off
Effect 2 Rate
Effect 2 Sel
Effect 2 On/Off
Speaker/Comp Drive
Speaker/Comp Sel
Speaker/Comp On/Off
Reverb Wet/Dry
Reverb Sel
Reverb On/Off
Delay Rate - Electro 3 HP only
Delay Ping Pong - Electro 3 HP only
Delay On/Off - Electro 3 HP only
8 MIDI FUNCTIONS | 25
MIDI CC
16
17
18
19
20
21
22
23
24
70
71
72
73
74
75
76
77
78
9
3
88
89
64
11
82
79
84
85
117
87
95
33
34
103
104
105
106
13
12
44
83
99
98
27
28
29
115
113
116
117
114
7
63
60
69
62
61
80
111
81
86
102
96
97
92
93
94