Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Datavideo MCU-100S
Summary of Contents for Datavideo MCU-100S
-
Page 2: Warnings And Precautions
This product should only be operated from the type of power source indicated on the marking label of the AC adapter. If you are not sure of the type of power available, consult your Datavideo dealer or your local power company. -
Page 3: Standard Warranty
Certain parts with limited lifetime expectancy such as LCD Panels, DVD Drives, Hard Drives are only covered for the first 10,000 hours, or 1 year (whichever comes first). Any second year warranty claims must be made to your local Datavideo office or one of its authorized Distributors before the extended warranty expires. -
Page 4: Compatible Camera Models
Introduction The MCU-100S Remote Control Unit is designed for remote control of Sony studio or portable-type color video cameras and camcorders. The unit can be directly connected up to maximum 4 cameras or camcorders via cat.5 Ethernet cable. The unit can control a camera from a distance of up to 300 m. Easy operation, cost effective and major camera functions to be this wonderful solution. - Page 5 Example MCU-100S Set Up...
-
Page 6: Connections And Controls
Connections and Controls MCU-100S Keyboard Cameral Select Power Recorder Control Memory Store Cancel Shutter Selection Menu Gain Write/ Black Balance Master Pedestal Control Enable & Painting Adjustment USB for F/W Update Check IRIS Adjustment LED Display... - Page 7 MCU-100S Rear Side This 9 pin Mini Din can be used for confidence and composition monitoring and in some cases to view the camera’s own LCD/OSD menus. You have to connect CB-40 cable (Mini Din 1 to 4 CV out cable) to MCU-100P to have this function.
- Page 8 Using the LOAD SAVE button it is possible to transfer the current setting from one camera to another. MU-1, MU-2 can be used to store settings within the MCU-100S. DETAIL In Remote Control mode, press and light this button to enable the Detail function.
- Page 9 CANCEL In Camera Menu mode, press this button to cancel the set value. Menu When this function is enabled, the button is back lit orange and the OSD menu is shown on the LCD panel/view finder of the camera. This OSD menu may also be shown on the AD-1S’s composite output (if supported).
- Page 10 These buttons are used to adjust the level of the Master Pedestal. Enable & Painting Adjustment buttons Press the ENABLE button in the Painting area of the MCU-100S before choosing to adjust either the level of the Red and Blue Gain or the RGB Pedestal values.
- Page 11 R/B Gain and RGB pedestal values are shown on the display below in this order each time the CHECK button is pressed. If the CHECK button is pressed and held down for over two seconds the MCU-100S unit will switch in to LOCK mode. PS: CHECK function to be modifications. LED display The IRIS value, Shutter degree, speed, Gain and Filter positions can be displayed here by using the CHECK button.
-
Page 12: Seven Segment Display And Leds
Iris controls can be quickly accessed in LOCK mode by pressing down on the IRIS Dial once; press the dial again to return to full lock mode. When the Iris function is accessed in this way, if the MCU-100S unit is left idle for 3 seconds or more then the unit will automatically return to full Lock mode. - Page 13 AD-1S Camera Control Adaptor This unit allows you to operate the functions of the camera up to 300m away with the MCU-100S unit. The AD-1S adaptor connects to the MCU-100S via RJ-45 cabling to the chosen Sony camera. This adaptor changes the RJ-45 connection to a Sony CAM/BS cable and multi-pin connector.
-
Page 14: Firmware Update Procedure
Firmware update procedure From time to time Datavideo may release new firmware to either add new features or to fix reported bugs in the current MCU-100S firmware. Customers can update the firmware themselves if they wish or they can contact their local dealer or reseller for assistance should they prefer this method. -
Page 15: Specifications
Dimensions MCU-100S AD-1S Specifications Power Consumption DC 12V / 0.5A ( 15W MAX ) 350 g Weight Dimension 95mm (W) x 208mm (H) x 65.5mm (D) Input /Output RJ45 x 4 Connection Connection Distance Up to 300m (CAT-5 or CAT6)