Thank You Thank you for purchasing the all new NEO 720 class of multi-rotor aircraft. By incorporating the latest designs and the possibilty of run- ning on blade sizes from 10” to 12” propellers, the lifting capabilities and stability of the NEO 720 is unmatched.
Page 3
NEO 720 AMA RULES & REGULATIONS General 1. Model aircraft will not be flown: (a) In a careless or reckless manner. (b) At a location where model aircraft activities are prohibited. 2. Model aircraft pilots will: (a) Yield the right of way to all man carrying aircraft.
(ARF Version Only) (ARF Version Only) CNMR6001 Description Part # HWC2006 12-Inch Propeller(12 寸螺旋桨 Century HWC 2814 Motor (X2212 马达) CNMR2814A CNMR6001 Black Motor Mounting Plate( 黑色马达固定板 ) CNMR6003 L=13mm Aluminum Tube Holder(13mm 铝管固定座) CNMR6006B 20x300 Black Aluminum Tube(300mm 长黑色铝管)
Page 5
NEO 720 ARM ASSEMBLY Description Part # CNMR6010 61mm Aluminum Post(61mm 铝柱) CNMR6024B1 Upper Frame Plate( 机架上固定板) CNM3x6BHCS CNM3x6BHCS Button Head Cap Screw( 圆头内六角螺丝)M3x6 CNM3x30BHCS Button Head Cap Screw( 圆头内六角螺丝)M3x30 CNM3x8BHCS CNMR6008A1 Moveable Aluminum Tube Holder (22mm 铝管固定座 ) CNM3x30BHCS CNMR6024B1 Lower Frame Plate( 机架下固定板)
Page 7
NEO 720 DISTRIBUTION BOARD ASSEMBLY Solder the ESC’s as shown to the distribution board included with your NEO multirotor. Make sure the Positive (Red +) wire and the Negative (Black -) are correctly connected. (Optional item) Description Part # HWC 30A Multi Rotor ESC (HWC 30A 调速器)
NEO 720 LANDING GEAR ASSEMBLY Description Part # Lower Right T Joint (右下脚架) CNMR6015 CNMR6016B Aluminum Strut 200 mm (200mm 铝管 ) Upper Right T Joint (右上脚架) CNMR6015 Landing Gear Cross Boom 265mm ( 265mm 管 ) CNMR6017 CNM3x4SS CNM3x4SS Set Screw(无头内六角螺丝)M3x4...
Page 9
NEO 720 LANDING GEAR AND ELECTRONICS CNM3X8ST Description Part # CNM3X8ST Self-tapping Screw (脸捣 ) (Optional item) (Optional item) (Optional item) (ARF Version Only) Description Part # GPS Module (Optional) Multi-Rotor Controller (Optional)( 主控器) (Optional item) 8 ch Receiver 2.4G (Optional) Multi Rotor Speed Control ( 马达调速器)
Page 10
NEO 720 BUILD PHOTOS Assemble the arms as shown on page 4. Assemble the lower frame plate and aluminum Install the distributing panel hex posts on the threaded arm mounts. UPPER frame plate. NOTE: lower frame plate shown. Install the power distribution board in between...
Page 11
NEO 720 BUILD PHOTOS Assemble the GPS saver cage together, Attach the upper frame plate along with “GPS The 1/4” camera mount holes indicates the front and install on top of the upper frame plate. SAVER” to the lower frame assembly.
Page 12
1740-C Junction Ave. San Jose, CA. 95112 U.S.A. www.centuryheli.com...