KitchenAid KCGT 6010/I Instruction Manual
Hide thumbs Also See for KCGT 6010/I:

Advertisement

Quick Links

5019_718_02011_UK
30-05-2007
10:05
Pagina 1
KCGT 6010/I

Instructions for use

Advertisement

Table of Contents
loading

Summary of Contents for KitchenAid KCGT 6010/I

  • Page 1: Instructions For Use

    5019_718_02011_UK 30-05-2007 10:05 Pagina 1 KCGT 6010/I Instructions for use...
  • Page 2 5019_718_02011_UK 30-05-2007 10:05 Pagina 2...
  • Page 3: Table Of Contents

    5019_718_02011_UK 30-05-2007 10:05 Pagina 3 Warnings Safeguarding the environment Instructions for installation and use Extraction modes Installation Hood description Functioning Maintenance After-Sales Service...
  • Page 4: Warnings

    5019_718_02011_UK 30-05-2007 10:05 Pagina 4 Warnings • This appliance should not be used by children or people with limited physical or mental abilities and with no experience or knowledge of its use, unless they are supervised by someone in charge of their safety or who has taught them how to use the appliance. •...
  • Page 5: Safeguarding The Environment

    5019_718_02011_UK 30-05-2007 10:05 Pagina 5 Warnings Declaration of conformity This product has been designed, manufactured and marketed according to the following: - safety objectives of the “Low Voltage” Directive 2006/95/CE (wich replaces 73/23/CEE and subsequent amendments). - protection requirements of “EMC” Directive 89/336/EEC amended by Directive 93/68/EEC. Troubleshooting guide Hood does not work: •...
  • Page 6: Instructions For Installation And Use

    5019_718_02011_UK 30-05-2007 10:06 Pagina 6 Instructions for installation and use Follow the instructions in this manual carefully. All responsibility is denied for problems, damage or fire to the appliance resulting in failure to comply with the instructions in this manual. Extraction Modes The hood is designed to be used in two modes: Venting exhaust fumes to the...
  • Page 7: Installation

    5019_718_02011_UK 30-05-2007 10:06 Pagina 7 Installation The hood comes with plugs suitable for most walls is to be installed. Otherwise, protect the units / ceilings. You should however consult a qualified as much as possible and all the parts relating to technician to make sure the installation is suitable the installation.
  • Page 8 5019_718_02011_UK 30-05-2007 10:06 Pagina 8 Installation Fig.4 Fig. 5 • Connect an extraction pipe to the connection • Remove the grease filter and hook the filter ring on the hood and, whilst you inserting the support frame onto the hood. At this stage hood into the cabinetry, check that the connect up the electrics on the control panel extraction pipe and the electrical wire come out...
  • Page 9: Hood Description

    5019_718_02011_UK 30-05-2007 10:06 Pagina 9 Hood description Fig. 6 1. Control panel 2. Grease filter 3. Handle for unhooking the grease filter 4. Halogen bulbs Functioning Turn to maximum speed when there is a lot of steam in the kitchen. We would advise you to turn the suction on 5 minutes before starting to cook and leave it running after you have finished cooking for about another 15 minutes.
  • Page 10: Maintenance

    5019_718_02011_UK 30-05-2007 10:06 Pagina 10 Maintenance Always disconnect the power supply before carrying out any kind of maintenance work. Cleaning The hood should be cleaned regularly both inside and out (at least as often as you carry out maintenance on the grease filters). Use a damp cloth with mild cleaning products.
  • Page 11: After-Sales Service

    5019_718_02011_UK 30-05-2007 10:06 Pagina 11 After-Sales Service Before calling Customer Care Centre: 1. See if you can solve the problem yourself with the help of the “Troubleshooting guide”. 2. Switch off the hood for a few minutes and re- start it to see if the problem has cleared itself. 3.
  • Page 12: Electrical Connection For Great Britain And Ireland Only

    Socket outlet / plug (valid for both countries) If the fitted plug is not suitable for your socket outlet, please contact KitchenAid Service for further instruction. Please do not attempt to change plug yourself. This procedure needs to be carried out by a qualified technician in compliance with the manufactures instructions and current standard safety regulations.
  • Page 13 5019_718_02011_UK 30-05-2007 10:06 Pagina 13...
  • Page 14 5019_718_02011_UK 30-05-2007 10:06 Pagina 14...
  • Page 15 5019_718_02011_UK 30-05-2007 10:06 Pagina 15...
  • Page 16 5019_718_02011_UK 30-05-2007 10:06 Pagina 16 Printed in Italy 05/07 5019 718 02011...

Table of Contents