1 Introduction Thank you for purchasing the SB9015T all-in-one true-flat touch POS terminal. Bematech is committed to continuously improve product quality and provide better after-sales service. In order to take full advantage of our devices, we strongly recommend that you take the time to read this manual before diving into software solution.
Do not use harsh chemicals or strong cleaning solvents to clean the monitor screen. Wipe it clean with a soft terry cloth applied with a mild solution Do not share the same power outlet with high-power electrical appliances; keep distance from high level magnetic interference.
2.2 Rear panel I/O connectors At the rear panel of the SB9015T is a row of external I/O device connectors detailed as follows: System with D525 CPU System with i3 CPU DC in DC in HDD slot HDD slot DC out (for 2nd LCD)
2.4 Control Panel Brightness – Press the “Brightness –” button to decrease brightness. The setting will be saved 6 seconds after releasing the button. Brightness + Press the “Brightness +” button to increase brightness. The setting will be saved 6 seconds after releasing the button.
4 Setup and Driver Installation 4.1 Cash Drawer Port Pin-out System with D525 System with i3 CPU Ground Ground Drive output Drive output 1 Sense input Sense input +24V/+12V +24V/+12V None Drive output 2 Ground Ground Operation System with D525 CPU COM port COM6 Baud rate...
4.2 Serial Ports Configurations System with D525 CPU Connectors Function Pin 9 Power Support COM1 External, RS232 (DB9) +5V/+12V select by jumper COM2 Touch controller COM3 External, RS232 (DB9) +5V/+12V select by jumper COM4 External, RS232 (DB9) +5V/+12V select by jumper COM5 External, RS232 (RJ45) +5V/+12V select by jumper...
4.4 Motherboard BIOS settings The POS terminal has a BIOS (Basic Input Output System) chip on the motherboard. Every time you start the terminals, the system will first run the BIOS self-test routine to check the main components of the system to ensure it is working properly.
Page 17
4.5 Touch screen driver installation For resistive touch versions, follow the driver installation and calibration steps below. For PCAP touch version, no driver installation/calibration is required. Step 1: Navigate to the installer directory to find the setup.exe file. Double-click on “setup.exe” to start installation. Step 2: When installation starts, click [Next] to proceed to the next step.
Page 18
Step 3: Installation in progress Step 4: Uncheck “Install PS/2 interface driver” and click [Next] to continue installation.
Page 19
Step 5: Check “install RS232 interface driver” and click [Next] to continue installation. Step 6: Select option “NONE”, click [Next] to continue installation.
Page 20
Step 7: When installing external USB touch monitor, please connect the USB controller and USB cable Step 8: If there are additional touch monitors connected, please check “Support multi- monitor system”.
Page 21
Step 9: Select the destination location to install the touch driver. The default path is “C: \ Program Files \ eGalaxtouch”. Click [Next] to continue installation. Step 10: Select the Program Folder to install the utility. The default is “eGalaxtouch”. Click [Next] to continue installation.
Page 22
Step 11: Check the option to create a desktop shortcut icon and click [Next] to finish the installation. Touch function settings Invoke the Touch Utility software to set operation options and calibrate the touch monitor.
Page 23
Touch calibration Touch device line test...
5 Troubleshooting 1) Terminal does not boot If the terminal cannot boot after repeated pressing of the power switch when connect to the power, the terminal power light remains off, the fan does not operate, and the BIOS beeping is not heard, it might be power supply problems. (a) Check the power adapter is plugged in correctly to the power outlet.
Page 25
3) The touch screen does not respond (a) Remove the touch driver and then install it again. (b) Execute the “eGalaxTouch utility and check if the interface port is working. 4) When touching the screen, cursor always returns to a fixed position. (a) Check if there is anything pressing on the touch screen.
Page 26
(a) This situation usually occurs first time after installing the driver. Please run the touch screen calibration program. We also recommend you to do this after changing monitor resolution. (b) Run the touch screen calibration program to do a 25-point recalibration.