Advertisement
Quick Links
6
Fig. A
IF AN EQUALIZER WILL BE INCLUDED: Slide the aftermarket equalizer into the back of the
kit. Using the hardware included with the equalizer, mount the unit to the kit. (see Fig. A)
IF AN EQUALIZER WILL NOT BE INCLUDED: Snap the Equalizer Dummy Plate into the
opening in the kit. (see Fig. B)
7
A
B
C
D
A) Strip wire ends back ½"
B) Twist ends together
C) Solder
D) Tape
Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adaptor and making
connections as shown. (Isolate and
individually tape off the ends of any
unused wires to prevent electrical short
circuit).
15
Fig. B
8
Re-connect the battery terminal and test the unit
for proper operation. Mount the head unit/kit
assembly to the sub-dash with those screws
previously removed in step #1.
rev. 201202
KIT COMPONENTS
Shaft
Masks
99-7400
Radio
Housing #1
INSTALLATION
INSTRUCTIONS
Radio
Housing #2
Faceplate #1
APPLICATIONS
CAR
Faceplate #2
NISSAN
200SX 1980-83.............................................................................1
Bracket Set #9
200SX 1984-88.............................................................................2
Bracket
240SX 1989-94.............................................................................3
Set #17
Axxess 1989-90............................................................................ 4
Hardbody Pickup 1986.5-93.......................................................... 5
Maxima 1982-84.......................................................................... 6
Maxima 1987-88.......................................................................... 7
Bracket Set #12
Maxima 1989-91.......................................................................... 8
Bracket #13
Pathfinder 1987-93.......................................................................5
& #14
Pulsar 1983-86............................................................................. 9
Pulsar 1987-90............................................................................. 10
Mounting
Sentra 1982-86.............................................................................9
Tabs #8
Sentra 1987-90.............................................................................11
Mounting
Mounting
Stanza 1982-86.............................................................................12
Tabs #6
Tabs #16
Stanza 1987-89.............................................................................13
Mounting
Mounting
Tabs #18
Tabs #3
Mounting
Mounting
Tabs #5
Tabs #7
Mounting
Equalizer
Tabs #1
Dummy Plate
TOOLS REQUIRED
Phillips screwdriver
1-800-221-0932
© COPYRIGHT 2001 METRA ELECTRONICS CORPORATION
Cutting tool
INST 7400
PAGE
www.metraonline.com
Advertisement
Related Manuals for Metra Electronics 99-7400
Summary of Contents for Metra Electronics 99-7400
- Page 1 Axxess 1989-90... 4 Hardbody Pickup 1986.5-93... 5 Maxima 1982-84... 6 Maxima 1987-88... 7 Maxima 1989-91... 8 Pathfinder 1987-93...5 Pulsar 1983-86... 9 Pulsar 1987-90... 10 Sentra 1982-86...9 Sentra 1987-90...11 Stanza 1982-86...12 Stanza 1987-89...13 1-800-221-0932 www.metraonline.com © COPYRIGHT 2001 METRA ELECTRONICS CORPORATION PAGE...
- Page 2 NISSAN 200SX 1980-83 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (4) Phillips screws above the radio opening. Using the scored lines as a guide, cut and Remove (1) Phillips screw below the left side of the radio opening.
- Page 3 NISSAN Stanza 1987-89 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the ashtray and (2) screws exposed at the Using the scored lines as a guide, cut and base of the dash trim bezel. Remove (2) remove the dashed portions of Faceplate screws above the climate controls and unclip the bezel.
- Page 4 NISSAN 240SX 1989-94 Disconnect the negative battery terminal to Using the scored lines as a guide, cut and prevent an accidental short circuit. Unclip remove the dashed portions of Faceplate the dash trim bezel and remove. Remove (4) Phillips screws securing the factory head unit and disconnect the wiring.
- Page 5 NISSAN Sentra 1987-90 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the ashtray. Remove (2) screws above the Locate Faceplate #2. (It is NOT necessary climate controls. Remove (2) screws from the base of the dash trim bezel and remove to cut the Faceplate).
- Page 6 NISSAN Hardbody Pickup / Pathfinder 1986 1/2- Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the ashtray and (1) screw exposed in the Using the scored lines as a guide, cut and top-right corner. Remove (2) Phillips screws above the climate controls.
- Page 7 NISSAN Pulsar 1983-86 / Sentra 1982-86 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (2) Phillips screws from the top of the dash trim Using the scored lines as a guide, cut bezel. Remove the ashtray and (1) screw exposed on the ashtray bracket.
- Page 8 NISSAN Maxima 1987-88 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (2) Phillips screws from the bottom of the Using the scored lines as a guide, cut and dash trim bezel. Remove (2) Phillips screws above the radio opening. Unclip the dash remove the dashed portions of Faceplate trim bezel and disconnect the defroster and rear wiper wiring.