AOpen FM56-ITU/2 Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

AOpen Fax/Modem Series

Thank you for choosing AOpen Fax/Modem. This file will guide you for

installation and AT commands.

AOpen FM56-ITU/2 Manual

AOpen FM56-ITU/2 AT Commands

Table of Contents

Summary of Contents for AOpen FM56-ITU/2

Page 1 AOpen Fax/Modem Series Thank you for choosing AOpen Fax/Modem. This file will guide you for installation and AT commands. AOpen FM56-ITU/2 Manual AOpen FM56-ITU/2 AT Commands...
Page 2: Table Of Contents
FM56-ITU/2 Manual Published in 2000 All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written consent of the manufacturer.
Page 3 4.10 Tips On Configur ing Your Communication Softwar e 4.11 Tips On Configur ing SVD 5 Executing Commands 6 S-Register s 7 Response Sets 8 Specifications Appendix A: FCC Compliance A.1 FCC Notice A.2 FCC Requir ement Appendix B: Default Pr ofiles...
Page 4 FM56-ITU/2 AT Commands Table of Contents 1 Hayes Compatible AT Command Set 2 ECC Command Set 3 List Of Class 1 Fax Commands 4 List Of Class 2 Fax Commands 5 List Of Voice Commands (Voice Models Only)
Page 5: Introduction
1 Introduction Congratulations on purchasing a state-of-the-art fax/modem! Your Fax/Modem incorporates the latest technological advancement for you to electronically communicate with other computers, information networks, fax machines or other fax/modems. It embraces most of the industry and commercially popular standards to ensure compatibility with most equipment and application programs.
Page 6: Feature
2 Feature • Line rate of 56 Kbps for download (FM56 series model only) • ITU-T V.90 specifications for operation at speed of 56,000 bps. • MNP10 dynamic data rate fallback and forward on the run. • Software controlled speaker volume. •...
Page 7: Pc Card Connection
3.1 PC Card Connection FM56-ITU/2 J P13 : Sound Inter face Pin Define (Optional) For connecting to AOpen Audio Car d. J P18 : Ring Wake Up Inter face Pin Define (Optional) For connecting to AOpen Mother Boar d. COM Port Setting...
Page 8: Pc Card Bracket Connection
3.2 PC Card Bracket Connection...
Page 9: Checking Your Components
4.1 Checking Your Components Unpack your fax/modem and make sure you have the following items: • The fax/modem. • A modular telephone cable to connect your fax/modem to the telephone line. • Communication software. • Two cables link JP13 and JP18 to sound card and mother board When you open your package, make sure all of the above items are included and not damaged.
Page 10: What Else You Need
4.2 What Else You Need To complete your data communication system, you will need the following items: Other communication software, if needed. An active telephone line and telephone set (if you need to use a telephone with your modem). An available ISA card slot in the personal computer. For voice function, a microphone and a speaker for voice recording and playing (voice function can also be performed by handset of telephone set connected to fax/modem).
Page 11: Installing The Pc Card Fax/Modem
4.3 Installing The PC Card Fax/Modem The following instructions explain how to install the fax/modem into a PC computer. If you will be installing the fax/modem into a different computer, refer to the manual that came with your computer or contact your computer dealer for instructions.
Page 12 7. Connect the sound card cable with JP13 and the sound card.(Optional) 8. Connect the wake up ring cable with JP18 and the mother board.(Optional) 9. Use the screw that was holding the slot cover to secure the fax/modem in the slot.
Page 13: Connecting To The Telephone Line
4.4 Connecting To The Telephone Line Use the following procedure to connect your fax/modem to the telephone line: 1. Locate an available RJ-11 modular jack telephone outlet. 2. Take one end of the modular cord supplied with the fax/modem and plug it into the LINE modular jack on the back of the fax/modem.
Page 14: Connecting To You Telephone Set
4.5 Connecting To You Telephone Set Your fax/modem also conveniently provides a second modular jack that lets you connect your telephone to the same telephone line that the fax/modem is using. This lets you manually dial data calls or make voice calls when you are not using your fax/modem.
Page 15: Verifying Your Connection
4.6 Verifying Your Connection Start a communication program and place the computer into terminal mode. Refer to your computer manual to find out the appropriate command to do so. Then use the following procedure to verify your installation: 1. Type AT[Enter ] If your system is operating properly, your fax/modem sends an OK response to your screen and waits for your next command.
Page 16: Connecting Microphone And Speaker
4.7 Connecting Microphone And Speaker You could either use a handset connected to the fax/modem, or connect a microphone and a speaker for voice recording and playback, or connect cable of Jumper 13 with sound card in your PC (optional, refer to sound card user's guide).
Page 17: Voice Function Alternatives
4.8 Voice Function Alternatives 1. AOpen Sound Card (recommanded) Simply connect the cable from modem to AOpen Sound Card. User can get all the voice function including message playing and recording through sound cards. 2. Telephone Handset If there is a telephone set connected to modem. User can get all the voice function including message playing and recording through telephone handset.
Page 18: Configuring Internal Modem With Windows3.1/95/98/2000/Nt
4.9 Configuring Internal Modem With Windows3.1/95/98/2000/NT Windows 3.1: 1. From the Main group choose Contr ol Panel icon. 2. Double click on Por ts. 3. Double click on the COM port that the modem is using. 4. Click on Advanced button. 5.
Page 19 Windows 2000: 1. Go to Contr ol Panel. Click System. Choose Har dwar e, and Device Manager , then Por ts. 2. If the COM port that the modem is using is not listed, and enter the correct Base I/O Port address and Interrupt Request Line. Set the base I/O address according to the following table: COM Port Base I/O Address...
Page 20: Tips On Configuring Your Communication Software
4.10 Tips On Configuring Your Communication Software Your fax/modem uses the most up-to-date industry and commercially popular standards to ensure functional compatibility with most communication software. During initial set-up of the communication software, it will normally prompt you to define the type of fax/modem you are using. Following is a general guideline to the device type you should choose.
Page 21: Tips On Configuring Svd
4.11 Tips on Configuring SVD Add "-SMS=2" to the modem string in communication programs to enable the SVD function. For complete SVD commands, please refer to the AT command file on the driver disk.
Page 22: Executing Commands
5 Executing Commands If you will be using a communication software program to make data calls, you will probably not need to type commands, because your software program will handle these tasks for you. Similarly, you will probably not see the responses because your software program may intercept them.
Page 23 the [Enter] key. NOTE: The fax/modem command and r esponse set ar e descr ibed in the text file, AT_CMD.TXT, in the fax/modem Windows95 dr iver diskette. You can use DOS EDIT or any suitable editor to view this file. If a command requires a parameter such as 0 and 1, the parameter is identified as n in the left column and described in the right column of the AT_CMD.TXT file.
Page 24: Registers
6 S-Registers Your fax/modem has S-registers that affect various operating characteristics. The registers let you obtain information about the fax/modem, and let you test the fax/modem. Each S-Register has a factory-set value, which you can read or change to fit your particular requirements. A complete list of S-Register is provided in the COMMAND.TXT file on the driver diskette.
Page 25 6.1 Reading An S-Register Value 1. To read the current value of an S-Register, type: ATSr ?[Enter ] where r is an S-Register number. The fax/modem responds with decimal value of the S-Register, in three-digit format, followed by OK. 2. To read values from more than one S-Register, type: ATSr ?Sr ?[Enter ] where r specify the different S-Register numbers.
Page 26 6.2 changing An S-Register Value To change an S-Register value, type ATSr =n[Enter ] where r is the S-register number. n is the value you want to assign to that S-register.
Page 27: Response Sets
7 Response Sets When you send a command to your fax/modem, it sends a response to your computer. For example, if you type AT[Enter ], the fax/modem should respond with OK. The fax/modem gives out different responses for the different tasks that it performs. Communication software use these responses to control the flow of the program.
Page 28 CONNECT 600 CONNECT 2400 CONNECT 4800 CONNECT 9600 CONNECT 7200 CONNECT 12000 CONNECT 14400 CONNECT 19200 CONNECT 38400 CONNECT 57600 CONNECT 115200 CONNECT 230400 CONNECT 75TX / 1200RX CONNECT 1200TX / 75RX DELAYED BLACKLISTED DATA CARRIER 300 CARRIER 1200/75 CARRIER 75/1200 CARRIER 1200 CARRIER 2400 CARRIER 4800...
Page 29 PROTOCOL: ALT PROTOCOL: ALT-CELLULAR 81 CONNECT 33600 CONNECT 31200 CARRIER 32000 CARRIER 34000 CARRIER 36000 CARRIER 38000 CARRIER 40000 CARRIER 42000 CARRIER 44000 CARRIER 46000 CARRIER 48000 CARRIER 50000 CARRIER 52000 CARRIER 54000 CARRIER 56000 CONNECT 32000 CONNECT 34000 CONNECT 36000 CONNECT 38000 CONNECT 40000 CONNECT 42000...
Page 30 Extended responses is disabled. With W0, all CONNECT responses reports the DTE speed. The modem will send CARRIER and PROTOCOL responses. The CONNECT response shows the DTE speed. The modem will send CARRIER and PROTOCOL responses. The CONNECT response shows the DCE speed rather than the DTE speed.
Page 31: Specifications
8 Specifications MODEM OPERATION Line Rate 0.3, 1.2, 2.4, 4.8, 7.2, 9.6, 12, 14.4, 16.8, 19.2, 21.6, 24, 26.4, 28.8, 31.2, 33.6, 56 Kbps (for 56K model only) DTE Rate 115200 bps maximum Oper ation Half or full-duplex over 2-wire dial-up line, asynchronous Linking Auto dial/answer, auto bauding, MNP10...
Page 32: Fcc Notice
A.1 FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 33: Fcc Requirement
A.2 FCC Requirement This equipment complies with Part 68 of the FCC Rules. On the base unit of this equipment is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. If requested, this information must be given to telephone company.
Page 34: Appendix B: Default Profiles
Appendix B: Default Profiles SETTING DEFAULT NVRAM Auto-answer Disabled Backspace character Bell / CCITT compatibility at Bell 212A 1200 bps Busy signal detect Enabled Carriage return character Line feed character Data Set Ready option Always on Data Terminal Ready option &D2 Data Terminal Ready pulse width 0.5 seconds Echo option...
Page 35: Hayes Compatible At Command Set
1. Hayes Compatible AT Command Set COMMAND DESCRIPTION Escape to command mode Upon on-line mode, it will remain the connection and switch the modem to command mode. The character of "Escape command" is defined by S-Register "S2". Answer command The modem will go off-hook and attempt to answer incoming call. Repeat last command ATBn Select CCITT or BELL Mode, where n = 0 or 1...
Page 36 currentlyon-line, and will terminate any test (AT&T) that is in progress. Country specific, modulation specific, and error correction protocol specific(S38) processing is handled outside of the H0 command. ATH1 If on-hook, the modem will go off-hook and enter command mode. For US models, the modem will remain off-hook. For W-class models, the modem will return on-hook after a period of time determined by S7.
Page 37 command). The parameter value, if valid, is written to S31 bit1. ATN0 Automode detection is disabled(equivalent to setting the <automode>subparameter to 0). A subsequent handshake will be conducted according to the contents of S37 or, if S37 is zero , according to the most recently sensed DTE speed. ATN1 Automode detection is enabled (equivalent to setting the +MS <automode>...
Page 38 ATSn Read/Write S-Register The modem selects an S-Register, performs an S-Register read or write function, or reports the value of an S-Register. Establishes S-Register n as the last register accessed. Sn=v Sets S-Register n to the value v. Sn=? Repotrs the value of S-Register n. The parameter n can be omitted, in which case the last S-Register accessed will be assumed.
Page 39 is written to S31 bits 2 and 3. Note that the Wn command can be overridden by register S95 bits(see S95 description). ATW0 Upon connection, the modem reports only the DTE speed(e.g.,CONNECT 57600). Subsequent responses are disabled.(Default) ATW1 Upon connection, the modem reports the line speed, the error correction protocol, and the DTE speed, respectively.
Page 40 ATX3 Enables monitoring of busy tones; send only OK,CONNECT,RING, NO CARRIER,ERROR,NO ANSWER, and CONNECT XXXX. Blind dialing is enabled/disabled by country parameters. If dial tone detection is enforced and dial tone is not detected. NO CARRIER will be reported. The value 110b is written to S22 bits 6, 5, and 4, respectively. ATX4 Enables monitoring of busy tones;...
Page 41 AT&D1 DTR drop is interpreted according to the current & Qn setting as follows: &Q0,&Q1,&Q4,&Q5,&Q6 DTR drop is interpreted by the modem as if the asynchronous escape sequence had been entered. The modem returns to asynchronous command state without disconnecting. &Q2,&Q3 DTR drop causes the modem to hang up.
Page 42 AT&Mn Asynchronous/Synchronous Mode Selection (External Models Only) AT&M0 Selects direct asynchronous operation. Note that the command sequence &M0\N0 selects normal buffered mode, but the command sequence \N0&M0 selects direct mode. This is because the \N0 command is analogous to the &Q6 command. The value 000b is written to S27 bits 3,1,and 0, respectively.(See &Q).
Page 43 AT&Q4 Selects AutoSync operation.The value 100b is written to S27 bits 3, 1, and 0, respectively AutoSync operation, when used in conjunction with the Hayes Synchronous Interface (HSI) capability in the DTE, provides synchronous communication capability from an asynchronous terminal. Starting AutoSync.
Page 44 To terminate a test in progress, the escape sequence must be entered first, except for parameters 7 and 8. If S18 is non-zero, a test will terminate automatically after the time specified by S18 and display the Ok message. AT&T0 Terminates test in progress.Clears S16.
Page 45 REQUEST LAST TX data rate... 33600 BPS HIGHEST TX data rate..33600 BPS LAST RX data rate... 28800 BPS HIGHEST RX data rate..28800 BPS Error correction PROTOCOL... LAPM Data COMPRESSION.... V42Bis Line QUALITY....030 Highest SPX RX state..068 Highest SPX TX state..
Page 46 Serial Number Sets and stores eight serial numbers in hex format used for serial Plug and Play and for ISA Plug and Play which use the Rockwell 11575 Plug and Play device. Example: AT%7<8 hex numbers><same 8 hex numbers> AT%8 Plug and Play Vendor ID and Product Number Sets and stores Vendor ID and product number for serial Plug and Play and for ISA Plug and...
Page 47 AT\K5 Send break to remote modem in sequence with transmitted data. (Default) The second case is where the modem is in the on-line command statewaiting for AT commands during a data connection, and the \B is received in order to send a break to the remote modem: AT\K0 Clear data buffers and send break to remote modem.
Page 48 MNP error-correction connection results in the modem hanging up. (Forces &Q5, S36=4, and S48=128) AT\Vn Single Line Connect Message Enable The single line connect message format can be enabled or disabled by the \Vn command as follows: AT\V0 Connect messages are controlled by the command settings X, W, and S95.
Page 49 This extended-format command selects the modulation and, optionally, enables or disables automode, specifies the lowest and highest connection rates, selects m-Law or A-Law codes type, and enables or disables robbed bit signaling generation (server modem) or detection (client modem) using one to five subparameters.
Page 50 (0,1,2,3,9,10,11,64,69),(0,1),(300-33600),(300-33600),(0,1),(0,1) [RC336] AT+MS: (0,1,2,3,9,10,64,69),(0,1),(300-14400),(300-14400),(0,1),(0,1) [RC144] Subparameter Definitions 1. <mod> = A decimal number which specifies the preferred modulation (automode enabled) or the modulation (automode disabled) to use in originating or answering a connection. The options are: <mod> Modulation Possible Rates (bps) 1 Notes V.21 V.22...
Page 51 b. The DTE may disable automode operation (see <automode> below). c. The DTE may constrain the range of modulations available by specifying the lowest and highest rates (see<min_rate> and <max_rate> below). 2. <automode> is an optional numeric value which enables or disables automatic modulation negotiation using V.8 bis/V.8 or V.32 bis Annex A.
Page 52 b. To emulate issuance of the N1S37=x sequence command, specify the modulation and the rate to start automoding down from using <mod> and <max_rate>, respectively. Set <min_rate> to 300 to allow automoding all the way down to V.21 300 bps. For example: AT+MS=11,1,300,16800 selects automode starting at V.34 16800 bps (no comparable S37 command).
Page 53: Ecc Command Set
2. ECC Command Set COMMAND DESCRIPTION AT%Cn Enable/Disable Data Compression Enables or disables data compression negotiation.The modem can only perform data decompression on an error corrected link. The parameter value, if valid, is written to S41 bits 0 and 1. AT%C0 Disables data decompression.Resets S46 bit 1.
Page 54 AT*Hn Link Negotiation Speed This command is included only for compatibility and performs no function. *H0 *H0 command. *H1 *H1 command. *H2 *H2 command. AT-Kn MNP Extend Services Enables or disables conversion of a V.42 LAPM connection to an MNP 10 connection.
Page 55: List Of Class 1 Fax Commands
3. List Of Class 1 Fax Commands COMMAND DESCRIPTION AT+FCLASS=n Select Service Class AT+F<command>? Report Active Configuration AT+F<command>=? Report Operating Capabilities AT+FAE=? 0 if autoansweris disabled; 1 if auto answer is enabled AT+FRH=n Receive Data with HDLC Framing AT+FRM=n Receive Data AT+FFRMn Receive silence AT+FTH=n...
Page 56: List Of Class 2 Fax Commands
4. List Of Class 2 Fax Commands COMMAND DESCRIPTION AT+FCLASS=n Select Service Class. Same as class 1. AT+FDT Data Transmission AT+FET=n Transmit Page Punctuation AT+FDR Begin or Continue Phase C Receive Data AT+FK Session termination AT+FCON Facsimile connection response AT+FDCS: Report current session AT+FDIS: Report remote identification...
Page 57: List Of Voice Commands (Voice Models Only)
5. List Of Voice Commands (Voice Models Only) COMMAND DESCRIPTION AT#BDR Select Baud Rate(Turn off Autobaud) This command forces the modem to select a specific DTE/modem baud rate without further speed sensing on the interface. When a valid #BDR=n command is entered, the OK result code is sent at the current assumed speed. After the OK has been sent, the modem switches to the speed indicated by the #BDR=n command it has just received.
Page 58 #CLS=0 Data. This is similar to setting +FCLASS=0,and instructs the modem to act like a data modem on subsequent answer or originate operations. When a disconnect or inactivity time out in the non-autobaud mode is detected, the modem automatically sets the #CLS setting to 0 and hangs up. This ensures that the modem is always in a known state despite disorderly DTE behavior.
Page 59 sample) Default: Result Codes: If n=2,3,or 4 ERROR Otherwise. Command options: #VBS? Returns the current setting of the #VBS command as an ASCII decimal value in result code format.rates are correlated with the #VCI? query command response which provides the single compression method available.
Page 60 Parameters: n=0,1,2,3,or 4 [This is the device position number(not device number) as reflected in response to #VLS=?] Default: Result Codes: If n=0,1,2,3,or 4 VCON If device selected does not connect to the telephone line. (A speaker is such a device, but a telephone line with speaker ON is not such a device, and generates OK.) ERROR If n does not equal 0,1,2,3,or 4,or if already off-hook.
Page 61 AT#VRA Ringback Goes Away Timer(Originate) This command can be used, when originating a voice call(#CLS=8)to set the "Ringback Goes Away" timer value,i.e.,an amount of time (in units of 100ms) measured from when the ringback cadence stops once detected. If ringback is not detected within this period, the modem assumes that the remote has picked up the line and switches to Online Voice Command Mode.
Page 62 be received from the line, microphone, or handset. The #VLS command should have been previously issued to select the input source. Parameters: None Result Codes: CONNECT When voice transfer from modem to DTE can begin. ERROR If #VLS=0 and not connected to any input device.