LG 47LB1DA Owner's Manual page 116

APPENDIX
Data5:
Main/Sub
7
Picture
0 Main
1 Sub
All data are transmitted by Hexadecimal code
* Two/One part Channel: 6th bit
This bit is used in a cable-ready system.
* Using physical channel: 5th bit
If the channel band is NTSC air or NTSC cable, channel
tuning can be done by only physical channel. In this
case, using physical channel bit must be low(0).
But if the channel band is ATSC air or ATSC cable, there
are two cases that physical channel enable or disable.
If the physical channel sending is meaningful, you should
set this bit low(0). If the physical channel sending is
meaningless, you should set this bit high(1).
Example)
1. Analog channel: NTSC cable, channel number(35),
main picture Command: ma 00 23 xx xx xx xx 01
attribute(0x01): main picture, two part(it's not
mandatory), using physical channel, NTSC cable 'xx'
data: don't care major and minor channel number in
case analog channel tuning.
2. Digital channel: ATSC air, channel number(don't know
physical channel, major(30), minor(3)), sub picture
Command: ma 00 xx 00 1E 00 03 A2
attribute(0xA2): sub picture, two part, not using
physical channel, ATSC air 'xx' data: don't care analog
channel number in case digital channel tuning.
3. Digital channel: ATSC air, channel number(physi-
cal(20),major(20), minor(3)), sub picture Command:
ma 00 14 00 14 00 03 82
attribute(0x82): sub picture, two part, using physical
channel, ATSC air.
Acknowledgement[a][ ][Set ID][ ][OK][Data0][Data1]
[Data2][Data3][Data4][x][a][ ][Set ID]
[ ][NG][Data0][x]
2 2 5 5 . . C C h h a a n n n n e e l l A A d d d d / / D D e e l l ( ( C C o o m m m m a a n n d d : : m m b b ) )
To add and delete the channels
114
Two/One
Part Channel
Two/One Using Physical
6 5
Part Channel
Channel
0 Two 0 Use
1 One 1 No Use
4 3 2
Reserved
x 0 0
x 0 0
x 0 0
x 0 0
x 0 1
x 0 1
x 0 1
x 1 1
x x x
x 1 1
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 0: Channel Delete
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
2 2 6 6 . . K K e e y y ( ( C C o o m m m m a a n n d d : : m m c c ) )
To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]s
Data Key code: Refer to page 1 16.
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
2 2 7 7 . . I I n n p p u u t t s s e e l l e e c c t t ( ( C C o o m m m m a a n n d d : : x x b b ) ) ( ( M M a a i i n n P P i i c c t t u u r r e e I I n n p p u u t t ) )
To select input source for TV.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data 00 : DTV (Antenna)
Data 10 : Analog (Antenna)
Data 20 : AV1
Data 40 : Component 1
Data 50 : RGB DTV
Data 90 : HDMI1/DVI
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
2 2 8 8 . . P P I I P P I I n n p p u u t t S S e e l l e e c c t t ( ( C C o o m m m m a a n n d d : : x x y y ) )
To adjust input source for sub picture in PIP mode.
Transmission [x][y][ ][Set ID][ ][Data][Cr]
Data 00 : DTV (Antenna)
Data 01 : DTV (Cable)
Data 10 : Analog (Antenna)
Data 1 1 : Analog (Cable)
Data 20 : AV1
Data 21 : AV2
Acknowledgement [y][ ][Set ID][ ][OK/NG][Data][x]
Step
1 0
0 0
NTSC Air
0 1
NTSC Cable
1 0
ATSC Air
1 1
ATSC Cable_std
0 0
ATSC Cable_hrc
ATSC Cable_irc
0 1
ATSC cable_auto
1 0
Reserved
1 1
-
x x
Reserved
1 1
Data 1: Channel Add
Data 01 : DTV (Cable)
Data 1 1 : Analog (Cable)
Data 21 : AV2
Data 41 : Component 2
Data 60 : RGB PC
Data 91 : HDMI2