Advertisement
Operation Guide 3440 3441
To position the lap time and split time on the display
Each press of A cycles the lap time and split time positions in the sequence shown
below.
•
You can perform the above operation while stopwatch operation is ongoing or
stopped.
Remaining memory
Lap time
Split time
Lap time
Split time
E-20
Recall Mode
Creation date
Use the Recall Mode to recall and delete records stored
(Month – Day)
by the Stopwatch Mode.
•
Stopwatch records are stored in "logs" that are created
automatically by the watch. See "Memory Management"
on page E-48 for more information.
•
The title screen of the newest log appears fi rst
whenever you enter the Recall Mode.
•
Log numbers are automatically assigned in sequence,
starting from
•
All of the operations in this section are performed in the
Recall Mode, which you enter by pressing C (page E-9).
Log number
To recall stopwatch records
Time measurement
In the Recall Mode, use A to scroll through the log title
was performed
screens, starting from the newest one, as shown below.
Log Title Screen
When the title screen of the log you want is displayed, use
D (+) and B (–) to cycle through the records contained
in the log.
E-22
•
The locations of the lap time and split time in the Stopwatch Record screen are
determined by the display format you last selected in the Stopwatch Mode (page
E-17).
•
The BEST indicator identifi es the record that contains the best lap time in the log.
•
If a best lap time record is deleted automatically when the log becomes full, the
BEST indicator will not be transferred to the record with the next best lap time. See
"Memory Management" on page E-48 for more information about automatic deletion
of records.
To delete a log
1. In the Recall Mode, display the title screen or one of the records of the log you want
to delete.
2. While holding down B, hold down D for about two seconds until the watch beeps.
•
"CLR" will fl ash on the display for two seconds and then the watch will beep.
Release B and D at this time.
•
You cannot delete the log of an ongoing elapsed time measurement operation.
E-24
Countdown Timer
Number of Repeats
Dual timers can be set with two different starting times.
The watch can be confi gured so the two timers alternate,
so when one reaches the end of its countdown, the other
timer starts. You can specify a "number of repeats" value,
which controls how many times the two-timer countdown
operation is performed (1 = once, 2 = twice, etc.). The
starting time of each timer can be set in fi ve-second steps
up to 99 minutes, 55 seconds.
You can specify up to 10 repeats. The watch emits a short
Seconds
beep whenever either of the timers reaches the end of its
countdown during an ongoing timer operation. The watch
Minutes
Timer 1
emits a 5-second beep when the end of the fi nal timer
operation (specifi ed by the number of repeats) is reached.
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero. The
beeper stops after about 5 seconds or when you press any button.
E-26
3. When the setting you want to change is fl ashing, use D and B to change it as
described below.
Setting
Screen
Minutes, Seconds
Number of Repeats
•
To disable either timer, set 00'00" as its countdown start time.
4. Press A to exit the setting screen.
E-28
Lap time
Split time
Hours
Seconds
Hours
Seconds
Minutes
Minutes
.
Button Operation
Use D (+) and B (–) to change the setting.
Use D (+) and B (–) to change the setting.
More than 10 hours
•
Whenever the elapsed time exceeds 10 hours, the measurement changes from
1/100-second units to 1-second units.
Stopwatch Record
Lap/Split number
Log Title Screen
To delete all logs
While holding down B, hold down D for about fi ve seconds until the watch beeps
once and then a second time.
•
"CLR" will fl ash on the display for two seconds and then the watch will beep once.
Keep B and D depressed and "ALL" will fl ash on the display for three seconds,
and then the watch will beep again. This indicates that all log data is cleared.
•
You cannot delete logs while an elapsed timing operation is in progress.
To confi gure the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to fl ash, which indicates the
setting screen.
•
If the countdown start time is not displayed, use
the procedure under "To use the countdown timer"
(page E-29) to display it.
2. Press C to move the fl ashing in the sequence shown
below to select other settings.
Timer 1
Minutes
To use the countdown timer
Current repeat count
Current timer time
Current time
(Start/Stop)
Press D while in the Countdown Timer Mode to start the countdown timer.
•
The countdown is performed by alternating between Timer 1 and Timer 2. A short
beep is emitted to signal a changeover from one timer to the other.
Press D to pause a countdown. Press D again to resume.
•
Pressing B while a countdown timer is stopped resets it to the start time specifi ed
•
by you.
•
The watch emits a 5-second beep when the end of the fi nal timer operation
(specifi ed by the number of repeats) is reached.
•
Even if you exit the Countdown Timer Mode, the countdown timer operation
continues and the watch beeps as required.
E-21
Best Lap Time
Screen
Screen
BEST indicator
Lap time
Split time
E-23
E-25
Timer 1
Timer 2
Timer 2
Seconds
Minutes
Seconds
Number of Repeats
E-27
Preset number of repeats
(Reset)
Timer 1 or 2
E-29
Advertisement
