Table of Contents
Advertisement
Viewing 3D images on TV
You can enjoy 3D images by wearing the 3D Eyewear supplied with this TV and to view 3D broadcasts and 3D image software.
Basic features of 3D Eyewear
This product cannot be used as sunglasses.
This product can be worn over vision correction glasses.
Optional Accessory
TY-EW3D10U (as of April, 2010)
Visit http://www.panasonic.com/ for more information.
Part names and functions
Infra-red receiver
Receives infra-red signals from the television.
The liquid crystal shutter open/close timing is controlled by receiving infra-red
signals from the television, which provide 3D expression of the images.
Battery case
Nose pad installation section
Fitting the batteries (p. 23)
3D Eyewear inner section (p. 23)
When using for the first time,
remove the insulating sheet.
(p. 23)
Liquid Crystal
Power button
Shutter
(bottom side of 3D Eyewear)
Controls the images for
Switches on the 3D Eyewear power.
3D viewing.
The left and right liquid
Power button
crystal shutters are
alternately opened
and closed in time with
Press and hold the power button for approximately
the left side and right
side images that are
1 second to switch the power on, and the Indicator
lamp lights for approximately 2 seconds. To switch
alternately displayed
the power off, press and hold the power button for
on the television to
approximately 1 second. (The Indicator lamp flashes 3
achieve the 3D effect.
times, then the power switches off.)
Specifications
Lens type
Liquid Crystal Shutter type
Coin-shaped lithium battery CR2032
Batteries
(duration)
(approx. 75 hours in continuous use)
32 °F – 104 °F
Usage temperature
range
(0 °C – 40 °C)
Transmitter for 3D Eyewear
Viewing range*
Within 3.2m from front surface
(Within ±35° horizontal, ±20° vertical)
22
Accessories
3D Eyewear (1)
3D Eyewear case (1)
Specialized band can be
Specialized band (1)
attached here. (p. 23)
If the end of the specialized
band is loosened, make a loop
at the end as shown in the
above figure and smooth the
twisted rubber before using.
Nose pad (1 of each)
A
Use either nose pad A or B
Indicator lamp
for your preference.
If you put the 3D Eyewear
on vision correction
glasses, the nose pad
is recommended to be
removed.
Width: 6.97" (177 mm)
Dimensions
Height: 1.82" (46 mm)
Overall length: 6.86" (174 mm)
Power supply
DC 3 V
Mass (including batteries)
0.14 lb (63 g)
Main body: resin
Materials
Lens section: Liquid crystal glass
* Viewing range: The location of the 3D Eyewear transmitter (p.13)
Remove the insulating sheet
Attach the specialized band
If the 3D Eyewear slips out of place, use the specialized band included to hold it in place.
Specialized band
Attach the nose pad
Nose pad A
B
When the remaining battery level is low, the Indicator lamp flashes 5 times upon turning the 3D Eyewear power ON.
(Early battery replacement is recommended.)
Loosen the screw from the cover using the
screwdriver (included).
Replace the battery, and then replace the
cover.
Using for the first time
insulating sheet
Attach the band to the left and right tips of the frame, and adjust the
length.
If required, use the included nose pad.
Nose pad A adjusts the attachment position of the 3D Eyewear between 2
vertical levels.
(Slot 2 of the 3 protrusions on the 3D Eyewear deeply into the holes on nose
pad A.)
When using nose pad B, ensure that all 3 protrusions on the 3D Eyewear are
inserted deeply into the 3 holes on nose pad B.
Replacing the batteries
Note
Use the specified type of battery (coin-shaped lithium
battery CR2032).
screwdriver
Do not insert the battery with the polarity (plus
minus
) backwards.
Dispose of the old batteries as non-burnable garbage, or
in line with the garbage regulations in your local area.
Always tighten the screw to hold the battery case cover
in place.
and
23
Advertisement
Table of Contents
