Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for KitchenAid KCDP 9010/I
Summary of Contents for KitchenAid KCDP 9010/I
- Page 1 KCDP 9010/I Instructions for use...
-
Page 3: Table Of Contents
Warnings Safeguarding the environment Instructions for installation and use Extraction Modes Installation Hood description Functioning Maintenance After-Sales Service... -
Page 4: Warnings
Warnings • This appliance should not be used by children or people with limited physical or mental abilities and with no experience or knowledge of its use, unless they are supervised by someone in charge of their safety or who has taught them how to use the appliance. •... -
Page 5: Safeguarding The Environment
Warnings Declaration of conformity This product has been designed, manufactured and marketed according to the following: - safety objectives of the “Low Voltage” Directive 2006/95/CE (wich replaces 73/23/CEE and subsequent amendments). - protection requirements of “EMC” Directive 89/336/EEC amended by Directive 93/68/EEC. Troubleshooting guide Hood does not work: •... -
Page 6: Instructions For Installation And Use
Instructions for installation and use This is an excessively heavy product and the movement and installation of the hood should be done by at least two or more people. Follow the instructions in this manual carefully. All responsibility is denied for problems, damage or fire to the appliance resulting in failure to comply with the instructions in this manual. -
Page 7: Installation
Installation The hood comes with plugs suitable for most it with some protection where you can place walls/ceilings. You should however consult a the hood and parts. qualified technician to make sure the installation is • Disconnect the hood by turning off the mains suitable for your kind of wall/ceiling. - Page 8 Installation Fig. 4 Fig. 5 • Place the lower support bracket on the • Hang the hood on the lower bracket. perforation layout aligning it with the sketched • Adjust the distance of the hood from the wall. rectangle. Mark the two external holes, then •...
- Page 9 Installation • The hood has two identical brackets for above the lower bracket at a distance of attaching the chimney. 200mm, attach the bracket with 2 screws and Attach the first bracket (G – the side with fixing plugs. 2 rubber strips should be attached to the holes facing upwards –...
- Page 10 Installation • Hook the hood onto the lower bracket. • Attach the upper chimney and fix it to the • Fit the hood securely to the wall with screws support bracket G with 2 screws. • Connect the venting pipe (Venting pipe and Note: The upper chimney should also cover the straps are not provided and must be purchased bracket M.
-
Page 11: Hood Description
Hood description Fig. 9 1. Control panel 2. Grease filter 3. Handle for unhooking the grease filter 4. Halogen bulbs 5. Steam deflector screen 6. Telescopic chimney 7. Air outlet (only for use with filter version) 8. Perimetric suction panel Functioning Turn to maximum speed when there is a lot of steam in the kitchen. -
Page 12: Maintenance
Maintenance Always disconnect the power supply before carrying out any kind of maintenance work. Cleaning The hood should be cleaned regularly both inside and out (at least as often as you carry out maintenance on the grease filters). Use a damp cloth with mild cleaning products. Avoid using harsh products. - Page 13 Maintenance Carbon filter (only in recirculation mode) Fig. 12 The Carbon filter absorbs any unpleasant smells produced when cooking. The carbon filter can be washed every two months in hot water with suitable cleaning fluids, or in the dishwasher at 65°C (when washing in the dishwasher, do a full wash without any plates inside).
-
Page 14: After-Sales Service
After-Sales Service Before calling Customer Care Centre: 1. See if you can solve the problem yourself with the help of the “Troubleshooting guide”. 2. Switch off the hood for a few minutes and re- start it to see if the problem has cleared itself. 3. -
Page 15: Electrical Connection For Great Britain And Ireland Only
Socket outlet / plug (valid for both countries) If the fitted plug is not suitable for your socket outlet, please contact KitchenAid Service for further instruction. Please do not attempt to change plug yourself. This procedure needs to be carried out by a qualified technician in compliance with the manufactures instructions and current standard safety regulations. - Page 16 Printed in Italy 05/07 5019 718 02007...