Table of Contents
Advertisement
QQ
3 7 63 1515 0
4-6.
OPERATING THE CONTINUOUS PLAYBACK
MODE
4-6-1. Entering the Continuous Playback Mode
1. Set the MO or CD disc in the unit. (Whichever recordable discs
or discs for playback only are available.)
2. Press the = 0 button or ) + button and display
"CPLAY MODE".
3. Press the YES button to change the display to "CPLAY MID".
4. When access completes, the display changes to
"C1=
AD=
Note: The numbers " " displayed show you error rates and ADER.
4-6-2. Changing the Parts to be Played-back
1. Press the YES button during continuous playback to change
the display as below.
CPLAY MID
2. When access completes, the display changes to
"C1=
AD=
Note: The numbers " " displayed show you error rates and ADER.
4-6-3. Exitting the Continuous Playback Mode
1. Press the EDIT/NO button. The display will change to
"CPLAY MODE".
2. Press the 6 button and remove the disc.
Notes:
TE
L 13942296513
1. The playback start address for IN, MID, and OUT are as fol-
lows.
In case you want to display the address of the playback posi-
tion on the display, press the DISPLAY button and display
"CPLAY (
IN
: 40h cluster
MID : 300h cluster
OUT : 700h cluster
2. The EDIT/NO button can be used to stop playing anytime.
www
.
http://www.xiaoyu163.com
".
CPLAY OUT
CPLAY IN
".
)".
x
ao
y
i
http://www.xiaoyu163.com
8
4-7. OPERATING THE CONTINUOUS RECORDING
MODE
4-7-1. Entering the Continuous Recording Mode
1. Set the MO disc in the unit.
2. Press the = 0 button or ) + button and display
"CREC MODE".
3. Press the YES button to change the display to "CREC MID".
4. When access completes, the display changes to "CREC (
and, SHUFFLE and REPEAT Turn on.
Note: The numbers " " displayed shows you the recording posi-
tion address.
4-7-2. Changing the Parts to be Recorded
1. When the YES button is pressed access is completed, the
display changes as below. (See Note 6.)
CREC MID
2. When access completes, the display changes to "CREC (
and SHUFFLE and REPEAT lightup.
Note: The numbers " " displayed shows you the recording posi-
tion address.
4-7-3. Ending the Continuous Recording Mode
1. Press the EDIT/NO button. The display will change to "CREC
MODE" and PRESET goes off.
Q Q
2. Press the 6 button and remove the disc.
3
6 7
1 3
( MONO turns on once and turns off immedia Tely.)
Notes:
1. The recording start address for IN, MID, and OUT are as fol-
lows.
IN
: 40h cluster
MID : 300h cluster
OUT : 700h cluster
2. The EDIT/NO button can be used to stop recording anytime.
3. During the test mode, the erasing-protection tab will not be
detected. Therefore be careful not to set the continuous re-
cording mode when a disc not to be erased is set in the unit.
4. Do not perform continuous recording for long periods of time
above 5 minutes.
5. During continuous recording, be careful not to apply vibra-
tion.
6. After access is completed, the recorded portions cannot be
moved any more.
u163
.
– 11 –
2 9
9 4
2 8
CREC OUT
1 5
0 5
8
2 9
9 4
m
co
9 9
)"
CREC IN
)"
2 8
9 9
Advertisement
Table of Contents
