Page 1
1'150 Input A.C. only 50 Hz 60 Hz D.C. 7.2 V MODEL 6 3 1 2 D MODEL 6312DW With Fast Charger MODEL 6312DWG With Fast Charger Dimensions weight 2 4 7 m m x 7 9 m m x 233"...
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2.
Page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure t o use one heavy enough t o carry the current your product will draw.
Page 4
VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY t o the user as well as damage t o the tool.
Page 5
Before using battery charger, read all instructions and cautionary markings (1) battery charger, (2) battery, and CAUTION To reduce risk of injury, charge only MAKITA Battery Cartridge 1200 & 1201. Other types of batteries may burst causing personal injury and damage.
Page 6
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (SOOF) or ABOVE 4OoC (104OF). Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. Do not allow anything t o cover or clog the charger vents. Always cover the battery terminals with the battery cover when the battery cartridge is not used.
Page 7
*After charging, unplug the charger from the power source. CAUTION : *The fast charger Model DC1201 is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer’s batteries. *When you charge a new battery cartridge or...
Page 8
I f you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed t o direct sunlight or heat for a long time, the charg- ing light may flash in red color. I f this occurs, wait for the battery cartridge cools.
Page 9
Switch action Tool speed is increased by increasing pres- sure on the trigger. To s t a r t the tool, simply pull the trigger. Release the trigger to stop. CAUTION : Before inserting the battery cartridge into the tool, always check t o see that the switch trigger actuates properly and returns to the Reversing switch action This tool has a reversing switch t o change...
Page 10
Adjusting fastening torque The fastening torque can be adjusted in six stages by turning the adjusting ring so that the pointer on the adjusting ring points t o a number on the tool body. The fastening torque i s minimum when the pointer points t o the number 1 and maximum when it points to the marking.
Page 11
Drilling operation First, turn the adjusting ring so that the pointer on the adjusting ring points t o marking. Then proceed *Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a center- punch and hammer a t the point to be drilled place the point of the bit in the indenta-...
Always be sure that the tool is switched off and the battery cartridge attempting t o perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. removed before...
Page 13
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
Page 14
Sep.-08-'94 CORDLESS DRIVER DRILL Model 63120 Note: The switch and other part configurations may differ from country to country.
Page 15
MODEL 6 3 1 2 0 MACHINE Name Plate Tapping Screw BT4x20 Housing Set IWith Item 571 Pan Head Screw M4x22 IWith Washerl Sponge 1 4 - 7 2 Switch Lever Switch Lever Keyless Drill Chuck 13 Flat Head Screw M6x22 Spindle Bearing Retainer 17 Ball Bearing 6000LLB...
Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location. Call your nearest Makita Service Center or Distributor to determine the location that provides Makita battery recycling. See your local Yellow Pages under "Tools- Electric'...