Page 1
Model DC9700 Fast Charger Voltage 9 6 V only 50 Hz Equipped with Electric Brake (3/8") MODEL 60921) (318") MODEL 6 0 9 2 D W load speed IRPM) High 2 4 7 m m x 581" l , l o o...
IMPORTANT SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1 . KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2.
Page 3
DISCONNECT TOOLS. When not in use, before servicing, and when chang- accessories, such REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking see that keys and adjusting wrenches are removed from tool before turning it on. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on switch.
Page 4
Before using battery charger, read all instructions and cautionary markings on (1) battery charger, ( 2 ) battery, and ( 3 ) product using battery. CAUTION - To reduce risk of injury, charge only MAKITA Battery 7000, 9000 or 9100. Other types of batteries may burst causing personal injury and damage.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator receptacle. 3. Do not allow anything to cover or clog the charger vents. 4.
Page 6
Installing or removing battery cartridge tool Always switch off t h e before insertion or removal of the battery cartridge. *To remove the battery cartridge, pull out tool t h e plate on t h e and grasp both sides of the cartridge while withdrawing it from t h e barrel.
Page 7
When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, may not accept not indicate a problem. You can recharge the battery cartridge fully after discharging almost completely a couple of times. If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger.
Page 8
CAUTION : Before inserting the battery cartridge into the switch actuates properly and returns Reversing switch action tool This has a reversing switch the direction of rotation. Slide the revers- ing switch to the right for clockwise rota- tion o r to the left for counterclockwise. CAUTION : Always check the direction of rotation before operation.
Page 9
Drilling operation Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. To prevent the bit from slipping when starting a hole, make an indentation with a centerpunch and hammer at the point to be drilled.
Page 10
Screwdriving operation Place the point of the driver bit screw head and apply pressure to the Start the tool slowly and then increase the speed gradually. Release the trigger just as the screw bottoms out. The electric brake tool immediately, pre- will then stop the venting the screw and/or bit from being damaged.
Page 11
Hole tool, When storing the the hole in the heel the tool is a convenient way t o hang by a cord, hook other means. correct Selecting Phillips bit Use the chart determine the best size driver bit for the size of screw that use.
Page 12
Always be sure that the tool is switched off and the battery cartridge is removed before attempting perform inspection To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized Makita replacement parts. maintenance. Factory Service Centers, always using...
Page 13
These accessories o r a t t a c h m e n t s a r e recommended for use with your Makita t o o l specified in this of a n y o t h e r accessories or a t t a c h m e n t s might present a risk manual.
Page 14
Battery holster Holster holds extra b a t t e r y . No. 823033-3C Part Tool holster has s o m e bits storage space. Use holster t o carry drill only after Also, removing bit. keep t h e reversing in neutral position w h e n switch lever carrying in t h e holster.
Page 15
Aug - 0 8 10 mm (3/8”) CORDLESS DRIVER DRILL Model 6 0 9 2 D Note: The switch and other part configurations may differ from country to country.
Page 16
MODEL 6 0 9 2 0 DESCRIPTION MACHINE Drill Chuck S l O Head Screw M5x18 Spindle Ball Bearing 600CiLB Stop Ring E - 9 Compression Spring 10 Thin Washer 10 Spur Gear Ring Spur Gear 9 3 Housing Sef [With Item 271 Pan Head Screw Max22 [With Washed Switch DC Motor 3...
The tool has been abused, misused or improperly maintained; alterations have been made to the IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CON- SEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY.