Changing Setups - Panasonic WJ-HDE300 Instruction Manual

● Changing Setups
Changing the total number of HDD in
RAID5
Do the following when the total number of the hard
disks in the extension unit is increased (3 to 4) or
reduced (4 to 3) after the system has been operated.
Important:
• The MODE switches of all extension units in a system
should be set to the same position, SINGLE or RAID5.
Otherwise, the system will malfunction.
• At least three hard disk drives per extension unit are
needed to run it in the RAID5 mode.
• When the total number of the hard disks in an extension
unit is increased or reduced, all data previously stored
in the unit will be erased.
1 SAFETY MODE ON
Select ON for "HDD Safety Mode" and close the SETUP
MENU.
SETUP MENU
System Recording
Advanced
Switcher Display
1
REC Rate
160GB 160GB
MAIN
Disk Info 15000h 15000h
160GB 160GB
EXT1
Version Info 15000h 15000h
160GB 160GB
EXT2
Disk End Mode
15000h 15000h
160GB 160GB
EXT3
Disk Capacity
15000h 15000h
160GB 160GB
EXT4
Date Delete
15000h 15000h
160GB 160GB
EXT5
15000h 15000h
160GB 160GB
EXT6
Event Log
15000h 15000h
160GB 160GB
EXT7
Error Log
15000h 15000h
Access Log
■
Warning for Disk Life Time
■
Quick Menu HDD Safety Mode
→ The recorder will restart and the HDD SAFETY MODE
window will be displayed.
2 Install/uninstall the hard disk
• Confirm that the HDD POWER indicator on the front
panel of the extension unit went out.
• Install or uninstall the hard disk referring to ■
Replacing/Mounting HDD.
• Go to the next step below after finishing the con-
nection of the front cover harness with the unit while
the switches and buttons remain operable (step 11
of ■ Replacing/Mounting HDD).
Event Schedule
LIVE
Comm Maintenance
2 3 4
Remaining
Normal REC Area
1800GB
160GB 160GB Event REC Area 1200GB
15000h 15000h
Copy Area 1000GB
160GB 160GB
1 1000GB
COPY (Rear)
15000h 15000h
160GB 160GB 1000GB
COPY 2 (Front)
15000h 15000h
160GB 160GB
15000h 15000h
160GB 160GB
15000h 15000h
160GB 160GB
15000h 15000h
160GB 160GB
15000h 15000h
3000h
OFF
3 Initializing the unit
1 Set the MODE switch to SINGLE.
2 While holding down the RECOVER but-
ton, press the RESET button.
3 While holding down the RECOVER button, release
the RESET button about 1 second later.
4 Release the RECOVER button after the HDD
POWER indicator turns on (5 seconds later).
5 Repeat the above steps when initializing two or
more units.
HDD
POWER
HDD
POWER
4 Set the MODE switch back to RAID5.
5 SAFETY MODE OFF
• Select OFF on the HDD SAFETY MODE window and
press the SET button.
→ The recorder will restart and the HDD
DISK MENU will be displayed after the
system check is completed (3 - 5 min-
utes later).
HDD DISK MENU
Digital Disk Recorder
WJ-HD300A TOP MENU THE CANDIDATE FOR A FORMAT
ALL UNIT
-
MAIN
480GB
EXT1
480GB
EXT2
EXT3 480GB
*(480GB)
EXT4
ADD (480GB)
EXT5
480GB
EXT6
EXT7 LOST
RETURN: [ SETUP/ESC ] OK : [ SET ]
• Perform the formatting of the changed extension unit.
MODE
SINGLE RAID5
ERROR
RESET
MODE
SINGLE RAID5
3
HDD 2
POWER
HDD POWER
Press Release
OFF ON
OPERATE RECOVER
2
4
Hold Release
MODE
SINGLE RAID5
SET
ONE UNIT
19