PIONEER Service Manual. A subscription to, or additional copies of, Also test with plug reversed Earth PIONEER Service Manual may be obtained at a nominal (Using AC adapter ground charge from PIONEER. plug as required)
Page 3
IMPORTANT LASER DIODE CHARACTERISTICS MAXIMUM OUTPUT POWER : 5 mW THIS PIONEER APPARATUS CONTAINS WAVELENGTH : 780 – 785 nm LASER OF CLASS 1. SERVICING OPERATION OF THE APPARATUS S H O U L D B E D O N E B Y A S P E C I A L LY INSTRUCTED PERSON.
Page 4
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. CDJ-1000MK3...
ADG1154 For European type region Caution Do not use this power cord set in Taiwan. European two-pin plug ADG7097 For Taiwan exclusively Caution For use in Taiwan only. In other areas, please do not use. Taiwanese two-pin flat-bladed plug CDJ-1000MK3...
For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING SECTION TLFXJ only KUCXJ only CDJ-1000MK3...
Page 9
DHA1534 Pad (C) DHA1535 Pad (D) DHA1536 Packing Case See Contrast table (2) (2) CONTRAST TABLE CDJ-1000MK3/KUCXJ, WYXJ5 and TLFXJ are constructed the same except for the following: Mark Symbol and Description CDJ-1000MK3/KUCXJ CDJ-1000MK3/WYXJ5 CDJ-1000MK3/TLFXJ > Power Cord ADG7021 ADG1154 ADG1154 >...
2.2 EXTERIOR SECTION Refer to "2.3 CONTROL PANEL SECTION". Refer to "2.4 SLOT-IN MECHA. SECTION". CDJ-1000MK3...
Page 11
Rear Panel See Contrast table (2) Heatsink DNG1099 PCB Stay DNH2711 Shield Case DNH2712 (2) CONTRAST TABLE CDJ-1000MK3/KUCXJ, WYXJ5 and TLFXJ are constructed the same except for the following: Mark Symbol and Description CDJ-1000MK3/KUCXJ CDJ-1000MK3/WYXJ5 CDJ-1000MK3/TLFXJ > Inlet Assy DKP3754 DKP3753...
SPCN ASSY CN604 IC403 IC401 SD CARD STEPPING CONTROLER MOTOR TRAVERSE SYSYTEM MECHANISM CN603 LOADING Pitch bend MOTOR Key control at master tempo SD CARD Generates CD digital out CN401 INTERFACE SLOT-IN MECHANISM CN3002 CN3001 SD CARD CONNECTOR SDCB ASSY CDJ-1000MK3...
ANALOG IC501 AUDIO 25 27 IC1512 DATA FL CONTROL OP AMP IC1001 FL UCOM J1004 J1006 CN1007 CN2301 CN1201 J1301 S3001 JA1502 JA1503 JA1501 AUDIO OUT DIGITAL CONTROL DIRECTION TEMPO ZERO ADJ. VR1202 KSWB RSWB SLDB ASSY ASSY ASSY CDJ-1000MK3...
Page 23
÷ The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. ÷ : The power supply is shown with the marked box. CDJ-1000MK3...
3.6 MAIN (4/4) and SLMB ASSYS (FS) (TS) (FS) (TS) (FS) (TS) (TS) (TS) (SP) (FS) (FS) TO LOADING (SP) MOTOR ASSY-S (ST) (ST) (SP) (ST) (ST) (ST) (SP) TO STEPPING MOTOR (ST) SLMB ASSY (DWS1366) CDJ-1000MK3...
Page 31
MAIN ASSY (DWG1591) (ST) (ST) (SP) (SP) : RF Signal Route (FS) : Focus Servo Signal Route (TS) : Tracking Servo Signal Route (SP) : Spindle Motor Signal Route (ST) : Stepping Motor Signal Route : Loading Motor Signal Route CDJ-1000MK3...
Page 35
MFD, BY LITTELFUSE INK. FOR IC1507. AND IC1503. : Analog Audio Signal Route : Digital Out Signal Route CN601 CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. AEK7003- 491.315 MFD, BY LITTELFUSE INK. FOR IC1513. CN301 CDJ-1000MK3...
Symbol In PCB Symbol In Schematic Part Name Diagrams Diagrams C E B Capacitor Connector Transistor B C E SIDE A Transistor with resistor B C E Field effect SIDE B Chip Part P.C.Board transistor Resistor array 3-terminal regulator CDJ-1000MK3...
TEMPO knob (SLDB Assy) Zero Point ADJ. 0 ± 10mV TEMPO RESET The digital multi- POWER ON meter which can be measured to 0.1mV. 3 pin: ADCT Set the TEMPO knob to the 2 pin: ADIN center "0" point. CDJ-1000MK3...
Remove the screw fixing the adjust plate, then screw it into the hole corresponding to the value (-1, -2, -3, +1, or +2) for a load to be added: -1, -2, -3 : To decrease the load +1, +2 : To increase the load Adjust plate To decrease To increase the load the load JOG Check Mode : CANCEL POWER OFF CDJ-1000MK3...
In this mode, the version of the software program for each microcomputer and the error history can be checked. Version Check Mode : ON Version check mode RELOOP/EXIT Main section MAIN Ver 1.00 POWER OFF Player section Hold the key pressed for about 10 seconds. PLAYER Ver 1.00 Operation section Ver 1.00 To error history display mde CDJ-1000MK3...
Communication error between operatin section and main section The error indication is cleared when the communication is finished . E-8709 Error in mechanical operations Unrecoverable: Turn the power off. The error indication will be cleared. Notes: E-8304, E-8305 and E-8709 are not stored into the internal memory. CDJ-1000MK3...
Page 81
Position other than the maximum TOUCH/BRAKE It will become JOG load check mode, and top speed and time will be displayed on a FL dot-matrix part. Maximum position (fully clockwise direction) Display Check Mode : CANCEL POWER OFF CDJ-1000MK3...
Page 82
CUE Area : If a RELEASE/START knob is turned to the clockwise direction, the number of display dots will increase. Playing Address : If a TEMPO slider knob is moved to + side, the number of display dots will increase. CDJ-1000MK3...
Page 84
PLAY/PAUSE Servo All Off TIME TRACK SEARCH ¢/4 SEARCH ¡ Track Search F/R Slider Move Fwd SEARCH 1 Error Rate Count Slider Move Rev FOLDER SEARCH |/\ Eject EJECT Step Command Mode Change MASTER TEMPO Mode Change MASTER TEMPO CDJ-1000MK3...
Page 85
A series of operations for startup will be performed step by step. Each time the FOLDER SEARCH FWD button is pressed, the step is advanced. Each time the FOLDER SEARCH REV button is pressed, the step is reversed. Each step and its operation is shown in the table below: CDJ-1000MK3...
Page 86
Mode Change (termination of Test Operation mode) When the MASTER TEMPO button is pressed during Test Operation mode, the MASTER TEMPO LED goes dark, the servo is stopped, then the unit shifts to Player Operation mode, described above. CDJ-1000MK3...
7.1.2 HOW TO UPGRADE THE SOFTWARE OF THE MICROCOMPUTER POWER REC MODE RELOOP/EXIT REC MODE RELOOP/EXIT FL Display N O - D l S C Release POWER ON CDJ-1000MK3 Version up disc POWER FL Display E R R O R Failure Repeat from Automatically the beginning. POWER OFF...
After a disc is loaded, loading Long press processing and startup processes begin. of the key In the power ON If a disc is loaded, the playback process starts. Reading data, etc. Distinction between DVD/CD CD playback process Eject /MP3 playback CDJ-1000MK3...
Page 89
Focus on Detection of the 8-cm adaptor Coarse adjustment of focus position Searching for 0m01s time point Offset adjustment of the tracking actuator Spindle starts rotating at 4000 rpm. Tracking balance adjustment Adjustment of tracking-error amplitude Off-track threshold adjustment CDJ-1000MK3...
Page 91
Set the MAIN Assy in the upright position, by engaging it at the two hooks. MAIN Assy Bottom plate Bottom view Remove the four screws. MAIN Assy Bottom view MAIN Assy Bottom view Stand the MAIN Assy. MAIN Assy Bottom view Diagnosis Diagnosis Bottom view CDJ-1000MK3...
Remove the seven screws. Remove the bottom plate. Rear view Bottom plate Remove the five screws. Bottom view Remove the four screws. MAIN Assy Bottom view Remove the control panel section. Bottom view Control panel section Stand the MAIN Assy. Bottom view CDJ-1000MK3...
Page 93
Set the MAIN Assy in the upright position, by engaging it at the two hooks. Disconnect the two connectors. Bottom view Disconnect the three flexible cables. MAIN Assy CN603 CN605 MAIN Assy CN604 CN601 CN602 Bottom view Remove the two screws. Remove the shield case. Bottom view Shield Case CDJ-1000MK3...
Page 94
Remove the earth lead unit by removing the one screw. Remove the four DM screws. Earth lead unit Remove the four float spring G5s. Remove the slot-in mecha. section. Float spring G5 Damper Slot-in mecha. section CDJ-1000MK3...
Page 95
Mecha. plate Before shipment, be sure to clean the pickup lens, using the following cleaning materials: Cleaning liquid : GEM1004 Unhook the four hooks. Cleaning paper : GED-008 Remove the slot-in mecha. G11 Assy. Pickup lens Slot-in mecha. G11 Assy CDJ-1000MK3...
Page 96
Disconnect the flexible cable. Remove the five screws. Remove the three screws. Remove the JOG section. Remove the SW ring. Caution: Be careful not to lost SW spring 25. MFLB Assy SW spring 25 SW ring CN1001 Bottom view JOG section CDJ-1000MK3...
Page 97
Mount the two joint gears 2. Note: When mounting joint gears 2, engage the gears, being careful not to move joint gear 1. Slit Cam plate Positioning hole Joint gear 1 Gear stopper Joint gear 2 Joint gear 3 Forced eject pin Cam plate CDJ-1000MK3...
Page 98
(←) (12 positions in total) on the sheet SW. Cam plate Default value "0" To decrease To increase SW cushion HH48/2 Engraved arrow SW cushion HH48/2 the load the load Note: For details on adjustment, see "Load Sheet SW Adjust plate Check mode for the JOG Dial." CDJ-1000MK3...
Connect with the servo DSP (Not used, pull down) − VssQ Ground Data bus − VccQ V+3R3 Power supply for I/O (3.3V) Data bus Data bus Data bus Data bus Data bus Data bus Data bus Data bus Data bus − VssQ Ground CDJ-1000MK3...
Page 100
Power supply for I/O (3.3V) − N.C. Not used Bus cycle start signal Read strobe XWE0 Write strobe XWE1 Write strobe − N.C. Not used − N.C. Not used RD/WR RDWR Read/write − AUDSYNC XAUSYC For development − VssQ Ground CDJ-1000MK3...
Page 101
141 PINT10 Not used − 142 PINT9 UPDATE For development 143 PINT8 MOT EMPTY Motorola FIFO empty signal input (High with EMPTY) 144 MDO SHMD0 Clock mode setting (pull up with 3.3V) − 145 Vcc-PLL1 V+1R8 Power supply for PLL1 CDJ-1000MK3...
Page 102
Not used 191 DREQ0 XDREQ0 DMA request 0 (FPGA) − 192 DREQ1 XDREQ1 Not used (connect to FPGA) 193 RESETTP RSTCPU Reset input 194 CA Chip active (pull up with 3.3V) 195 MD3 SHMD3 Clock mode setting (pull down) CDJ-1000MK3...
Page 103
202 AN3 Not used − − 203 AN4 Not used − − 204 AN5 Not used − 205 AVcc V+3R3 Analog power supply (3.3V) − − 206 AN6 Not used − − 207 AN7 Not used − 208 AVss Ground CDJ-1000MK3...
Page 104
Configuration mode setting (connect to 2.5V) V+2R5FPGA Configuration mode setting (connect to 2.5V) I/O DUAL ATA7 ATA data bus I/O DUAL DIS_DIN FL microcomputer (IC1002) data output − Ground − VCCO V+3R3 Power supply for I/O IO/VREF DIS_XCS FL microcomputer (IC1002) chip select input CDJ-1000MK3...
Page 105
IO/VREF CPU data bus CPU data bus CPU data bus XWE1 CPU write signal − Ground CPU data bus IO/VREF CPU data bus − VCCO V+3R3 Power supply for I/O IO/VREF CPU data bus CPU data bus − Ground CDJ-1000MK3...
Page 106
140 I/O DCI XDREQ1 Not used (connect to CPU) 141 I/O DCI TI_HRDY DSP (IC401) data ready signal 142 HSWAP_EN V+2R5FPGA Bus state setting in configuration (pull down) 143 PROG_B FPGA_XPRG PRG signal for FPGA configuration 144 TDI N.C. Not used CDJ-1000MK3...
Page 107
Data input/output to FLASH ROM FDT6 FDT6 Data input/output to FLASH ROM FDT7 FDT7 Data input/output to FLASH ROM Chip enable output to FLASH ROM FADR10 FADR10 Address output to FLASH ROM Output enable output to FLASH ROM MMOD MMOD Connect to VSS CDJ-1000MK3...
Page 108
LOUT − AVDDD AVDDD Power supply (VA3V) VCOF VCOF VCO control voltage TRCRS TRCRS Input for TRCRS (Track Cross) generation − AVDDC AVDDC Power supply (VA3V) WBLIN WBLIN Connect to VSS CSLFLT CSLFLT RFDIF RFDIF − AVSSC AVSSC GNDA CDJ-1000MK3...
Page 109
IODRY Ready output to the host 139 NDMACK NDMACK Host DMA acknowledge input 140 INTRQ INTRQ Interrupt output to the host 141 NIOCS16 NIOCS16 Data bus width select 142 DA1 Assress input 143 NPDIAG NPDIAG 144 DA0 Assress input CDJ-1000MK3...
Page 110
171 HDD7 HDD7 Data input/output − 172 VDDH VDDH Power supply (VD5V) 173 NRESET NRESET Reset input from the host 174 MASTER MASTER Connect to VSS 175 P0/SERIAL LPS1 Loading mecha SW input 176 P1/SERIAL LPS2 Loading mecha SW input CDJ-1000MK3...
Page 111
Clockwise direction: Vcc side P95/ANEX0 VINYL SPEED ADJUST input Clockwise direction: Vcc side MODEL1 Model setting 1 (pull up with 5V) Distinguish between CDJ-800MK2 and CDJ-1000MK3. P93/DA0 MODEL2 Model setting 2 (pull up with 5V) Distinguish between CDJ-800MK2 and CDJ-1000MK3. −...
Page 112
Not used (Connect to GND) − AVSS GNDD − − P100/AN0 Not used (Connect to GND) − VREF V+5D Reference voltage input of A/D converter − AVcc V+5D Reference voltage input of A/D converter − − 100 P97/XADTRG Not used (Connect to GND) CDJ-1000MK3...
EJECT button. Loop-in point adjust 13. JOG ADJUST dial 4. LOOP OUT (OUT ADJUST) button/indicator Use to adjust the felt resistance (light/heavy) of the jog dial when Loop-out point input it is rotated. Loop-out point adjust 5. RELOOP/EXIT button CDJ-1000MK3...
CONTROL connector on a rotated counterclockwise, play accelerates to full speed quickly; Pioneer DJ mixer, the DJ mixer can be used to control the CD when the dial is rotated clockwise, play accelerates more slowly player for fader start play and back cue.
Lights during VINYL mode. scaled over the entire width of the display. ¶ During elapsed time display, the bar graph's indicator segments turn on from left to right. CDJ-1000MK3...
Page 116
GEM1036 (ZLX-ME413A) Refer to "2.4 SLOT-IN MECHA. SECTION". Grease (ZLB-HFD1600) Refer to "2.3 CONTROL PANEL SECTION". Cleaning Name Part No. Remarks Cleaning liquid GEM1004 Used to pickup lens cleaning. Refer to "2.5 TRAVERSE MECHA. Assy-S", "7.1.3 DISASSEMBLY". Cleaning paper GED-008 CDJ-1000MK3...