Page 1
COMPACT COMPONENT SYSTEM SYSTEME DE COMPOSANTS COMPACT FS-GD7 D I G I T A L INSTRUCTIONS MANUEL D’INSTRUCTIONS —Consists of CA-FSGD7 and SP-FSGD7 —Composé du CA-FSGD7 et du SP-FSGD7 LVT1348-002A...
Page 2
Mises en garde, précautions et indications diverses CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated...
Page 3
Consult the dealer or an experienced radio/TV technician for help. CAUTION Changes or modifications not approved by JVC could void the user’s authority to operate the equipment. For the main unit: Declaration of Conformity...
Introduction ... 2 Precautions ... 2 How to Read This Manual ... 2 Getting Started ... 3 Step 1: Unpack ... 3 Step 2: Prepare the Remote Control... 3 Step 3: Hook Up... 4 Changing the Scanning Mode ... 6 Before Operating the System ...
Precautions Installation • Install in a place which is level, dry and neither too hot nor too cold—between 5°C and 35°C. • Install the System in a location with adequate ventilation to prevent internal heat buildup inside the System. DO NOT install the System in a location near heat sources, or in a place subject to direct sunlight, excessive dust or vibration.
Step 1 :Unpack the package and check the accessories. Step 2 : Prepare the remote control. Step 3 : Hook up the components such as AM/FM antennas, speakers, etc. (see pages 4 to 6). Finally plug the AC power cord. Now you can operate the System.
Step : Hook Up If you need more detailed information, see page 6. Illustrations of the input/output terminals below are typical examples. When you connect other components, refer also to their manuals, since the terminal names actually printed on the rear may vary.
Page 9
For better FM/AM reception Vynile-covered wire (not supplied) Extend it horizontally. AM loop antenna Keep it connected. Disconnect the supplied FM antenna, and connect to an outdoor FM antenna using a 75 Ω wire with coaxial type connector. Outdoor FM antenna (not supplied) SUBWOOFER...
To assemble and connect the AM loop antenna To assemble the AM loop antenna To connect the AM loop antenna 1 Hold 2 Insert • If the AM loop antenna wire or speaker cords are covered with vinyl, remove the vinyl to expose the tip of the antenna by twisting the vinyl.
Before Operating the System Playable Disc Types This System has been designed to play back the following discs: Disc Type Mark (Logo) DVD Video DVD Audio Video CD (VCD) DIGITAL VIDEO Super Video CD (SVCD) SUPER VIDEO COMPACT Audio CD DIGITAL AUDIO CD-R The System can play back CD-R or CD-RW...
Display Indicators The indications on the display teach you a lot of things while you are operating the System. Before operating the System, be familiar with when and how the indicator illuminates on the display. 1 Disc tray indicators • 1–5: Disc tray number indicators. •...
Page 13
Indications on the main display while operating a disc While playing back a disc: • DVD Video: Chapter no. Elapsed playing time • By pressing SHIFT+DISPLAY, you can show the current title and chapter numbers for a few seconds. • DVD Audio: Elapsed playing time Track no.
Daily Operations Numeric buttons DISPLAY RETURN TOP MENU GROUP/TITLE 4,¢ FM/PLAY MODE SHIFT 3D PHONIC —Playback Turn on the power. The STANDBY lamp on the main unit turns off. • Without pressing AUDIO by pressing one of the source selecting buttons in the next step.
Listening to the Radio To select the band (FM or AM) To tune in to a station While FM or AM is selected... Remote control: Main unit: sec. Frequency starts changing on the display. When a station (frequency) with sufficient signal strength is tuned in, the frequency stops changing.
Playing Back a Disc Before operating a disc, be familiar how a disc is recorded. • DVD Video comprises of “Titles” which includes “Chapters,” DVD Audio/MP3 comprise of “Groups” which includes “Tracks,” and CD/SVCD/VCD comprise of only “Tracks.” • For MP3/JPEG playback, see “Operations on the CONTROL Screen”...
Page 17
To locate a particular portion While playing a disc except MP3... • No sound comes out while searching on DVD Video/ SVCD/VCD. To return to normal playback, press DVD/CD 3. Remote To locate an item directly ONLY You can select a title/chapter/track directly and start playback.
Playing Back from the PC This System is equipped with a USB terminal on the front panel. You can connect your PC to this terminal and enjoy sound reproduced through your PC. When you connect your PC for the first time, follow the procedure below.
Daily Operations Remote control CANCEL A.STANDBY DISPLAY DIMMER SLEEP FADE BASS/TREBLE MUTING AUDIO VOL +/– ENTER 2,3,5,∞ DVD LEVEL AHB PRO SOUND SHIFT TURBO Main unit —Sound&Other Adjustments Adjusting the Volume You can adjust the volume level from level 0 (VOL MIN) to level 31 (VOL MAX).
Making DVD Voice Clear—CLEAR VOICE Remote ONLY This function allows you to easily understand the dialog of DVD even with the volume turned down. • This function only works for center-channel signal encoded multi-channel disc. Canceled Presetting Automatic DVD Sound Increase Remote Level—DVD LEVEL ONLY...
Changing the Picture Tone—VFP (Video Remote Fine Processor) ONLY While showing a playback picture on the TV screen, you can select the preset picture tone, or adjust it and store your own likeliness. To select a preset picture tone Activate VFP. NORMAL GAMMA BRIGHTNESS...
Remote Setting the Clock ONLY Without setting the built-in clock, you cannot use the Daily Timer (see page 30) and Sleep Timer (see page 18). • To exit from the clock setting, press CLOCK/TIMER as required. • To go back to the previous step, press CANCEL. Activate the clock setting mode.
Unique DVD/VCD Operations Remote control PAGE -/+ DVD/CD 3 ENTER SUBTITLE AUDIO SHIFT Selecting the Sound Track For DVD Video: While playing back a chapter containing audio languages, you can select the language to listen to. For DVD Audio: While playing back a track containing audio channels, you can select the audio channel to listen to.
Selecting the Subtitle Language For DVD Video: While playing back a chapter containing subtitles in different languages, you can select the subtitle language to display on the TV screen. For SVCD: While playing back a track, you can select the subtitles even if no subtitles are recorded on the disc.
Selecting Browsable Still Pictures • This function is only used while playing DVD Audio. While playing back a track linked to browsable still pictures (B.S.P.), you can select the still picture (turn the page) to be shown on the TV screen. •...
Advanced Disc Operations Remote control CANCEL Numeric buttons DVD/CD 3 5,∞ 4,¢ FM/PLAY MODE SHIFT Main unit DISC1 Programming the Playing Order— Program Play You can arrange the playing order of the chapters or tracks (up to 99) before you start playback. Before starting playback, activate Program Play.
Start playback. Playback starts in the order you have programmed. To skip a step: To pause: To release, press DVD/CD 3. To check the programmed contents Before or after playback... In the reverse order. In the programmed order. To modify the program Before or after playback...
Playing Repeatedly Remote ONLY • You can also select the repeat mode using the on-screen bar (see page 26). Repeat Play You can repeat playback. • For DVD Video: During playing... Canceled Before playback... ALL * Canceled • For DVD Audio: During or before playback...
On-Screen Disc Operations Remote control Numeric buttons DVD/CD 3 ENTER 4,¢ REPEAT On-screen bars DVD Video DISC 8.5Mbps TITLE TITLE 2 CHAP CHAP 3 DVD-VIDEO TIME CHAP. 1/ 3 TIME DVD Audio GROUP 14 TRACK 23 DISC DVD-AUDIO TIME TRACK PAGE SVCD DISC...
Operations Using the On-screen Bar Ex.: Selecting a subtitle (French) for DVD Video: While a disc is selected as the source... Display the on-screen bar with the pull-down menu. DISC 3 8.5Mbps TITLE 2 DVD-VIDEO 8.5Mbps DISC 3 TITLE TITLE 2 DVD-VIDEO TIME TIME...
Select the repeat mode you want. Repeats all discs or all programmed tracks. Repeats a desired portion (see next column). TITLE Repeats the current title. GROUP Repeats the current group. DISC Repeats the current disc (except for DVD). CHAPTER Repeats the current chapter. TRACK* Repeats the current track.
Chapter/Track Search You can search for the chapter (DVD Video) or track (DVD Audio) number to play. While playing, display the on-screen bar with the pull- down menu. Select CHAP. TRACK Display the pop-up window. 8.5Mbps DISC 2 TITLE TITLE 2 CHAP CHAP 3 DVD-VIDEO...
Page 33
To move the highlight bar between group list and track list Moves the bar to the track list. Moves the bar to the group list. To select a group/track in the list Move the highlight bar to a desired item. •...
Remote control CANCEL Timer Operations Setting the Daily Timer Using Daily Timer, you can wake up with your favorite music. You can store three Daily Timer settings; however, you can activate only one of the timers at a time. • To exit from the timer setting, press CLOCK/TIMER as AUDIO required.
Page 35
5 Select the volume level. • You can select the volume level (“1” to “MAX” and “VOL – –”). If you select “VOL – –,” the volume is set to the last level when the System has been turned off. Once settings are complete, the Timer setting information appears in sequence.
Setup Menu Operations Remote control ENTER SET UP Setup Menu Icons The icon for the selected Setup Menu will be highlighted. Ex.: LANGUAGE Setup Menu is selected. LANGUAGE MENU LANGUAGE ENGLISH ENGLISH AUDIO LANGUAGE SUBTITLE ON SCREEN LANGUAGE ENGLISH SELECT TO SELECT.
Finish the setting. Repeat steps 3 to 4 to set other items on the same Setup Menu. Repeat steps 2 to 4 to set other items on another Setup Menu. To exit from the Setup Menu LANGUAGE Setup Menu You can select the initial languages for disc playback. You can also select the language shown on the TV screen while operating this System.
PICTURE SOURCE You can obtain optimal picture quality by selecting an appropriate option—picture source type (either video source or film source). Select one of the following: AUTO: Normally select this. When playing back a disc containing both video and film sources, the System automatically changes the processing to match it to the picture type (film or video source) of the current chapter.
D. (Dynamic) RANGE COMPRESSION You can compress the dynamic range (the difference between the loudest sound and the softest sound) to enjoy a powerful sound even at a low volume level when listening to Dolby Digital software. This is useful at night. •...
Remote control TV CH+/– SHIFT Operating the TV Operating TV You can operate the JVC’s TV using this remote control. To operate the TV To turn on or off TV/VIDEO the TV: TV VOL+/– To adjust the TV volume: To select the TV channel:...
Additional Information Learning More about This System Getting Started (see pages 3 to 6) Changing the Scanning Mode: • To enjoy the progressive video picture, connect a TV with the progressive video input using component video cord. Daily Operations—Playback (see pages 10 to 14) Listening to the Radio: •...
Page 42
Advanced Disc Operations (see pages 22 to 24) Programming the Playing Order—Program Play: • If you try to program the 100th track, “MEM FULL (memory full)” appears on the display. • While programming steps... Your entry will be ignored if you have tried to program an item number that does not exist on the disc (for example, selecting track 14 on a disc that only has 12 tracks).
Maintenance To get the best performance of the System, keep your discs and mechanism clean. Handling discs • When removing the disc from its case, hold it at the edge while pressing the center hole lightly. • Do not touch the shiny surface of the disc, or bend the disc. •...
Troubleshooting If you are having a problem with your System, check this list for a possible solution before calling for service. General: Adjustments or settings are suddenly canceled before you finish. ] There is a time limit. Repeat the procedure again. Operations are disabled.
Language Code List Afar Abkhazian Afrikaans Ameharic Arabic Assamese Aymara Azerbaijani Bashkir Byelorussian Bulgarian Bihari Bislama Bengali, Bangla Tibetan Breton Catalan Corsican Czech Welsh Danish Bhutani Greek Esperanto Estonian Basque Persian Finnish Fiji Faroese Frisian Irish Scots Gaelic Galician Guarani Gujarati Hausa Hindi...
OPTICAL DIGITAL OUT Signals DIGITAL AUDIO Playback disc DVD Video with 48 kHz, 16/20/24 bit Linear PCM with 96 kHz, Linear PCM with Dolby Digital with DTS DVD Audio with 48/96/192 kHz, 16/20/24 bit Linear PCM with 44.1/88.2/176.4 kHz, 16/20/24 bit Linear PCM with Dolby Digital with DTS SVCD, VCD, CD...
Parts Index Refer to the pages to see how to use the buttons and controls. Remote control 23, 31, 36 11, 13, 16 – 18, 20 – 22, 27, 28 10, 12, 13, 21, 23, 29 11, 13, 21 12, 21, 23, 29 10, 15, 36 11 –...
Specifications Amplifier section Output Power: 90 W per channel, min. RMS, driven into 6 Ω at 1 kHz with no more than 10% total harmonic distortion. Analog input: AUX: Sensitivity/Impedance (at 1 kHz) 400 mV/47 kΩ USB input: USB Ver.1.1 Digital output: OPTICAL DIGITAL OUT: –21 dBm to –15 dBm (660 nm ±30 nm)
Page 49
Introduction ... 2 Précautions ... 2 Comment lire ce manuel ... 2 Pour démarrer ... 3 Étape 1: Déballage ... 3 Étape 2: Préparation de la télécommande ... 3 Étape 3: Connexions... 4 Changement du mode de balayage... 6 Avant d’utiliser la chaîne ... 7 Types de disques reproductibles ...
Précautions Installation • Installez la chaîne dans un endroit plat, sec, et ni trop chaud, ni trop froid—entre 5°C et 35°C. • Installez la chaîne dans un endroit avec une bonne ventilation pour éviter tout échauffement intérieur de l’appareil. N’INSTALLEZ PAS la chaîne dans en endroit proche d’une source de chaleur ou sujet à...
Étape 1 :Déballage et vérification des accessoires. Étape 2 :Préparation de la télécommande. Étape 3 :Connexion des composants tels que les antennes AM/FM, les enceintes etc.(voir pages 4 à 6). Finalement, branchez le cordon d’alimentation. Maintenant, vous pouvez utiliser la chaîne. Pour démarrer Étape 1: Déballage Après le déballage, vérifiez que tous les éléments suivants...
Étape : Connexions Si vous avez besoin d’informations plus détaillées, voir page 6. Les illustrations des prises d’entrée/sortie ci-dessous sont des exemples typiques. Quand vous connectez d’autres appareils, référez-vous aussi à leurs modes d’emploi car le nom des prises imprimé au dos de l’appareil peut varier.
Page 53
Pour une meilleure réception FM/AM Fil recouvert de vinyle (non fourni) Étendez-le horizontalement. Antenne cadre AM Gardez-la connectée. Déconnectez l’antenne FM fournie et connectez l’appareil à une antenne FM extérieure en utilisant un connecteur de type coaxial 75 Ω. Antenne FM extérieure (non fournie) SUBWOOFER...
Pour assembler et connecter l’antenne cadre AM Pour assembler l’antenne cadre AM Pour connecter l’antenne cadre AM 1 Maintenez 2 Insérez • Si les fils de l’antenne cadre AM ou des cordons d’enceinte sont recouverts de vinyle, retirez-le pour mettre à nu l’âme de l’antenne en torsadant la partie en vinyle.
Avant d’utiliser la chaîne Types de disques reproductibles Cette chaîne a été conçue pour reproduire les disques suivants: Type de Marque (Logo) disque DVD Vidéo DVD Audio CD Vidéo (VCD) DIGITAL VIDEO Super CD Vidéo SUPER VIDEO (SVCD) COMPACT CD Audio DIGITAL AUDIO CD-R Cette chaîne peut reproduire les CD-R ou CD-...
Indicateurs d’affichage Les indications sur l’affichage vous donnent beaucoup d’informations pendant l’utilisation de la chaîne. Avant d’utiliser la chaîne, familiarisez-vous avec les indicateurs, et en particulier, quand et comment ils s’allument sur l’affichage. 1 Indicateurs de plateau à disque • 1–5: Indicateurs de numéro de plateau à disque. •...
Page 57
Indications sur l’affichage principal pendant la lecture d’un disque Lors de la lecture d’un disque: • DVD Vidéo: No de chapitre Durée de lecture écoulée • En appuyant sur SHIFT+DISPLAY, vous pouvez afficher le titre actuel et le numéros de chapitre pendant quelques secondes.
Opérations quotidiennes Touches numériques DISPLAY RETURN TOP MENU GROUP/TITLE 4,¢ FM/PLAY MODE SHIFT 3D PHONIC Mise sous tension de l’appareil. Le témoin STANDBY s’éteint sur l’appareil. • Sans appuyer sur AUDIO tension quand vous appuyez sur une des touches de sélection de source à...
Écoute de la radio Pour choisir la bande (FM ou AM) Pour accorder une station Quand FM ou AM est choisi... Télécommande: Appareil: sec. La fréquence change sur l’affichage. Quand une station (fréquence) avec un signal suffisamment fort est accordée, la fréquence s’arrête de changer. •...
Lecture d’un disque Avant d’utiliser un disque, familiarisez vous avec la façon dont un disque est enregistré. • Les DVD Vidéo sont composés de “titres” qui eux-mêmes sont composés de “chapitres”, les DVD Audio/MP3 sont composés de “groupes” qui eux-mêmes sont composés de “plages”, et, finalement, les CD/SVCD/VCD sont composés uniquement de “plages”.
Page 61
Pour localiser un passage particulier Lors de la lecture d’un disque non MP3... • Aucun ne sort pendant la recherche sur un DVD Video/ SVCD/VCD. Pour retourner à la lecture normale, appuyez sur DVD/CD 3. Pour localiser un élément directement Vous pouvez choisir un titre, un chapitre ou une plage directement et démarrer la lecture.
Lecture à partir de l’ordinateur Cette chaîne est munie d’une prise USB sur le panneau avant. Vous pouvez connecter votre ordinateur à cette prise et écouter les sons reproduits par votre ordinateur. Pour connecter votre ordinateur pour la première fois, suivez la procédure ci-dessous.
Opérations quotidiennes Télécommande CANCEL A.STANDBY SLEEP BASS/TREBLE ENTER SHIFT Appareil —Ajustement du son et autres ajustements Ajustement du volume Vous pouvez ajuster le niveau de volume du niveau 0 (VOL MIN) au niveau 31 (VOL MAX). Télécommande: DISPLAY DIMMER CLOCK/ TIMER FADE MUTING...
Pour rendre plus claires les voix d’un DVD— Remote CLEAR VOICE ONLY Cette fonction vous permet de comprendre plus facilement les dialogues d’un DVD même si le volume est réglé à un niveau bas. • Cette fonciton agit uniquement sur le signal du canal central d’un disque codé...
Changement de la tonalité de l’image—VFP Remote (Video Fine Processor) ONLY Lors de l’affichage d’une image de lecture sur l’écran du téléviseur, vous pouvez choisir une tonalité d’image préréglée, ou l’ajuster et la mémorisée comme réglage personnalisé. Pour choisir une tonalité d’image préréglée Mettez en service la fonction VFP.
Remote Réglage de l’horloge ONLY Sans régler l’horloge intégrée, vous ne pouvez pas utiliser la minuterie quotidienne (voir page 30) et la minuterie d’arrêt (voir page 18). • Pour quitter le réglage de l’horloge, appuyez sur CLOCK/ TIMER autant de fois que nécessaire. •...
Opérations spécialisées pour les DVD/VCD Télécommande PAGE -/+ DVD/CD 3 ENTER SUBTITLE AUDIO SHIFT Sélection de la piste sonore Pour les DVD Vidéo: Lors de la lecture d’un chapitre contenant plusieurs langues audio, vous pouvez choisir la langue à écouter. Pour les DVD Audio: Lors de la lecture d’une plage contenant plusieurs canaux audio, vous pouvez choisir le canaux à...
Sélection de la langue des sous-titres Pour les DVD Vidéo: Lors de la lecture d’un chapitre contenant des sous-titres en différentes langues, vous pouvez choisir la langue des sous-titres à afficher sur l’écran du téléviseur. Pour les SVCD: Pendant la lecture d’une plage, vous pouvez choisir les sous-titres, même si aucun sous-titre n’est enregistré...
Sélection d’image fixes affichables • Cette fonction peut être utilisée uniquement lors de la lecture d’un DVD Audio. Lors de la lecture d’une plage liée avec des images fixes affichables (B.S.P.), vous pouvez choisir l’image fixe (tourner la page) à afficher sur l’écran du téléviseur. •...
Opérations avancées des disques Télécommande CANCEL Touches numériques DVD/CD 3 5,∞ 4,¢ FM/PLAY MODE SHIFT Appareil DISC1 Programmation de l’ordre de lecture— Lecture programmée Vous pouvez arranger l’ordre de lecture des chapitres ou des plages (99 maximum) avant de démarrer la lecture. Avant de démarrer la lecture, mettez en service la lecture programmée.
Démarrez la lecture. La lecture démarre dans l’ordre de programmation. Pour sauter une étape: Pour faire une pause: Pour reprendre la lecture, appuyez sur DVD/CD 3. Pour vérifier le contenu programmé Avant ou après la lecture... Dans l’ordre inverse. Dans l’ordre programmé. Pour modifier le programme Avant ou après la lecture...
Répétition de la lecture Remote ONLY • Vous pouvez aussi choisir le mode de répétition en utilisant la barre sur l’écran (voir page 26). Lecture répétée Vous pouvez répéter la lecture. • Pour les DVD Vidéo: Pendant la lecture... Annulée Avant la lecture...
Opération des disques en utilisant l’affichage sur l’écran Télécommande Touches numériqu DVD/CD 3 ENTER 4,¢ REPEAT Barres sur l’écran DVD Vidéo DISC 8.5Mbps TITLE TITLE 2 CHAP CHAP 3 DVD-VIDEO TIME CHAP. TIME DVD Audio GROUP 14 TRACK 23 DISC DVD-AUDIO TIME TRACK...
Opérations en utilisant la barre sur l’écran Ex.: Sélection d’un sous-titre (français) pour un DVD Vidéo: Quand un disque est choisi comme source... Affichez la barre sur l’écran avec le menu déroulant. 8.5Mbps DISC 3 TITLE 2 DVD-VIDEO 8.5Mbps DISC 3 TITLE TITLE 2 DVD-VIDEO...
Page 75
Choisissez le mode de répétition souhaité. TOUTES Répète tous les disques ou les plages programmées. Répète un passage souhaité (voir la colonne suivante). TITRE Répète le titre actuel. GROUPE Répète le groupe actuel. DISQUE Répète le disque actuel (sauf pour les DVD). CHAPITRE Répète le chapitre actuel.
Page 76
Recherche de chapitre/plage Vous pouvez recherche le numéro de chapitre (DVD Vidéo) ou de plage (DVD Audio) à reproduire. Pendant la lecture, affichez la barre sur l’écran avec le menu déroulant. Choisissez CHAP. TRACK Affichez la fenêtre contextuelle. 8.5Mbps DISC 2 TITLE TITLE 2 CHAP...
Page 77
Pour déplacer la barre de mise en valeur de la liste des groupes sur la liste des plages. Déplace la barre sur la liste des plages. Déplace la barre sur la liste des groupes. Pour choisir un groupe ou une plage dans la liste Déplacez la barre de mise en valeur sur l’élément souhaité.
Utilisation de la minuterie Télécommande CANCEL Réglage de la minuterie quotidienne En utilisant la minuterie quotidienne, vous pouvez vous réveiller au son de votre musique préférée. Vous pouvez mémoriser trois réglages de minuterie quotidienne; cependant, vous ne pouvez mettre en service qu’une seule de ces minuteries en même temps.
Page 79
4 Pour “TUNER FM” et “TUNER AM”: Choisit un numéro de préréglage (voir page 11). • Choisissez “FM --” ou “AM --” pour la dernière station choisie. For “DISC”: Choisissez le numéro de disque, de groupe, puis le numéro de plage (voir page 12). •...
Utilisation du menu de réglages Télécommande ENTER SET UP Icônes du menu de réglages L’icône pour le menu de réglage choisi est mis en valeur. Ex.: Le menu de réglage LANGUE est choisi. LANGUE LANGUE MENU ANGLAIS LANGUE AUDIO ANGLAIS SOUS-TITRE ARRET LANGUE D’ECRAN...
Terminez le réglage. Répétez les étapes 3 à 4 pour régler un autre élément sur le même menu de réglage. Répétez les étapes 2 à 4 pour régler un autre élément sur un autre menu de réglage. Pour quitter le menu de réglage Menu de réglage LANGUE Vous pouvez choisir la langue initiale pour la lecture des disques.
SOURCE D’IMAGE Vous pouvez obtenir une qualité d’image optimale en choisissant l’option appropriée—type de source d’image (source vidéo ou source de film). Choisissez un des réglages suivants: AUTO: Normalement choisissez ce réglage. Lors de la lecture d’un disque contenant à la fois des sources vidéo et de film, la chaîne change le traitement automatiquement de façon à...
COMPRESS. PLAGE DYN. Vous pouvez compresser la plage dynamique (la différence entre le son le plus fort et le son le moins fort) pour profiter d’un son puissant même à un faible niveau de volume lors de l’écoute d’un support Dolby Digital. C’est pratique la nuit. •...
Commande du téléviseur Télécommande TV CH+/– SHIFT Commande du téléviseur Vous pouvez commander un téléviseur JVC en utilisant cette télécommande. Pour commander le téléviseur TV/VIDEO Pour mettre le téléviseur sous ou hors tension: TV VOL+/– Pour ajuster le volume du téléviseur: Pour choisir le canal de télévision:...
Informations additionnelles Pour en savoir plus sur cette chaîne Pour démarrer (voir pages 3 à 6) Changement du mode de balayage: • Pour profiter d’images vidéo progressives, connectez un téléviseur muni d’une entrée vidéo progressive en utilisant un cordon vidéo en composantes. Opérations quotidiennes—Lecture (voir pages 10 à...
Page 86
Opérations spécialisées pour les DVD/VCD pages 19 à 21) • Pendant la lecture au ralenti, aucun son n’est reproduit. • La fonction de relecture par une simple pression fonctionne uniquement à l’intérieur du même titre, bien qu’elle fonction entre les chapitres. •...
Entretien Afin d’obtenir les meilleures performances de votre chaîne, gardez vos disques et le mécanisme propre. Manipulation des disques • Pour retirer les disques de leur boîte, tenez-les par les côtés et en appuyant légèrement sur le trou central. • Ne touchez pas la surface brillante du disque ni ne le tordez.
Guide de dépannage Si vous des problèmes avec votre chaîne, cherchez d’abord une solution dans cette liste avant d’appeler un réparateur. Général: Les ajustements ou les réglages sont annulés soudainement avant la fin. ] Il y a un temps limite. Recommencez la procédure. L’appareil ne fonctionne pas.
Signaux OPTICAL DIGITAL OUT SORTIE AUDIO NUM. Disque de lecture DVD Vidéo avec 48 kHz, 16/20/24 bits Linear PCM avec 96 kHz, Linear PCM avec Dolby Digital avec DTS DVD Audio avec 48/96/192 kHz, 16/20/24 bits Linear PCM avec 44,1/88,2/176,4 kHz, 16/20/24 bits Linear PCM avec Dolby Digital avec DTS...
Spécifications Section de l’amplificateur Puissance de sortie: 90 W par canal, min. RMS, entraîné sur 6 Ω à 1 kHz avec moins de 10% de distorsion harmonique totale. Entrée analogique: AUX: Sensibilité/Impédance (à 1 kHz) 400 mV/47 kΩ Entrée USB: USB Ver.1,1 Sortie numérique: OPTICAL DIGITAL OUT:...