Download Print this page

Bosch DCN Wireless 2.32 Release Notes page 9

Communication system

Advertisement

DCN Wireless 2.32 Release Notes
Network\Download and License Tool " is
the part "Program Files" in English.
Replace "Program files" into the name of
this folder on your computer as used by
Windows in your language.
Save the file en close Notepad.
After this the Download Tool should
function.
This problem is solved in release 2.32
3.5 Known limitations DCN-SWSMV
3.5.1
Legends in PowerPoint may return to default
values
It may happen that the legends in PowerPoint return
to their default values when PowerPoint is switched
to presentation mode. This is due to a bug in
Microsoft.
Three workarounds are available:
4) First start PowerPoint and switch to presentation
mode before starting the voting in DCN-SWSMV
5) Before running DCN-SWSMV, edit the
PowerPoint presentation yourself, so that the
legends are already have the correct texts
6) After running a (dummy) voting round, save the
PowerPoint presentation (when the legends are
correctly displayed).
3.5.2
Open the pre-defined slide in the Microsoft
PowerPoint presentation failed'
If the languages of Microsoft Windows and
PowerPoint are not the same, the predefined slide
cannot be opened. This is a known bug of Microsoft
of which the details can be found via the following
link:
http://support.microsoft.com/default.aspx?scid=kb;en-
us;320369
Set 'Your locale' under Regional Options of Microsoft
Windows to the language of PowerPoint.
3.6 Known limitations DCN-2.31
3.6.1 Microphone will be reset to default after a
de-init.
When a de-init wired is activated at the WCCU the
microphone is always set to microphone mode
"open" with 2 active microphones.
3.6.2 Wireless Unit Data is cleared when
performing de-init wired.
When a de-init wired is activated at the WCCU the
wireless unit data (like microphone gain) is cleared.
3.6.3 Activated microphone of chairman 1 does
not return after using priority button by
chairman 2.
In a DCN-Wireless system it's possible to use more
than one Wireless Discussion Units as Chairman
Bosch Communications Systems
(refer to chapter 12.4.1 of the Installation & User
Manual).
In case chairman priority is set to 'Temporarily Off'
in WCCU menu 4G and when more than one
Chairman Unit is used, it's possible that when the
microphone of chairman 1 is active and chairman 2
presses the priority button, the microphone of
chairman 1 does not switch on again, when
chairman 2 releases the priority button (even
though delegate microphones do come on again).
3.6.4 Abort system control with DCN-SWSMV
can cause acoustic feedback.
The audio volume of the DCN-Wireless system can
be controlled from the DCN-SWSMV, but this is not
the same volume control as on the WCCU (refer to
figure 12.1 of the Installation & User Manual).
When the audio volume in the WCCU is too high
and the master volume control of the DCN-SWSMV
is used to reduce the audio volume to prevent
acoustic feedback, the acoustic feedback will occur
when the DCN-SWSMV is aborted.
This is normal system behavior; it is mentioned here
to remind the user.
3.6.5 Long time needed for upgrading Wireless
Access Point (DCN-WAP).
The Download and License Tool can be used for
upgrading. When "Down Load Optical" is selected,
all applicable devices connected to the optical
network will be upgraded. In case the DCN-WAP is
connected, it will take more than 30 minutes to
upgrade the DCN-WAP.
Bypass: In case the DCN-WAP does not need to be
upgraded, do not connect the DCN-WAP when
selecting "Down Load Optical".
This is normal system behavior; it is mentioned here
to remind the user.
3.6.6 No audio on Loudspeakers or Headphones
of Wireless Discussion Units, or one of the
enabled Microphones not working
After starting the DCN-Wireless system it might
occur (seldom) that there is no audio on
Loudspeakers or Headphones of Wireless
Discussion Units, or one of the enabled
Microphones not working. (This does not occur
during operation, but only after startup)
A temporarily solution is to restart the
system
The permanent solution is to use a DCN-
WAP with HW-version 1.20 (or higher),
refer to chapter 2.2.4.
en | 9

Advertisement

loading