DeWalt DC901-XE Instruction Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Drill
  5. DC901-XE
  6. Instruction manual
DeWalt DC901-XE Instruction Manual

DeWalt DC901-XE Instruction Manual

Heavy-duty 36v 13 mm (1/2") cordless hammer drill
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
DC901-XE
HEAVY-DUTY 36V 13 MM (1/2") CORDLESS HAMMERDRILL

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DC901-XE

Summary of Contents for DeWalt DC901-XE

  • Page 1 INSTRUCTION MANUAL DC901-XE HEAVY-DUTY 36V 13 MM (1/2") CORDLESS HAMMERDRILL...

  • Page 3: Safety Instructions For Power Tools

    The term “power tool” in the warnings refers to your mains-operated (corded) power Definitions: Safety Guidelines tool or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these 1) WORK AREA SAFETY symbols.

  • Page 4: Electrical Safety

    c) Prevent unintentional starting. Ensure the switch is in the off position g) Use the power tool, accessories and tool bits etc., in accordance with before plugging in. Carrying power tools with your finger on the switch or these instructions and in the manner intended for the particular type of plugging in power tools that have the switch on invites accidents.

  • Page 5: Extension Cords

    • Young children and the infirm. This appliance is not intended for use by • Wear ear protectors when hammering for extended periods of time. Prolonged young children or infirm persons without supervision. Young children should be exposure to high intensity noise can cause hearing loss. Temporary hearing loss supervised to ensure that they do not play with this appliance.

  • Page 6: Important Safety Instructions For Battery Chargers

    buildup of metallic particles should be kept away from charger cavities. Always WARNING: ALWAYS wear proper personal hearing protection that conforms to unplug the charger from the power supply when there is no battery pack in the ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise cavity.
  • Page 7 • The charger is designed to operate on standard household electrical power. • Contents of opened battery cells may cause respiratory irritation. Provide fresh Do not attempt to use it on any other voltage. air. If symptoms persists, seek medical attention. •...

  • Page 8: Charging Procedure

    ion batteries. Help protect our environment and conserve natural resources by PROBLEM POWERLINE returning the spent lithium ion battery to an authorized D WALT service center or to When the charger is used with some portable power sources such as generators or your local retailer for recycling.

  • Page 9: Key Features And Functions

    b. Check to see if receptacle is connected to a light switch which turns power off FIG. 1 when you turn out the lights. c. Move charger and battery pack to a location where the surrounding air temperature is approximately 18 °- 24 °C (65 °F - 75 °F). d.
  • Page 10 Mode Control Collar NOTE: Use the lowest torque setting required to seat the fastener at the desired depth. The lower the number, the lower the torque output. Your drill is equipped with a separate mode control collar (Fig. 1, C) to switch 2.

  • Page 11: Components (Fig. 1)

    DRILLING (FIG. 3) 2. Grasp the chuck sleeve (F) with one hand and use the other hand to secure the tool as shown in Figure 5. Rotate the sleeve counterclockwise (viewed from the CAUTION: When the mode collar is in the drill/hammerdrill mode, the drill will not front) far enough to accept the desired accessory.

  • Page 12: Operation

    FIG. 9 press the release button (G) and firmly pull The DC901-XE heavy-duty cordless hammerdrill is designed for professional drilling the battery pack out of the tool handle. and driving operations. DO NOT use under wet conditions or in presence of flammable Insert it into the charger (Fig.

  • Page 13: Maintenance

    6. Keep the motor running when pulling the bit back out of a drilled hole. This will WARNING: Never use solvents or other harsh chemicals for cleaning the help prevent jamming. non-metallic parts of the tool. These chemicals may weaken the plastic materials used in these parts.

  • Page 14: Three Year Limited Warranty

    Guarantee FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call (AUS) 1800 654 155 or (NZ) 0800 339258 for a free replacement. Applicable to hand held Power Tools, Lasers and Nailers. Three Year Limited Warranty WALT will repair, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase.
  • Page 16 20 Fletcher Road, Mooroolbark, VIC 3138 Australia (03 8720 5100) • 5 Te Apunga Place, Mt Wellington, New Zealand (0800 339258) (JUL08) Part No. N014005 DC901-XE Copyright © 2008 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...

Table of Contents