Page 2
For automatic driver updates, go to: "http://support.ts.fujitsu.com/com/support/index.html" Should you have any technical questions, please contact: • our Hotline/Service Desk (see Service Desk list or visit: "http://ts.fujitsu.com/support/servicedesk.html") • Your sales partner • Your sales office We hope you really enjoy using your new Fujitsu system.
Page 4
Brand names may be protected trademarks of the respective manufacturer and/or protected by copyright. Use of these by third parties for their own purposes may constitute an infringement of the holders’ rights. Further information can be found at "http://ts.fujitsu.com/terms_of_use.html" Order No. Fujitsu Technology Solutions GmbH: A26391-K360-Z320-1-7619, edition 1...
Page 5
LIFEBOOK S762 / S792 Operating Manual Innovative technology Ports and controls Important notes First-time setup of your device Working with the notebook Security functions Connecting external devices Removing and installing components during servicing Settings in BIOS Setup Utility Troubleshooting and tips Technical specifications...
The Windows drivers for your device can be found on our Internet site. The factory installation of your device does not support any other operating system. Fujitsu Technology Solutions accepts no liability whatsoever if any other operating system is used.
Names of CDs, DVDs and titles or designations for other materials, e.g.: "CD/DVD Drivers & Utilities" or "Safety/Regulations" manual indicates a key on the keyboard, e.g: indicates terms and texts that are emphasised or highlighted, e.g.: Do This font not switch off the device Fujitsu Technology Solutions...
Page 14
3 = USB port (USB 3.0) Right side 1 = Optional: ExpressCard slot, SmartCard 4 = LAN port reader or unremovable mSATA module 5 = Security Lock device 2 = Module bay with optical drive 3 = USB port (USB 2.0) Fujitsu Technology Solutions...
Page 15
Ports and controls Rear 1 = VGA monitor port 2 = Modem port Fujitsu Technology Solutions...
Page 16
Ports and controls Bottom 1 = Hard disk service compartment 5 = Port replicator port 2 = Module release 6 = Battery release 3 = Battery release 7 = Vent cover 4 = Rechargeable battery Fujitsu Technology Solutions...
(e.g. petrol station, paintshops), as the transmitted radio waves can cause an explosion or a fire. For information on how to switch radio components on and off, see chapter "Switching the wireless components on and off", Page Fujitsu Technology Solutions...
You will then be able to work for longer before having to recharge the battery. Energy efficiency is increased and the environmental impact is reduced. You save money while protecting the environment. Energy saving under Windows ► Make use of the power management features (see ""Using the power-management features", Page 43"). Fujitsu Technology Solutions...
► Unplug the mains adapter and all external devices from the power socket. ► Disconnect the mains adapter cable and the data cables for all external devices. ► Close the LCD screen. ► To protect against damaging jolts and bumps, use a notebook carrying case to transport your notebook. Fujitsu Technology Solutions...
The surface can be cleaned with a dry cloth. If particularly dirty, use a cloth which has been moistened in mild domestic detergent and then carefully wrung out. To clean the keyboard and the touchpad, if available, you can use disinfectant wipes. Ensure that no liquid enters the device. Fujitsu Technology Solutions...
► Unpack all the individual parts. Packaging Transport ► Check your device for any visible damage which may have occurred during transportation. You may need the packaging in the future, if you need to transport your device. Fujitsu Technology Solutions...
► Connect the power cable (1) to the mains adapter. ► Plug the mains cable (2) into a mains outlet. ► Connect the mains adapter cable (3) to the DC jack (DC IN) of the device. Fujitsu Technology Solutions...
► During installation, follow the instructions on screen. If a Windows operating system is installed on your device, you will find more information on the system and drivers, help programmes, updates, manuals etc. on the device or on the Internet at "http://ts.fujitsu.com/support". Fujitsu Technology Solutions...
Power-on indicator Indicator is lit The notebook is switched on. Indicator is The notebook is in power saving mode. flashing Indicator is not The notebook is switched off or is in Save-to-Disk mode. Fujitsu Technology Solutions...
Page 25
The notebook is in suspend mode and power is being supplied by the first battery. The first battery is charged to between 0% and 12% of maximum capacity. Indicator is not The first battery is not installed. Fujitsu Technology Solutions...
Page 26
The virtual numerical keypad is activated. You can output the characters indicated on the upper right of the keys. Indicator is not key has not been pressed. The virtual numerical keypad is not active. Fujitsu Technology Solutions...
(e. g. from the Windows Start menu, by clicking on Start – Shut Down – OK). Notebook ► If the notebook is not switched off automatically, press the ON/OFF switch for approx. five seconds. ► Close the LCD screen. Fujitsu Technology Solutions...
The figure below shows how to access the different characters on keys with overlaid functions. The example applies when the Caps Lock key has not been activated. The illustrations shown below may differ from your actual device. Alt Gr Fujitsu Technology Solutions...
Page 29
The cursor keys move the cursor in the direction of the arrow, i.e. up, down, left, or right. Cursor keys Cursor controlkeys Start key The Start key opens the Windows Start menu. Startkey Menu key The Menu key invokes the menu for the marked item. Fujitsu Technology Solutions...
The keyboard layout shown below may differ from your actual device. 1 = Valid characters when the 2 = Valid characters when the key is not activated is activated Further information about the status indicators can be found in chapter "Status indicators", Page Fujitsu Technology Solutions...
This key combination increases the brightness of the screen. Decrease volume Fn+F8 Volume This key combination reduces the volume of the integrated loudspeakers. Volume increase Fn+F9 Volume This key combination raises the volume of the integrated loudspeakers. Fujitsu Technology Solutions...
► Enter the settings by clicking Start – (Settings) – Control Panel – Time, Regional and Language Options. Application keys Applicationkeys Your notebook is equipped with five application keys. All application buttons are freely programmable, see "Programming the application keys", Page Fujitsu Technology Solutions...
Page 33
(see "Status indicators", Page 20). Wireless Components key This application key is used to start the WirelessSelector software. The wireless components that have been activated in the BIOS Setup can be switched on and off individually. Fujitsu Technology Solutions...
You can use a key combination to disable the touchpad, to avoid accidentally moving the pointer on the screen (see also "Key combinations", Page 27). Moving the pointer ► Move your finger on the touchpad. Touchpad The pointer will move. Fujitsu Technology Solutions...
► Press and hold the left button and drag the item to the desired position with the finger on the touchpad. The item will be moved. Switching the Touchpad on and off You can switch the Touchpad on and off using a key combination, "Key combinations", Page Fujitsu Technology Solutions...
► To change the ScrollWheel mode, tap the centre of the ScrollWheel until the desired mode is displayed. ► Move the cursor to the window you wish to select. ► Move your finger clockwise on the ScrollWheel. You can scroll down or forwards or can decrease the volume. Fujitsu Technology Solutions...
► Move your finger anticlockwise on the ScrollWheel. You can scroll up or back or can increase the volume. Back one page in Web browser ► Tap the centre of the ScrollWheel. The Web browser returns to the previous page displayed. Fujitsu Technology Solutions...
LCDscreen Notes High-quality TFT displays are installed in notebooks from Fujitsu Technology Solutions GmbH. For technical reasons, TFT monitors are manufactured for a specific resolution. An optimal, clear picture can only be ensured with the correct resolution intended for the relevant TFT monitor. A monitor resolution which differs from the specification can result in an unclear picture.
If you wish to carry out a function test with your webcam, you can use the corresponding test software available at "http://ts.fujitsu.com/support/". Fujitsu Technology Solutions...
If you do not use the batteries for long periods, remove them from the notebook. Never store the batteries in the device. Removing and installing the battery Only use rechargeable batteries approved by Fujitsu Technology Solutions for your notebook. Never use force when fitting or removing a battery.
► Position the battery at the edge. ► Insert the battery into the battery compartment until it engages positively (1). ► Slide the release button in the direction of the arrow (2). ► Complete the removal, see chapter "Finishing component removal", Page Fujitsu Technology Solutions...
The module can now be removed without any further actions being necessary. Removing a module Module Drive WeightSaver ► Slide the release mechanism (1) in the direction of the arrow and hold. ► Now pull the module (2) out of the module bay. Fujitsu Technology Solutions...
Avoid storing a data carrier in areas subject to high temperatures or humidity. You may use both 8-cm and 12-cm data carriers in the optical drive. When using a data carrier of lesser quality, vibrations and reading errors may occur. Fujitsu Technology Solutions...
► Place the data carrier in the drive tray with the printed side facing upwards. ► Remove a data carrier that has been inserted. ► Push in the drive tray until you feel it lock into place. Fujitsu Technology Solutions...
► Switch your notebook off. ► Push a pen or a piece of wire (such as a paperclip) firmly into the opening (1). The drive tray is ejected. You can now pull the drive tray (2) out of the drive. Fujitsu Technology Solutions...
► Clean the dust chamber. ► Insert the ventilation slot cover into the slot (1) at an angle as shown, and ensure that you feel it click into place. ► Complete the removal, see chapter "Finishing component removal", Page Fujitsu Technology Solutions...
If you do not intend to use your notebook for a long period of time: ► Exit power saving mode if necessary via the mouse or keyboard or by switching on the notebook. ► Close all opened programs and completely shut down the notebook. Fujitsu Technology Solutions...
The label should be facing upward. Do not apply excessive force, as otherwise the delicate contact surfaces could be damaged. Memory card Depending on the particular type used, the memory card may protrude slightly from the slot. Fujitsu Technology Solutions...
Wait for the dialogue box which tells you that it is now safe to remove the memory card. ► On devices with card locking: Press on the storage card (1). Memory card The storage card is released and can now be removed. ► Pull the storage card out of the slot (2). Fujitsu Technology Solutions...
Do not use excessive force. Depending on the type, the card may protrude slightly from the slot. Please see the documentation relating to the card for driver installation instructions. Fujitsu Technology Solutions...
If you attach an external microphone, the built-in microphone is disabled. When you connect headphones or external speakers, the built-in speakers are disabled. Information on connecting headphones and a microphone can be found "Connecting external devices", Page Fujitsu Technology Solutions...
► Connect the modem cable to the modem port of the notebook (1). Modem ► Plug the modem cable (2) into the country-specific telephone adapter (3). ► Connect the modem cable to your telephone wall socket (4). Fujitsu Technology Solutions...
► Press on the edge of the SIM card so that it jumps up slightly out of the slot. ► Pull the SIM card out of the slot in the direction of the arrow (1). ► Complete the removal, see chapter "Finishing component removal", Page Fujitsu Technology Solutions...
Working with the notebook Optional Wireless LAN / BlueTooth / UMTS wireless components The installation of radio components not approved by Fujitsu Technology Solutions will invalidate the certifications issued for this device. Depending on the device configuration you ordered, your device will be equipped with Wireless LAN, Bluetooth and / or UMTS.
The optional UMTS module is ready for use immediately. If you have not ordered a UMTS module, you can purchase the accessories for UMTS reception from specialised dealers or from your Fujitsu Technology Solutions dealer. You will find information on establishing the connection with the UMTS network in the documentation for the hardware used.
5 = Serial interface 13 = Connector on the Port Replicator for the docking port on the bottom of the notebook 6 = Parallel port 14 = DC input connector (DC IN) 7 = eSATA port 8 = USB ports Fujitsu Technology Solutions...
► Disconnect the mains adapter cable from the DC socket (DC IN) of the notebook. ► Position the notebook so that it is in line with the back edge of the Port Replicator. ► Place the notebook onto the Port Replicator (1) and ensure that it locks into place correctly. Fujitsu Technology Solutions...
If the notebook cannot be shut down properly, press the ON/OFF button on the Port Replicator for approx. four seconds. The notebook will switch off. Any unsaved data may however be lost. Fujitsu Technology Solutions...
► Switch the notebook off. ► Pull the unlocking lever in the direction of the arrow (1), until you hear the notebook unlatch. ► Lift off the notebook (2). Fujitsu Technology Solutions...
The fingerprint sensor can record an image of a fingerprint. With additional fingerprint software, this image can be processed and used instead of a password. ► You must install the fingerprint software in order to be able to use the fingerprint sensor (1). Fujitsu Technology Solutions...
Utility, while the user password only provides some of the functions. You can only set a user password if a supervisor password has already been assigned. Please refer to the ""Settings in BIOS Setup Utility", Page 79 section for a description of how to call up and operate the BIOS Setup Utility. Fujitsu Technology Solutions...
Password protection for booting of the operating system With the supervisor password you have set in the BIOS Setup Utility (see section "Setting supervisor and user password", Page 58), you can also prevent booting of the operating system. Operating system Fujitsu Technology Solutions...
► From the Exit menu, choose the option Exit Saving Changes. ► Press the Enter key and select Yes. The notebook reboots and your hard disk is now protected with a password. The system will ask you to enter the password when the notebook is restarted again. Fujitsu Technology Solutions...
If you do not want to change any other settings you can exit the BIOS Setup. ► From the Exit menu, choose the option Exit Saving Changes. ► Press the Enter key and select Yes. The notebook will restart and the settings will be adopted. Fujitsu Technology Solutions...
Setup Notice: Changes have been saved is displayed to confirm that the text has been saved. ► From the Exit menu, choose the option Exit Saving Changes. ► Press the Enter key and select Yes. The notebook will restart and the Owner Information will be adopted. Fujitsu Technology Solutions...
► Mark the TPM Security Chip Setting field and press the Enter key. ► Select Disabled to deactivate the TPM. ► From the Exit menu, choose the option Exit Saving Changes. ► Press the Enter key and select Yes. Your notebook will now restart and TPM will be disabled. Fujitsu Technology Solutions...
In order to be able to take advantage of all the security features of your notebook, you will need a CardOS SmartCard from Fujitsu Technology Solutions. The SmartCard can only be used with a PIN, offering maximum protection even if you lose the SmartCard.
Disconnecting devices from the notebook 1. Turn off your notebook and all external devices. 2. Unplug your notebook and all devices from the mains sockets. 3. Disconnect the cables for your external devices following the instructions. Devices Peripheraldevices Fujitsu Technology Solutions...
You can also switch back and forth between the external monitor and the notebook’s LCD monitor, see chapter "Key combinations", Page You can display the same picture on the external monitor and the notebook LCD screen simultaneously. Fujitsu Technology Solutions...
► Select Start symbol – (Settings) – Control Panel – Hardware and Sound – Sound. ► Mark Realtek HDMI Output. ► Select Properties – Supported formats. ► Deactivate the settings DTS audio and Dolby digital. ► Confirm the settings with OK. Fujitsu Technology Solutions...
The devices connected to the parallel or serial port require drivers. Your operating system already includes many drivers. If the required drive is missing, install it. Current drivers are usually available on the Internet or will be supplied on a data medium. Fujitsu Technology Solutions...
Additional information can be found in the documentation for the USB devices. ► Connect the data cable to the external device. ► Connect the data cable to a USB port of the notebook. Device drivers USB devices will be automatically recognised and installed by your operating system. Fujitsu Technology Solutions...
You can use this USB port to charge or supply power to a USB device (e.g. to charge a PDA or a mobile phone or to connect a USB lamp), even if the notebook is switched off. Fujitsu Technology Solutions...
► Left-click on the symbol to remove hardware safely. ► Select the device you wish to shut down and remove. ► Press the "Enter" key. Wait for the dialogue box which tells you that it is now safe to remove the device. Fujitsu Technology Solutions...
When you connect headphones or external loudspeakers, the built-in loudspeakers are disabled. If you purchase a cable from a retailer, please note the following: If you want to connect headphones or a speaker you will need a "3.5 mm jack plug". Fujitsu Technology Solutions...
The equipment and tools you use must be free of static charges. • Remove the power plug from the mains supply before inserting or removing boards containing ESDs. • Always hold boards with ESDs by their edges. • Never touch pins or conductors on boards fitted with ESDs. Fujitsu Technology Solutions...
Otherwise, there is a risk of suffering burns! As some components are exposed that are sensitive to static electricity, please take note of chapter "Notes on installing and removing boards and components", Page Fujitsu Technology Solutions...
Removing memory modules ► Carefully push the two mounting clips outwards (1). Memory expansion Memory module The memory module snaps upwards (2). ► Pull the memory module out of its slot in the direction of the arrow (3). Fujitsu Technology Solutions...
(2). Attaching the cover ► Place the cover into position, following the direction of the arrow (1). ► Fasten the cover in place with the screw (2). ► Complete the memory extension, see "Finishing component removal", Page Fujitsu Technology Solutions...
Keep the screws in a safe place. If you are removing more than one component at the same time, store the screws for the individual components separate from each other. If you install the wrong screws, components may be damaged. ► Lift the cover off the notebook (2). Fujitsu Technology Solutions...
► Lift the hard disk out of the hard disk compartment (2). Installing a hard disk ► Insert the hard disk into the hard disk compartment (1). Ensure that the contacts engage. ► Re-attach the hard disk fixture (2). Fujitsu Technology Solutions...
► Install the battery again (see "Installing a battery", Page 37). ► Turn the notebook the right way up again and place it on a flat surface. ► Reconnect the cables that you disconnected before. Fujitsu Technology Solutions...
► Select the option you want to change with the cursor keys ↑ ↓ ► Press the Enter key. ► Press the key to exit the selected menu. ► For future reference, make a note of the changes you have made (for example, in this manual). Fujitsu Technology Solutions...
► If you want to exit BIOS Setup Utility with these settings, choose Exit Saving Changes and Yes. Save Changes and Power Off ► To save the changes and switch off your device, select Save Changes and Power Off and Yes. The changes are saved. Your device is shut down. Fujitsu Technology Solutions...
PC if you are running processor-intensive gaming software, e.g. games with intensive 3D graphics. Updating your hardware with drivers which have not been approved by Fujitsu Technology Solutions may result in performance losses, data losses or malfunction of the equipment. A list of approved drivers and current BIOS versions can be downloaded from: "http://ts.fujitsu.com/support/downloads.html"...
Hotline/Service Desk. When certain characters are entered on the keyboard, only numerals are written Abeepsounds everysecond Cause Troubleshooting The virtual numeric keypad of your device is ► Press the key. activated, see "Virtual numeric keypad", Page 26 Fujitsu Technology Solutions...
► Check whether the data cable is properly connected to the notebook and the external monitor (if it is plugged in with a connector). ► Switch on the external monitor and the notebook. Fujitsu Technology Solutions...
► Insert a charged battery. ► Connect the mains adapter to the notebook. The power adapter is not connected correctly. ► Check whether the mains adapter is connected correctly to the notebook. ► Switch the notebook on. Fujitsu Technology Solutions...
► Check whether the radio connection is this, the wireless connection to a network does switched on via the software. not work. ► Further information on using the radio component can be found in the help files. Fujitsu Technology Solutions...
► Wait 3 - 5 seconds and switch on the notebook again. If you are using an external keyboard: Keyboard error ► Check the connection and reboot the notebook. ► Make sure that no key is pressed. nn Stuck key Fujitsu Technology Solutions...
Page 91
System battery is dead - Replace and run SETUP service centre. ► Contact your sales outlet or our customer System cache error - Cache disabled service centre. ► Contact your sales outlet or our customer System timer error service centre. Fujitsu Technology Solutions...
Approved memory modules max. 8 GByte DDR3 SO-DIMM per slot The data sheet for the device provides further technical data. You will find the data sheet on your device or on the Internet under "http://ts.fujitsu.com/support". Port replicator (optional) Electrical data...
Technical specifications Rechargeable battery You will find further information about the batteries used in your device on the Internet under "http://ts.fujitsu.com/support". Rated voltage 10.8 V Rated capacity 5200 mAh Mains adapter Technicalspecifications Electrical data Primary Rated voltage 100 V – 240 V (automatic) Rated frequency 50 Hz –...
The "Declarations of Conformity" for the device can be found at our Internet address under: "http://ts.fujitsu.com/ce". Fujitsu Technology Solutions hereby declares that your device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Fujitsu Technology Solutions...
Federal Communications Commission (FCC) of the USA. Although it is not explicitly forbidden to travel in the US trading area carrying this device, to avoid trouble at customs clearance, Fujitsu Technology Solutions GmbH recommends not to bring this device into the US trading area.
Page 96
Places where telephones are specifically installed to alert emergency authorities such as fire, police or medical assistance personnel. • Hospital rooms, residential health care facilities, convalescent homes and prisons. • Hotel, motel or apartment lobbies. • Stores where telephones are used by patrons to order merchandise. Fujitsu Technology Solutions...
Repairs to telecommunication equipment should be made by a Canadian authorised maintenance facility. Any repairs or alterations not expressly approved by Fujitsu or any equipment failures may give the telecommunication company cause to request the user to disconnect the equipment from the telephone line.
Page 98
Les réparations de l’équipement de télécommunications doivent être effectuées par un service de maintenance agréé au Canada. Toute réparation ou modification, qui n’est pas expressément approuvée par Fujitsu, ou toute défaillance de l’équipement peut entraîner la compagnie de télécommunications à exiger que l’utilisateur déconnecte l’équipement de la ligne téléphonique.
In cases in which the policy regarding use of radio devices in specific environments is not clear (e.g., airports, hospitals, chemical/oil/gas industrial plants, private buildings), obtain authorization to use these devices prior to operating the equipment. Fujitsu Technology Solutions...
Page 100
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Modifications not expressly authorised by Fujitsu Technology Solutions may invalidate the user’s right to operate this equipment. Fujitsu Technology Solutions...
Page 102
LCD screen is too dark 83 Notes 13 Life, battery 36 boards 72 Line feed 25 cleaning 16 Loudspeakers 47 disposal / recycling 90 disable 27 energy saving 14 enable 27 LCD screen 34 Safety 13 transport 15 Fujitsu Technology Solutions...
Page 103
Notebooks without radio device 91 Removing a data carrier 40 Removing memory Tab key 25 see Adding memory 73 Technical specifications 88 Return 25 Mains adapter 89 Notebook 88 The radio connection to a network does not work 85 Fujitsu Technology Solutions...
Page 104
Webcam 35 Travel, notebook 15 Weight Saver Troubleshooting 81 Removing 38 Trusted Platform Module 62 Wireless LAN Switching off 50 Switching on 50 Wireless LAN: USB charging function 69 safety notes 13 USB ports 68 User password Fujitsu Technology Solutions...