Related Manuals for Electrolux WA SL3 M
Summary of Contents for Electrolux WA SL3 M
- Page 1 INSTALLATION AND MAINTENANCE WA SL3 M TK SL3 M TA SL3 M WASHING MACHINE 2-15 TUMBLE DRYER 16-34 INDEX...
-
Page 2: Table Of Contents
CONTENTS – WASHING MACHINE SAFETY CHANGING SETTINGS 10–11 Transit screws Language General Locking the programme Child lock on Start/Stop button Wash temperature, C or F Door Changing preset wash temperature Overfill cut-out Child lock Packaging Transport/Winter storage MAINTENANCE 12–13 Scrapping Emptying/cleaning trap and drain pump Inspection holes under drum paddles Cleaning the detergent drawer... -
Page 3: Safety
SAFETY GENERAL TRANSPORT/WINTER STORAGE • Read and keep this manual! If you intend to transport the machine or store • Any electrical work or plumbing must be car- it over winter in unheated premises, empty the ried out by qualified tradesmen. trap and the drain pump, see the chapter on •... -
Page 4: Parts Of The Washing Machine
PARTS OF THE WASHING MACHINE 1. DETERGENT DRAWER 2. POWER SWITCH 3. PROGRAMME PANEL 4. RATING PLATE 5. DOOR-DRAIN PUMP/EMERGENCY OPEN 6. DRAIN PUMP/EMERGENCY OPEN (BEHIND FLAP) 7. DOOR 1. DETERGENT COMPARTMENT – PRE-WASH 2. DETERGENT COMPARTMENT – MAIN WASH 3. - Page 5 EURO PROGRAMMES P1 Heavy wash 90°C P2 Normal wash 60°C P3 Light wash 60°C P4 Normal wash 40°C P5 Synthetic wash 40°C P6 Super quick wash 40°C P7 Wool/hand wash 30°C (1) P8 Spin (1) High water level and gentle motor action. MEDICAL PROGRAMMES P1 Heavy wash 90°C (2)
-
Page 6: Mechanical Installation
MECHANICAL INSTALLATION 3. Finally, refit the rubber spacers to cover the TRANSIT SCREWS Before the machine can be used the three trans- transit holes. it screws must be removed as described below. Each transit screw has a washer and a rubber spacer. -
Page 7: Positioning The Washing Machine
The machine can be anchored to the floor, see POSITIONING THE WASHING MACHINE The washing machine can be built-in or free- enclosed bag containing instructions and parts. standing. It should be positioned so that there is an electrical socket within easy reach. ADJUSTING THE FEET Adjust the feet so that the machine is level and steady on the floor. -
Page 8: Water Intake - Mixed Or Cold Water
first to remove any dirt. Otherwise this could CONNECTING TO THE DRAIN clog the intake filter in the machine and block Machine with drain pump the water supply. The machine is supplied with a drain hose al- ready fitted and this should be connected to a laundry sink, or the like, at a height of 600–900 WATER INTAKE –... -
Page 9: Electrical Installation
ELECTRICAL INSTALLATION ELECTRICAL INSTALLATION CONNECTING TO A COIN MECHANISM The washing machine must be connected using Connection to a coin mechanism must be car- a permanently installed cable through an isola- ried out by a qualified electrician. ting switch by a qualified electrician. A special connecting cable is required to con- nect the machine to a coin mechanism. -
Page 10: Changing Settings
CHANGING SETTINGS button for the fifth time you should hold in the LANGUAGE You can change the language of the displayed programme button for the programme you want text. to lock for 5-10 seconds until the information The languages you can choose from are Dansk, in the display starts flashing. -
Page 11: Child Lock
If you choose C, the wash temperature will Within three seconds of pressing the but- be the same as the intake water temperature. ton for the last time you must then press the button to choose whether you To change the wash temperature, do as follows: want the child lock on or off. -
Page 12: Maintenance
MAINTENANCE EMPTYING/CLEANING TRAP AND DRAIN PUMP INSPECTION HOLES UNDER DRUM PADDLES If you think that an item such as a nail, paper- (only machines with drain pump) The washing machine has a trap that is desig- clip, hair clip or the like has fallen through the ned to catch coins, hair clips, etc. -
Page 13: Inspection Holes Under Drum Paddles
Push the paddle cover away from you until it is CLEANING THE OUTSIDE OF THE MACHINE in its original position. Clean the outside and the programme panel using mild detergent. Do not use abrasives or solvents as they may damage the machine. Do CLEANING THE DETERGENT DRAWER Pull the drawer out as far as it will go. -
Page 14: Troubleshooting
TROUBLESHOOTING • Pull the handle to open the door. DOOR WILL NOT OPEN 1. Check that the power switch is on. 2. Has there been a power cut? Check the fuses in the fuse box. The door cannot be opened with the button if there is no power. -
Page 15: The Display Is Lighting When A Program
– that the drain pump is not blocked by a fo- THE DISPLAY IS LIGHTING WHEN A PROGRAMME reign object. Clean the pump, see chapter on IS SELECTED, BUT NO CHARACTERS OR DIGITS Maintenance. ARE SHOWN – that the drain hose is not kinked. No characters or digits are shown on the dis- After doing this, run programme P8. - Page 16 CONTENTS - TUMBLE DRYER SAFETY CHANGING SETTINGS General Language Using the dryer first time Locking the programme Child lock on Start/Stop buttons Child lock Thermal cut-out Float MAINTENANCE 30–32 Door Cleaning the outside of the machine Packaging Cleaning the fan Scrapping Cleaning the condenser Cleaning the lint filter...
-
Page 17: Safety
SAFETY GENERAL DOOR • Read and keep this manual! The tumble dryer has a magnetic lock, which • Any electrical work must be carried out by a makes it easy to open the door from the outside qualified electrician. or inside. The door is fitted with a switch that automatically switches off the tumble dryer when the door is opened. -
Page 18: Parts Of The Tumble Dryer
PARTS OF THE TUMBLE DRYER 1. LINT FILTER HOLDER 5. DOOR 2. RATING PLATE 6. FAN (BEHIND FRONT PANEL) 3. CONDENSATION WATER TANK – 7. CONDENSER – ONLY CONDENSER TUMBLE CONDENSER TUMBLE DRYERS ONLY DRYERS (BEHIND FRONT PANEL) 4. PANEL 8. -
Page 19: Technical Information
TECHNICAL INFORMATION TECHNICAL DATA Height: 850 mm. Width: 595 mm. Depth: 585 mm. Weight: 39 kg (vented) / 47 kg (condenser). Drum capacity: 111 l. Drying capacity: 6.0 kg. Speed: 52 rpm. Power rating: See rating plate. Composition of drum: Stainless steel. -
Page 20: Mechanical Installation
The dimensions of the tum- C. Stacked The tumble dryer can be stacked on top of an ble dryer are: Electrolux Wascator WE 50 washing machine. Use the stacking kit that is supplied with the machine: 2 plastic holders. Plastic bag inside the drum. -
Page 21: Adjusting The Feet
Fit the stacking kit as follows: 4. Position the plastic cups so that the arrowed lugs 1. Unscrew the two arrowed screws at the rear of the are flush with the front washing machine. and side of the top, then press down onto the top. -
Page 22: Condensed Water
CONDENSED WATER Connect the vent hose as follows: 1. Slide the vent hose over the end of the adap- (only applies to condenser tumble dryer) The machine is supplied with a 2.0 metre-long ter and secure with the plastic strap. drain hose. -
Page 23: Reversing The Door
If there is only one vent duct from the room Installation in warm climates When installing in temperatures above 25°C then a vent spacer must be fitted, article num- (77°F) with a high level of humidity, do not ber 92 059 01. route the air exhaust hose upwards. - Page 24 2. Pull the bottom edge of the door outwards 6. Unscrew the two screws from the edges of while twisting the hinge bracket in the direc- the door about five millimetres so that you can tion shown by remove the door magnet and plate from the the arrows.
- Page 25 10. Screw in the screws to secure the door mag- 13. Fit the hinge bracket, tightening the screws net and plate. in the order shown. 11. Unscrew the arrowed screw. If the dryer is a con- denser model you must also open the cover over the con- denser.
-
Page 26: Electrical Installation
ELECTRICAL INSTALLATION ELECTRICAL INSTALLATION Connecting the tumble dryer and washing The washing machine must be connected using machine together a permanently installed cable through an isola- Wiring the two machines together as described ting switch by a qualified electrician. below must be carried out by a qualified elec- trician. - Page 27 ELECTRICAL INSTALLATION TUMBLE DRYER...
-
Page 28: Changing Settings
CHANGING SETTINGS button for the fifth time you should hold in the LANGUAGE You can change the language of the displayed programme button for the programme you want text. to lock for 5-10 seconds until the information The languages you can choose from are Dansk, in the display starts flashing. -
Page 30: Maintenance
MAINTENANCE 4. Hold the fan and unscrew the nut. CLEANING THE OUTSIDE OF THE MACHINE Clean the outside and the programme panel using mild detergent. Do not use abrasives or solvents as they may damage the machine. Do not spray the machine with water. NOTE! Do not let dust collect around the machine. -
Page 31: Cleaning The Condenser
5. Refit the condenser. Make sure you put it in CLEANING THE CONDENSER The condenser should be cleaned at least six the right way times a year, or more often if the user has pets. up. The top of the con- 1. -
Page 32: Cleaning The Lint Filter
IN AREAS WITH HARD WATER CLEANING THE LINT FILTER HOLDER If the machine is installed in an area that has Dust and dirt can gather in the bottom of the hard water this can produce a limescale deposit lint filter holder. Take out the lint filter and use on the lint filter. -
Page 33: Troubleshooting
TROUBLESHOOTING MACHINE WILL NOT START NOTE: Check If your dryer overheats frequently, it may not be • that the door is closed properly. vented properly or the room in which it is loca- • if the child lock is activated. To start the tum- ted may not have sufficient air circulation. -
Page 34: The Display Is Lighting When A Program
Maximum programme duration. After the To change language do as follows: machine has run for the maximum time (3 Switch off the power switch, , then switch it hours) it automatically stops. Check and repla- on again so that the machine is in start-up mode. ce any blown fuses in the fuse box. - Page 35 SERVICE SERVICESTELLEN POINTS DE SERVICE SERVIZIO DOPO VENDITA 1028 Préverenges 6916 Grancia Zürich/Mägenwil Zona Industriale E Le Trési 6 5506 Mägenwil Industriestr. 10 1950 Sion 9000 St. Gallen Rue de la Piscine Vonwilstrasse 15 4127 Birsfelden Hauptstrasse 52 8604 Volketswil Hözliwiesenstrasse 12 6032 Emmen Buholzstrasse 1...
- Page 36 INDEX WASHING MACHINE Page Page Page Hard water Rating plate Adjustable feet Hardness of water Safety precautions Centigrade or Fahrenheit 1 0 Imbalance sensor Scrapping Changing preset wash Inspection holes temperature Technical data Installation, electrical Child lock Transport Installation, mechanical Cleaning Transit screws Coin mechanism...