LE10 Radio Receiver Table of Contents | en Table of Contents Safety instructions General safety instructions Environmental conditions Electrostatic Discharge (ESD) Product information General description Compatible transmitters Main applications Description of the different modes Installation Unpacking Connecting the power supply 3.2.1...
| Table of Contents LE10 Radio Receiver Normal mode (modes 1 and 2) 6.2.1 Activation of a transmitter in normal mode Dementia (mode 3) 6.3.1 Activation of a MIYS37L Wristband Transmitter 6.3.2 Detection of a MIYS37E Wristband Transmitter alone 6.3.3...
Installation and initial operation should only be carried out by trained service personnel. Environmental conditions The LE10 Radio Receiver must not be located near a water tap or any other source of water. The electrical safety of the LE10 Radio Receiver is only guaranteed if the electrical installation is in accordance with the national regulations and if this installation works properly.
Bosch radio transmitters at the frequency of 434.01 MHz. After receiving radio signals from either programmed or not programmed wireless transmitters, the LE10 Radio Receiver reacts by activating its two green and red LEDs and by switching relay outputs of two relays. LED 1 (green) LED 2 (red) Figure 2.1 Front view of the LE10 Radio Receiver...
LE10 Radio Receiver as part of a Resident Alert System monitoring dementia After receiving a signal from a dementia transmitter, the relay will be activated to close a monitored door.
Page 8
| Product information LE10 Radio Receiver Mode Name Description Dementia with This mode allows to connect the LE10 Radio Accompany Receiver to a wired emergency call system, in which the Accompany function can be implemented. It will wait 10 seconds after receiving a signal from a MIYS37L transmitter.
LE10 Radio Receiver. Contact immediately your local representative. 1. Take all components out of the box and place the LE10 Radio Receiver on the working space. 2. Check that the following accessories are delivered: the fixings (2 screws and 2 screw anchors) and this user manual.
| Installation LE10 Radio Receiver Wall installation You can fasten the LE10 Radio Receiver on a smooth wall surface using two screws. Installation cables should be placed inside the cable channels on the bottom. 3.4 in (80 mm) 2.2 in (53.8 mm) 0.51 in...
Connection compartment Connecting ports To open the device: – hold the LE10 Radio Receiver in one hand, facing you, so that you can see the Bosch logo and the two LEDs. – grab the connection compartment housing with the other hand and slide it towards you.
4.2.1 Mode indication after power on – When the power supply is connected to the LE10 Radio Receiver, the green LED will light up permanently for 2 seconds. Afterwards, the device will display the current mode through the green LED, by blinking as many times as the number of the mode.
LE10 Radio Receiver Programming | en Programming Enter programming mode To enter programming mode, press simply button T1 for the desired time. See Section 4.1 Connecting ports, page 11. NOTICE! Both relays will not be activated in the programming mode.
This indication confirms that all transmitters are then deleted. NOTICE! If button T1 is pressed longer than 40 seconds, then the LE10 Radio Receiver will jump out of the programming mode. F.01U.278.517 | V2.0 | 2012.11...
A door address must be stored beforehand in a MIYS37L Wristband Transmitter with Locating function. NOTICE! Only one door address of a MIYS37L Wristband Transmitter with Locating function can be matched in the LE10 Radio Receiver. To start programming –...
| Operation LE10 Radio Receiver Operation Standby mode The LE10 Radio Receiver enters standby mode when the power supply is connected. Both relays are off. See Section 4.2.1 Mode indication after power on, page 12. 6.1.1 Standby with no transmitter programmed Device behavior –...
LE10 Radio Receiver Operation | en – Relay 2 switches on permanently until the battery is replaced and the transmitter is activated again. NOTICE! In normal mode 2, the red LED is deactivated regarding battery- low indication and will not blink every 10 seconds.
| Operation LE10 Radio Receiver 6.3.2 Detection of a MIYS37E Wristband Transmitter alone Device behavior – The green LED stays permanently on. When a MIYS37E transmitter is detected: – The red LED lights up permanently for 30 seconds. –...
LE10 Radio Receiver Operation | en Dementia with Accompany (mode 4) 6.4.1 Activation of a MIYS37L Wristband Transmitter Device behavior – The green LED stays permanently on. When a MIYS37L transmitter is activated, a 10-second time slot starts. If, during these 10 seconds, a MIYS37E transmitter is detected: –...
| Operation LE10 Radio Receiver 6.5.2 Activation of a programmed transmitter with a battery-low message or with a new battery The behavior of the device is the same as in Section 6.2.1 Activation of a transmitter in normal mode, page 16.
LE10 Radio Receiver Operation | en 6.7.2 Reset of a battery-low indication with button T1 Device behavior – The green LED stays permanently on. – The red LED is already blinking every 10 seconds. Upon pressing button T1 min. 1 second, there is a reset of the battery-low indication: –...
LE10 Radio Receiver NOTICE! A MIYN46 transmitter in repeated alarm mode extends the behavior of the LE10 by approximately 26 minutes. If several MIYN46 transmitters are programmed, each activated transmitter stops the sequence and starts its own sequence. Battery-low indication: –...
LE10 Radio Receiver Technical data | en Technical data Dimensions 5.3 x 3.2 x 1.0 inches (133 x 82 x 26 mm) Weight 3.9 oz (110 g) Material Color Top: white, similar to RAL 9010 Bottom: charcoal External power supply...