Table of Contents
Advertisement
I Make sure to enable the HDMI CEC when making HDMI connection.
For details, refer to the operation
manual I
]
of the TV. (HT-SL77)
1
Plug the AC power cord
into a AC outlet, the stand-by
indicator turns RED.
The Amplifier will automatically
power on if:
DIGITAL (HDMI) function: TV or similar component
which
supports HDMI CEC, is turned on. (HT-SL77 only)
ANALOG
function:
Audio signal is detected
from Audio
input.
The Amplifier stand-by indicator will turn BLUE if TV signal
is detected.
Notes:
•
Make sure to select function (refer Input Selector) for a
preferred connection.
•
A slight audio
delay after TV is turned ON does not
mean that the system is faulty. This is normal.
•
"AQUOS
speaker
is
enabled"
message
will
be
displayed
if SHARP LCD TV does not detect HT-SL77
during power on. However the message "AQUOS audio
with AQUOS LINK is enabled" will be displayed soon as
HT-SL77 is detected.
These
messages
may vary for
other TV model.
The
Amplifier
and
Subwoofer
will
link
automatically
(wirelessly)
when turned on as it is already
pre-linked
at
the factory. If the link cannot be established,
please set the
connection
by the following method.
1. Press and hold the PAIRING button on the Amplifier for
more than 3 seconds.
2. Within 2 minutes, press and hold the PAIRING button on
the Subwoofer for more than 3 seconds
•
During pairing process,
the Amplifier
and Subwoofer
indicator will blink in BLUE for a few seconds.
•
The Amplifier and Subwoofer will be linked (connected)
if both unit indicators turn BLUE.
Notes:
•
If a device such as microwave oven, wireless
LAN card,
Bluetooth
device
or any other
device
that uses the
same 2.4GHz frequency
near the system, some sound
interruption
may be heard due to interference.
•
The
transmission
distance
of the
wireless
signal
between the Subwoofer
and Amplifier
is about 32 feet
(10m),
but may vary
depending
on your
operating
environment.
If a steel-concrete
or metallic
wall
is
between
the Subwoofer
and the Amplifier, the system
may not operate
at all, because
the wireless
signal
cannot penetrate metal.
Caution:
•
Keep the Subwoofer
away from water and moisture.
•
To get the optimum
listening performance,
make sure
the area around the Sound Bar and Subwoofer
is clear
of any obstacles.
Turn the INPUT switch
on the Amplifier
to select
the
function mode.
DIGITAL: Select when using Digital (HDMI) connection.
ANALOG: Select when using Analog (Audio In) connection.
The Audio Return Channel (ARC) enables an HDMI ARC-
capable TV to send the audio stream to the HDMI OUT
terminal of the receiver. To use this function, your TV must
support the ARC. Make sure the TV Audio output setting is
set to PCM, not other formats such as Dolby Digital, DTS,
etc. For details, refer to the operation manual of the TV.
Subwoofer
DIGITAL (HDMI) function:
Volume can only be controlled
from your TV via HDMI CEC. (HT-SL77 only)
ANALOG
function:
Turn GAIN (AUDIO
IN) knob toward
MAX./MIN.
to increase or decrease
the volume.
Note:
Power/Pairing
indicators
status.
Power/Pairing
Indicator
Turns BLUE
Blinks in BLUE
quickly
Turns RED
Condition
Amplifier
Subwoofer
Power On
Power On
(linked)
(linked)
Pairing in
Pairing in
progress
progress
Stand-by
Stand-by
This unit will automatically
go to stand-by mode (both unit
indicators
turns RED) if:
DIGITAL (HDMI) function:
TV or similar component
which
supports HDMI CEC, is turned off. (HT-SL77 only)
ANALOG function:
No signal from Audio input is detected
after 20 minutes.
This switch enables you to control the Subwoofer
bass
output.
Turn
the
"BASS
LEVEU'
switch
at the
back
of the
Subwoofer
to HIGH or LOW to adjust the output level.
•..... ill
- Quick Links:
- Recommended Connection
Hide quick links:
Advertisement
Table of Contents
