Hitachi ED-D11N User Manual
  1. Manuals
  2. Brands
  3. Hitachi Manuals
  4. Projector
  5. ED-D11N
  6. User manual
Hitachi ED-D11N User Manual

Hitachi ED-D11N User Manual

Hide thumbs Also See for ED-D11N:
Table of Contents

Advertisement

Quick Links

Projector
ED-D10N/ED-D11N
User's Manual (detailed)
Operating Guide
Thank you for purchasing this projector.
WARNING
WARNING
CAUTION
NOTICE
NOTE
Trademark acknowledgment
®
®
Safety Guide
1

Advertisement

Table of Contents
loading

Related Manuals for Hitachi ED-D11N

Summary of Contents for Hitachi ED-D11N

  • Page 1 Projector ED-D10N/ED-D11N User's Manual (detailed) Operating Guide Thank you for purchasing this projector. WARNING Safety Guide WARNING CAUTION NOTICE NOTE Trademark acknowledgment ® ®...
  • Page 2 Read this Safety Guide first. Projector User's Manual - Safety Guide Thank you for purchasing this projector. WARNING • Before using, read these user's manuals of this projector to ensure correct usage through understanding. After reading, store them in a safe place for future reference.

  • Page 3: Safety Precautions

    Safety Precautions WARNING Never use the projector if a problem should occur. Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. can cause a fire or electrical shock. In such case, immediately turn off the power switch and then disconnect the power plug from the power outlet.
  • Page 4 Safety Precautions (continued) WARNING Be cautious of High temperatures of the projector. High temperatures are generated when the lamp is lit. It could result in fire or burn. Use special caution in households where children are present. Do not touch about the lens, air fans and ventilation openings during use or immediately after use, to prevent a burn.
  • Page 5 Safety Precautions (continued) WARNING Be careful in handling the light source lamp. The projector uses a high-pressure mercury glass lamp made of glass. The lamp can break with a loud bang, or burn out. When the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.
  • Page 6 Safety Precautions (continued) CAUTION Be careful in moving the projector. Neglect could result in an injury or damage. • Do not move the projector during use. Before moving, disconnect the power cord and all external connections, and close the slide lens door or attach the lens cap.
  • Page 7 Safety Precautions (continued) CAUTION Remove the power cord for complete separation. • For safety purposes, disconnect the power cord if the projector is not to be used for prolonged periods of time. Disconnect the • Before cleaning, turn off and unplug the projector. Neglect could result in plug from the fire or electrical shock.
  • Page 8 Safety Precautions (continued) NOTE About consumables. Lamp, LCD panels, polarizors and other optical components, and air filter and cooling fans have a different lifetime in each. These parts may need to be replaced after a long usage time. • This product isn’t designed for continuous use of long time. In the case of continuous use for 6 hours or more, or use for 6 hours or more every day (even if it isn’t continuous), or repetitious use, the lifetime may be shortened, and these parts may need to be replaced even if one year has not passed since the beginning of using.
  • Page 9 Lamp WARNING HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
  • Page 10 Regulatory Notices FCC Statement Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

  • Page 11: Table Of Contents

    Contents About this manual... 1 OLOR TEMP OLOR HARPNESS Y MEMORY Contents ....2 IMAGE menu .

  • Page 12: Projector Features

    Projector features / Preparations Checking the contents of package MY SOURCE/ VIDEO COMPUTER DOC.CAMERA ASPECT AUTO SEARCH BLANK MAGNIFY FREEZE PAGE VOLUME DOWN KEYSTONE MY BUTTON MUTE POSITION MENU ENTER RESET NOTE...

  • Page 13: Preparations

    Projector features / Preparations Fastening the lens cover CAUTION...

  • Page 14: Part Names

    Part names HOT! Projector (10) (16) (15) AC IN (13) (12) (14) (11) HOT! (17) WARNING HOT! CAUTION...
  • Page 15 Part names Control panel STANDBY/ON 18, 25) INPUT STANDBY/ON INPUT MENU LAMP MENU TEMP 14, 17, 73) POWER POWER TEMP LAMP Rear panel AUDIO IN1 VIDEO AUDIO IN2 S-VIDEO COMPUTER IN1 AUDIO IN3 (R, L) COMPUTER IN2 AUDIO OUT (R, L) MONITOR OUT HDMI CONTROL...

  • Page 16: Remote Control

    Part names Remote control VIDEO (10) COMPUTER SEARCH MY SOURCE/ COMPUTER VIDEO DOC.CAMERA STANDBY/ON AUTO ASPECT SEARCH BLANK (16) (12) ASPECT PAGE VOLUME MAGNIFY FREEZE (14) AUTO DOWN (11) BLANK KEYSTONE MY BUTTON MUTE (19) (13) MAGNIFY - ON (17) (15) 16, 23) (20)
  • Page 17 Setting up Arrangement Screen size (diagonal) Projection distance Screen height Screen height inch inch inch type(inch)
  • Page 18 Setting up Arrangement (continued) WARNING CAUTION NOTE...
  • Page 19 Setting up Connecting your devices Monitor AUDIO OUT RGB OUT AUDIO OUT RGB OUT RS-232C RGB IN HDMI Speakers (with an VIDEO OUT HDMI S-VIDEO OUT AUDIO OUT AUDIO OUT AUDIO OUT COMPONENT VIDEO OUT AUDIO IN VCR/DVD/Blu-ray Disc player Projector Ferrite core for s-video cable S-VIDEO OUT...
  • Page 20 Setting up Connecting your devices (continued) External device RS-232C HDMI WARNING CAUTION NOTICE NOTE COMPUTER IN1/2...
  • Page 21 Setting up Connecting your devices (continued) NOTE HDMI...
  • Page 22 Setting up Connecting your devices (continued) About Plug-and-Play capability COMPUTER IN1 NOTE for HDMI HDMI User's Manual(detailed) - Technical HDMI...
  • Page 23 Setting up Connecting power supply AC IN POWER AC IN WARNING Using the security bar and slot WARNING CAUTION NOTE...
  • Page 24 Remote control Installing the batteries (HITACHI MAXELL, Part No. LR6 or R6P) WARNING About the remote control signal 30º 30º NOTE...

  • Page 25: Remote Control

    Remote control Changing the frequency of remote control signal MY SOURCE/ VIDEO COMPUTER DOC.CAMERA AUTO ASPECT SEARCH BLANK MAGNIFY FREEZE PAGE VOLUME DOWN KEYSTONE MY BUTTON MUTE MENU POSITION ENTER VOLUME - RESET RESET MAGNIFY OFF...

  • Page 26: Power On/Off

    Power on/off STANDBY/ON Turning on the power POWER STANDBY/ON INPUT MENU LAMP TEMP POWER POWER MY SOURCE/ VIDEO COMPUTER DOC.CAMERA ASPECT AUTO SEARCH BLANK FREEZE PAGE VOLUME MAGNIFY STANDBY/ON DOWN KEYSTONE MY BUTTON MUTE POSITION MENU ENTER POWER RESET Turning off the power STANDBY/ON STANDBY/ON POWER...

  • Page 27: Operating

    Operating VOLUME + - Adjusting the volume VOLUME +/- MY SOURCE/ VIDEO COMPUTER DOC.CAMERA ASPECT AUTO SEARCH BLANK MAGNIFY FREEZE PAGE VOLUME DOWN KEYSTONE MY BUTTON MUTE MENU POSITION Temporarily muting the sound MUTE MUTE MY SOURCE/ VIDEO COMPUTER DOC.CAMERA ASPECT AUTO SEARCH...
  • Page 28 Operating Selecting an input signal (continued) COMPUTER COMPUTER MY SOURCE/ VIDEO COMPUTER DOC.CAMERA ASPECT AUTO SEARCH BLANK MAGNIFY FREEZE PAGE VOLUME DOWN KEYSTONE MY BUTTON MUTE MENU POSITION COMPUTER VIDEO S-VIDEO COMPUTER IN1 VIDEO VIDEO MY SOURCE/ COMPUTER VIDEO DOC.CAMERA ASPECT AUTO SEARCH...

  • Page 29: Selecting An Aspect Ratio

    Operating Searching an input signal SEARCH SEARCH MY SOURCE/ VIDEO COMPUTER DOC.CAMERA ASPECT AUTO SEARCH BLANK MAGNIFY FREEZE PAGE VOLUME DOWN KEYSTONE MY BUTTON MUTE MENU POSITION Selecting an aspect ratio ASPECT ASPECT MY SOURCE/ VIDEO COMPUTER DOC.CAMERA ASPECT AUTO SEARCH BLANK For a computer signal...
  • Page 30 Operating Adjusting the projector's elevator 3° CAUTION Adjusting the focus...

  • Page 31: Using The Automatic Adjustment Feature

    Operating Using the automatic adjustment feature AUTO AUTO MY SOURCE/ VIDEO COMPUTER DOC.CAMERA For a computer signal ASPECT AUTO SEARCH BLANK MAGNIFY FREEZE PAGE VOLUME DOWN KEYSTONE MY BUTTON MUTE POSITION MENU For a video signal and s-video signal For a component video signal Adjusting the position KEYSTONE MY BUTTON...

  • Page 32: Correcting The Keystone Distortions

    Operating KEYSTONE Correcting the keystone distortions ASPECT AUTO SEARCH BLANK KEYSTONE MAGNIFY FREEZE PAGE VOLUME DOWN KEYSTONE MY BUTTON MUTE KEYSTONE Using the magnify feature MAGNIFY ON/OFF MAGNIFY ON MAGNIFY ON MY SOURCE/ COMPUTER VIDEO DOC.CAMERA ASPECT AUTO SEARCH BLANK MAGNIFY FREEZE PAGE...
  • Page 33 Operating Temporarily freezing the screen FREEZE FREEZE MY SOURCE/ VIDEO COMPUTER DOC.CAMERA ASPECT AUTO SEARCH BLANK MAGNIFY FREEZE PAGE VOLUME DOWN KEYSTONE MY BUTTON MUTE FREEZE Temporarily blanking the screen BLANK BLANK MY SOURCE/ VIDEO COMPUTER DOC.CAMERA AUTO ASPECT SEARCH BLANK MAGNIFY FREEZE...

  • Page 34: Using The Menu Function

    Operating Using the menu function MENU INPUT ENTER MENU INPUT MENU STANDBY/ON LAMP MENU POSITION TEMP MY SOURCE/ VIDEO COMPUTER DOC.CAMERA AUTO ASPECT SEARCH BLANK MAGNIFY FREEZE PAGE VOLUME DOWN POWER ENTER KEYSTONE MY BUTTON MUTE POSITION MENU ENTER RESET RESET MENU RESET...
  • Page 35 Operating Using the menu function (continued) MENU ENTER POSITION RESET Indication in OSD (On Screen Display) Indication Meaning MENU...

  • Page 36: Easy Menu

    EASY MENU Item Description ASPECT D-ZOOM KEYSTONE PICTURE MODE 29, 30...
  • Page 37 EASY MENU Item Description ECO MODE MIRROR RESET FILTER TIME LANGUAGE ENTER ADVANCED MENU EXIT ENTER...

  • Page 38: Picture Menu

    PICTURE menu ENTER Item Description BRIGHTNESS CONTRAST 1 DEFAULT 1 CUSTOM 2 DEFAULT 2 CUSTOM 3 DEFAULT 6 CUSTOM 3 CUSTOM 6 DEFAULT 5 CUSTOM 5 DEFAULT 4 CUSTOM 4 DEFAULT To adjust CUSTOM ENTER GAMMA ENTER INPUT ENTER INPUT)

  • Page 39: Color Temp , C M Y Memory

    PICTURE menu Item Description 1 HIGH 1 CUSTOM 2 MID 2 CUSTOM 6 CUSTOM 3 LOW 6 Hi-BRIGHT-3 3 CUSTOM 5 CUSTOM 5 Hi-BRIGHT-2 4 CUSTOM 4 Hi-BRIGHT-1 To adjust CUSTOM ENTER COLOR TEMP ENTER INPUT) ENTER INPUT) COLOR...
  • Page 40 PICTURE menu Item Description TINT SHARPNESS ENTER MY MEMORY MY BUTTON...

  • Page 41: Image Menu

    IMAGE menu ENTER Item Description For a computer signal For an HDMI signal For a video signal, s-video signal or component video signal ASPECT For no signal OVER SCAN RESET V POSITION above...
  • Page 42 IMAGE menu Item Description RESET H POSITION H PHASE H SIZE RESET For a computer signal For a video signal and s-video signal AUTO ADJUST EXECUTE For a component video signal...

  • Page 43: Input Menu

    INPUT menu ENTER Item Description PROGRESSIVE VIDEO NR COLOR SPACE...

  • Page 44: Video Format , H

    INPUT menu Item Description S-VIDEO VIDEO VIDEO FORMAT VIDEO S-VIDEO HDMI HDMI FORMAT HDMI HDMI RANGE...

  • Page 45: Computer In , F

    INPUT menu Item Description COMPUTER IN1 COMPUTER IN COMPUTER IN COMPUTER IN1/2 FRAME LOCK...
  • Page 46 INPUT menu Item Description COMPUTER IN1 COMPUTER IN2 ENTER RESOLUTION ENTER ENTER...

  • Page 47: Setup Menu

    SETUP menu ENTER Item Description D-ZOOM D-SHIFT V D-SHIFT H PICTURE POSITION KEYSTONE ECO MODE...

  • Page 48: Monitor Out

    SETUP menu Item Description MIRROR STANDBY MODE below MONITOR OUT AUDIO OUT MONITOR OUT MONITOR OUT MONITOR OUT above MONITOR OUT COMPUTER IN MONITOR OUT...

  • Page 49: Audio Menu

    AUDIO menu ENTER Item Description VOLUME SPEAKER AUDIO ENTER AUDIO IN AUDIO SOURCE HDMI HDMI VIDEO S-VIDEO COMPUTER IN1 COMPUTER HDMI AUDIO...

  • Page 50: Screen Menu

    SCREEN menu ENTER Item Description LANGUAGE ENTER INPUT MENU POSITION MENU BLANK BLANK START UP...
  • Page 51 SCREEN menu Item Description ENTER INPUT RESET INPUT MyScreen ENTER INPUT) RESET INPUT...
  • Page 52 SCREEN menu Item Description MyScreen Lock MESSAGE FREEZE...
  • Page 53 SCREEN menu Item Description ENTER ENTER INPUT) RESET INPUT SOURCE NAME ENTER INPUT ENTER INPUT ENTER INPUT ENTER INPUT...
  • Page 54 SCREEN menu Item Description ENTER MY BUTTON TEMPLATE RESET ENTER INPUT ENTER INPUT ENTER INPUT...
  • Page 55 SCREEN menu Item Description DISPLAY C.C. (Closed Caption) MODE CHANNEL...

  • Page 56: Option Menu

    OPTION menu ENTER Item Description AUTO SEARCH DIRECT POWER ON...

  • Page 57: Uto Power Off

    OPTION menu Item Description AUTO POWER OFF CONTROL ENTER RESET LAMP TIME 66,67) ENTER RESET FILTER TIME...
  • Page 58 OPTION menu Item Description BUTTON 1/2 ENTER ENTER INPUT COMPUTER IN1 COMPUTER IN2 HDMI S-VIDEO VIDEO Messenger Function of the User's Manual - Network Guide MY BUTTON MY BUTTON MY SOURCE/DOC.CAMERA MY SOURCE...
  • Page 59 OPTION menu Item Description ENTER FAN SPEED AUTO ADJUST SERVICE GHOST FILTER MESSAGE...
  • Page 60 OPTION menu Item Description KEY LOCK STANDBY/ON REMOTE FREQ. SERVICE (continued) CONTROL COMMUNICATION the User's Manual - Network Guide...
  • Page 61 OPTION menu Item Description COMMUNICATION TYPE CONTROL CONTROL Controlling the external device via the projector (using the NETWORK BRIDGE function) of the User’s Manual - Network Guide) CONTROL below) SERIAL SETTINGS CONTROL BAUD RATE SERVICE COMMUNICATION (continued) (continued) PARITY above) TRANSMISSION METHOD CONTROL...
  • Page 62 OPTION menu Item Description RESPONSE LIMIT TIME CONTROL CONTROL SERVICE COMMUNICATION (continued) (continued) BYTES INTERVAL TIMEOUT CONTROL...
  • Page 63 OPTION menu Item Description INFORMATION SERVICE (continued) FACTORY RESET...

  • Page 64: Network Menu

    NETWORK menu ENTER the User’s Manual - Network Guide NOTE Date/Time Settings of the User’s Manual - Network Guide) Item Description ENTER SETUP DHCP (Dynamic Host Protocol)
  • Page 65 NETWORK menu Item Description IP ADDRESS SUBNET MASK DEFAULT GATEWAY SETUP DNS SERVER TIME DIFFERENCE DATE AND TIME Date/Time Settings of the User’s Manual - Network Guide)

  • Page 66: Rojector Name

    NETWORK menu Item Description ENTER INPUT RESET INPUT ENTER INPUT PROJECTOR NAME ENTER INPUT ENTER INPUT ENTER INPUT...
  • Page 67 NETWORK menu Item Description MY IMAGE (Still Image Transfer) Display of the User’s Manual - Network Guide) ENTER MY IMAGE To switch the image displayed To return to the menu RESET AMX D.D. (AMX Device Discovery)
  • Page 68 NETWORK menu Item Description INFORMATION SERVICE...

  • Page 69: Security Menu

    SECURITY menu Enter the SECURITY menu ENTER 5010 below ENTER If you have forgotten your password RESET INPUT Item Description ENTER ENTER SECURITY PASSWORD CHANGE ENTER ENTER...
  • Page 70 SECURITY menu Item Description 1 Turning on the MyScreen PASSWORD ENTER ENTER ENTER ENTER MyScreen PASSWORD 2 Turning off the MyScreen PASSWORD 3 If you have forgotten your password...
  • Page 71 SECURITY menu Item Description 1 Turning on the PIN LOCK ENTER COMPUTER INPUT PIN LOCK 2 Turning off the PIN LOCK 3 If you have forgotten your PIN Code RESET INPUT...
  • Page 72 SECURITY menu Item Description 1 Turning on the TRANSITION DETECTOR ENTER ENTER TRANSITION DETECTOR ENTER ENTER 2 Turning off the TRANSITION DETECTOR 3 If you have forgotten your password...
  • Page 73 SECURITY menu Item Description 1 Turning on the MY TEXT PASSWORD ENTER ENTER MY TEXT PASSWORD ENTER ENTER 2 Turning off the MY TEXT PASSWORD 3 If you have forgotten your password...

  • Page 74: Y Text Display

    SECURITY menu Item Description ENTER MY TEXT DISPLAY ENTER ENTER INPUT RESET INPUT ENTER INPUT MY TEXT WRITING ENTER INPUT ENTER INPUT ENTER INPUT...

  • Page 75: Maintenance

    Maintenance Replacing the lamp Type number : DT01091 Replacing the lamp In case of replacement by yourself, follow the following procedure. Never MENU ENTER ENTER ENTER RESET CAUTION NOTE...
  • Page 76 Maintenance Replacing the lamp (continued) Lamp warning HIGH TEMPERATURE HIGH PRESSURE HIGH VOLTAGE WARNING About disposal of a lamp:...
  • Page 77 Maintenance Type number : UX35971 MENU ENTER RESET ” WARNING NOTE...
  • Page 78 Maintenance Replacing the internal clock battery OPEN OPEN CLOSE HITACHI MAXELL CR2032 CR2032H CLOSE WARNING...

  • Page 79: Other Care

    Maintenance Other care Inside of the projector Caring for the lens Caring for the cabinet and remote control WARNING CAUTION...
  • Page 80 Troubleshooting WARNING...
  • Page 81 Troubleshooting Related messages Message Description There is no input signal. The horizontal or vertical frequency of the input signal An improper signal is input. The interior temperature is too high, or has increased or decreased in a short term. The button operation is not available (...

  • Page 82: Regarding The Indicator Lamps

    Troubleshooting Regarding the indicator lamps POWER TEMP LAMP Description POWER TEMP LAMP The projector is in a standby state. Orange Blinking The projector is warming up. Green The projector is in an on state. Green Blinking The projector is cooling down. Orange The projector is cooling down.

  • Page 83: Troubleshooting

    Troubleshooting Regarding the indicator lamps (continued) Description POWER TEMP LAMP The cooling fan is not operating. Blinking Blinking There is a possibility that the interior portion has become heated. Blinking blinking in Green There is a possibility that the interior portion has become overcooled.

  • Page 84: Shutting The Projector Down

    Troubleshooting Shutting the projector down Resetting all settings Phenomena that may be easy to be mistaken for machine defects Reference Phenomenon Cases not involving a machine defect page The electrical power cord is not plugged in. The main power source has been interrupted during operation such as by a power outage (blackout), etc.
  • Page 85 Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Reference Phenomenon Cases not involving a machine defect page The signal cables are not correctly connected. The MUTE function is working. MUTE VOLUME + - The volume is adjusted to an extremely low level. The AUDIO SOURCE/SPEAKER setting is not correct.
  • Page 86 Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Reference Phenomenon Cases not involving a machine defect page The HDMI cable is not correctly connected. Your HDMI equipment is not compatible with the projector. Your HDMI equipment and the projector are not HDMI harmonized.
  • Page 87 Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Reference Phenomenon Cases not involving a machine defect page Vertical resolution of the input signal is equal to or more than the vertical resolution of display area that is determined by D-ZOOM adjustment value.
  • Page 88 Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Reference Phenomenon Cases not involving a machine defect page The lamp is turned off. STANDBY ON POWER TEMP LAMP Security features are activated and the projector is locked.
  • Page 89 Item Computer input port Computer output port Video input port HDMI input port Audio input/output port Others Lamp Filter set Mounting accessary Laser remote control Cable cover...
  • Page 91 Projector ED-D10N/ED-D11N User's Manual (concise) Thank you for purchasing this projector. Please read through this manual before using this product, in order to use safely and utilize well the product. WARNING ►Before using this product, be sure to read all manuals for this product.

  • Page 92: First Of All

    First of all Entries and graphical symbols explanation The following entries and graphical symbols are used for the manuals and the product as follows, for safety purpose. Please know their meanings beforehand, and heed them. WARNING This entry warns of a risk of serious personal injury or even death. CAUTION This entry warns of a risk of personal injury or physical damage.

  • Page 93: Regulatory Notices

    ED-D10N, ED-D11N Responsible Party Hitachi America, Ltd. Address 900 Hitachi way, Chula Vista, CA 91914-3556 U.S.A. Telephone Number +1 -800-225-1741 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has...

  • Page 94: About Waste Electrical And Electronic Equipment

    Regulatory notices (continued) About Waste Electrical and Electronic Equipment The mark is in compliance with the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE). The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries or accumulators as unsorted municipal waste, but use the return and collection systems available.

  • Page 95: Contents Of Package

    Holding the hook part of the battery cover, remove it. Align and insert the two AA batteries HITACHI MAXELL, Part No.LR6 or R6P according to their plus and minus terminals as indicated in the remote control. Replace the battery cover in the direction of the arrow and snap it back into place.

  • Page 96: Arrangement

    Arrangement Refer to the illustrations and tables below to determine screen size and projection distance. The values shown in the table are calculated for a full size screen: 1024 x 768 Screen size (diagonal) Projection distance (±8%) Screen height • On a horizontal surface Screen size (diagonal) Projection distance...

  • Page 97: Connecting Your Devices

    Connecting your devices Be sure to read the manuals for devices before connecting them to the projector. Make sure that all the devices are suitable to be connected with this product, and prepare the cables required to connect. Please refer to the following illustrations to connect them.
  • Page 98 Connecting your devices (continued) To use network functions of the projector, connect the LAN port to the computer's LAN port. To use NETWORK BRIDGE function, also connect the CONTROL port and an RS-232C port of the external device to communicate as a network terminal. See the “Network Guide”...

  • Page 99: Connecting Power Supply

    Connecting power supply Put the connector of the power cord into the AC IN (AC inlet) of the projector. Firmly plug the power cord’s plug into the outlet. In a couple of seconds after the power supply connection, the POWER indicator will light up in steady orange.

  • Page 100: Adjusting The Projector's Elevator

    Adjusting the projector's elevator When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the 3° projector horizontally. Using the feet can also tilt the projector in order to project at a suitable angle to the screen, elevating the front side of the projector within 3 degrees.

  • Page 101: Displaying The Picture

    Displaying the picture Activate your signal source. Turn the signal source on, and make it send the signal to MY SOURCE/ COMPUTER VIDEO DOC.CAMERA the projector. ASPECT AUTO SEARCH BLANK VOLUME+ button MAGNIFY FREEZE PAGE VOLUME Use the VOLUME + / VOLUME - buttons VOLUME- button DOWN to adjust the volume.

  • Page 102: Turning Off The Power

    Turning off the power STANDBY/ON button Press the STANDBY/ON button on the POWER indicator projector or the remote control. STANDBY/ON INPUT MENU LAMP The message “Power off?” will appear on TEMP the screen for about 5 seconds. POWER Press the STANDBY/ON button again while the message appears.

  • Page 103: Replacing The Lamp

    Replacing the lamp A lamp has finite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended.
  • Page 104 Replacing the lamp (continued) HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE WARNING ►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.

  • Page 105: Cleaning And Replacing The Air Filter

    Cleaning and replacing the air filter The air filter has two kinds of filters inside. Please check and clean the air filter periodically. When the indicators or a message prompts you to clean the air filter, comply with it as soon as possible.

  • Page 106: Replacing The Internal Clock Battery

    Replacing the internal clock battery Consumption of the battery makes the clock not to work correctly. When the clock is wrong or it has stopped, please replace the battery according to the following procedures. Battery Cover Turn the projector off, and unplug the power cord. Allow the projector to cool sufficiently.

  • Page 107: Using The Cd Manual

    Using the CD manual The other manuals for this product are written into the included CD-ROM titled “User’s Manual (detailed)”. Before using the CD-ROM, please read the following to ensure the proper use. System requirements The system for using the CD-ROM requires the following. Windows OS:Microsoft Windows...

  • Page 108: Specifications

    Specifications Item Specification Product name Liquid crystal projector Liquid Crystal Panel 786,432 pixels (1024 horizontal x 768 vertical) Lamp 180W UHB Speaker Power supply AC 100-120V / 3.1A, AC220-240V / 1.5A Power consumption 270W Temperature range 5 ~ 35°C (Operating) 333 (W) x 103 (H) x 303 (D) mm Size * Not including protruding parts.

  • Page 109: Troubleshooting - Warranty And After-Service

    They will tell you what warranty condition is applied. Please check the following web address where you may find the latest information for this projector. http://www.hitachi.us/digitalmedia http://www.hitachidigitalmedia.com NOTE • The information in this manual is subject to change without notice.
  • Page 111 Projector ED-D10N/ED-D11N User's Manual (detailed) Network Guide Thank you for purchasing this projector. Web control MY IMAGE (Still Image Transfer) Display Messenger Function WARNING NOTE Trademark acknowledgment ® ® ® ® ®...
  • Page 112 Content Content ..................2 1. Main functions ................3 2. Equipment connection and network setting ......5 3. Network Functions ..............11...
  • Page 113 1. Main functions 1.2 MY IMAGE (Still image Transfer) Display...
  • Page 114 1. Main functions 1.3 Messenger Function...
  • Page 115 2. Equipment connection and network setting 2.1 Required equipment preparation NOTE SETUP menu in the User’s Manual – Operating Guide...
  • Page 116 2. Equipment connection and network setting 2.2 Manual network connection setting 2.2.1 Equipments connection 2.2.2 Network settings ® ® ®...
  • Page 117 2. Equipment connection and network setting 2.2 Manual network connection setting (continued)
  • Page 118 2. Equipment connection and network setting 2.2 Manual network connection setting (continued) [About IP address] For example NOTE...
  • Page 119 2. Equipment connection and network setting 2.2 Manual network connection setting (continued) 2.2.3 “Internet Option” setting Click Click...
  • Page 120 2. Equipment connection and network setting 2.2 Manual network connection setting (continued) 2.2.4 Check connection...
  • Page 121 3. Network Functions 3.2 E-mail Alerts 3.3 Projector Management using SNMP 3.5 MY IMAGE (Still Image Transfer) Display 3.6 Messenger Function...
  • Page 122 3. Network Functions ® NOTE ® ® ®...
  • Page 123 3. Network Functions Item Description Administrator User Network Information Network Settings Port Settings Mail Settings Alert Settings Schedule Settings Date/Time Settings Security Settings Projector Control Projector Status Network Restart...
  • Page 124 3. Network Functions 3.1.1 Logon Example 192.168.1.10: “http://192.168.1.10/” [Logon] Item Password...
  • Page 125 3. Network Functions 3.1.2 Network Information 13, 14 Item Description Projector Name DHCP IP Address Subnet Mask Default Gateway MAC Address Firmware Date Firmware Version...
  • Page 126 3. Network Functions 3.1.3 Network Settings Item Description DHCP ON DHCP OFF IP Address Subnet Mask Default Gateway Projector Name sysLocation (SNMP) sysContact (SNMP) DNS Server Address AMX D.D. (AMX Device Discovery) [Apply] NOTE [Network Restart]...
  • Page 127 3. Network Functions 3.1.4 Port Settings Item Description Network Control Port1 (Port:23) Port open [Enable] [Enable] Authentication Network Control Port2 (Port:9715) Port open [Enable] [Enable] Authentication PJLink Port (Port:4352) Port open [Enable] [Enable] Authentication Image Transfer Port (Port:9716) Port open [Enable] [Enable] Authentication...
  • Page 128 3. Network Functions Item Description SNMP Port Port open [Enable] Trap address Network Settings SMTP Port Port open [Enable] Network Bridge Port Port Number [Apply] NOTE [Network Restart]...
  • Page 129 3. Network Functions 3.1.5 Mail Settings Item Description [Enable] Send mail SMTP Server Address Network Settings Sender E-mail address [TO] [CC] Recipient E-mail address [Apply] NOTE [Send Test Mail] [Send Test Mail]...
  • Page 130 3. Network Functions 3.1.6 Alert Settings Alert Item Description Cover Error Fan Error Lamp Error Temp Error Air Flow Error Cold Error Filter Error Other Error Schedule Execution Error Lamp Time Alarm Filter Time Alarm Transition Detector OPTION menu in the User’s Alarm Manual –...
  • Page 131 3. Network Functions Setting Item Description Alarm Time Lamp Time Alarm Filter Time Alarm SNMP Trap [Enable] [Enable] Send Mail Cold Start Authentication Failure Mail Subject Cold Start Authentication Failure Mail Text Cold Start Authentication Failure [Apply] NOTE Filter Error OPTION menu in the User’s Manual –...
  • Page 132 3. Network Functions 3.1.7 Schedule Settings Item Description Daily Sunday Monday Tuesday Wednesday Thursday Friday Saturday...
  • Page 133 3. Network Functions Item Description Schedule [Enable] Date (Month/Day) [Apply] Item Description Time Command [Parameter] Power Input Source Display Image Display Text [Register] [Delete] [Reset] NOTE...
  • Page 134 3. Network Functions 3.1.8 Date/Time Settings Item Description Current Date year/month/day Current Time hour:minute:second [ON] Daylight Savings Time Start Month Week hour Time minute Month Week hour Time minute...
  • Page 135 3. Network Functions Item Description Time difference [ON] SNTP SNTP Server Address Network Settings Cycle hour:minute [Apply] NOTE [Network Restart]...
  • Page 136 3. Network Functions 3.1.9 Security Settings Item Description Administrator authority Administrator ID Administrator Password Re-enter Administrator Password User authority User ID User Password Re-enter User Password...
  • Page 137 3. Network Functions Item Description Network Control Authentication Password Re-enter Authentication Password SNMP Community name [Apply NOTE [Network Restart]...
  • Page 138 3. Network Functions 3.1.10 Projector Control NOTE [Refresh] Item Description Main Power Input Source Picture Mode Blank On/Off Mute Freeze Magnify Magnify Position V Magnify Position H Template My Image My Image Delete Picture Brightness Contrast Gamma Color Temp Color Tint Sharpness My Memory Save...
  • Page 139 3. Network Functions Item Description Image Aspect Over Scan V Position H Position H Phase H Size Auto Adjust Execute Input Progressive Video NR Color Space S-Video Format C-Video Format HDMI Format HDMI Range Computer in1 COMPUTER IN1 Computer in2 COMPUTER IN2 Frame Lock - Computer in1...
  • Page 140 3. Network Functions Item Description Audio Volume Speaker Audio Source - COMPUTER IN1 Computer in1 Audio Source - COMPUTER IN2 Computer in2 Audio Source - HDMI HDMI Audio Source - S-VIDEO S-Video Audio Source - VIDEO Video Audio Out Standby HDMI Audio Screen Language...
  • Page 141 3. Network Functions Item Description Option Auto Search Direct Power On Auto Power Off MY BUTTON1 My Button-1 MY BUTTON2 My Button-2 My Source Remote Freq. Normal Remote Freq. High...
  • Page 142 3. Network Functions 3.1.11 Projector Status Item Description Error Status Lamp Time Filter Time Power Status Input Status Blank On/Off Mute Freeze...
  • Page 143 3. Network Functions 3.1.12 Network Restart Item Description Restart NOTE [Restart] 3.1.13 Logoff [Logoff]...
  • Page 144 3. Network Functions 3.2 E-mail Alerts NOTE Mail Settings ( Example 192.168.1.10: “http://192.168.1.10/” [Logon] [Port Settings] [Enable] SMTP Port [Apply] NOTE SMTP Port [Network Restart] [Mail Settings] 3.1.5 Mail Settings [Apply] NOTE [Send Test Mail] [Mail Settings]...
  • Page 145 3. Network Functions 3.2 E-mail Alerts (continued) [Alert Settings] 3.1.6 Alert Settings [Apply]...

  • Page 146: Projector Management Using Snmp

    3. Network Functions 3.3 Projector Management using SNMP NOTE SNMP Settings ( Example 192.168.1.10: “http://192.168.1.10/” [Logon] [Port Settings] [Enable] SNMP Port NOTE SNMP Port [Network Restart] [Security Settings] [SNMP] NOTE Community name [Network Restart] [Alert Settings] [Enable] [Enable] [Apply]...
  • Page 147 3. Network Functions NOTE...
  • Page 148 3. Network Functions Schedule Settings ( Example 192.168.1.10: “http://192.168.1.10/” [Logon] [Schedule Settings] [Sunday] [Enable] [Apply] [Register] [Delete] NOTE...
  • Page 149 3. Network Functions Date/Time Settings ( Example 192.168.1.10: “http://192.168.1.10/” [Logon] [Date/Time Settings] 3.1.8 Data/Time Settings [Apply] NOTE Daylight Savings Time SNTP Manual (concise)
  • Page 150 3. Network Functions 3.5 MY IMAGE (Still Image Transfer) Display NETWORK menu in the User’s Manual – Operating Guide NOTE MY BUTTON OPTION menu in the User’s Manual – Operating Guide...
  • Page 151 3. Network Functions Example 192.168.1.10: "http://192.168.1.10/" [Logon] [Port Settings] [Enable] Image Transfer Port (Port: 9716) [Enable] [Authentication] [Apply] [Security Settings] [Network Control] [Apply] NOTE Network Control Port1 (Port: 23) Network Control Port2 (Port: 9715) PJLink™ Port (Port: 4352) Image Transfer Port (Port: 9716) Text Transfer Port (Port: 9719) [Network Restart]...

  • Page 152: Messenger Function

    3. Network Functions 3.6 Messenger Function NOTE MY BUTTON OPTION menu in the User’s Manual – Operating Guide...
  • Page 153 3. Network Functions 3.6 Messenger Function (continued) Example 192.168.1.10: "http://192.168.1.10/" [Logon] [Port Settings] [Enable] Text Transfer Port (Port: 9719) [Enable] [Authentication] [Apply] [Security Settings] [Network Control] [Apply] NOTE Network Control Port1 (Port: 23) Network Control Port2 (Port: 9715) PJLink™ Port (Port: 4352) Image Transfer Port (Port: 9716) Text Transfer Port (Port: 9719) [Network Restart]...
  • Page 154 3. Network Functions Communication Port (Network Control Port1 (Port: 23)) (Network Control Port2 (Port: 9715)) NOTE Command Control Settings ( Example 192.168.1.10: “http://192.168.1.10/” [Logon] [Port Settings] [Enable] Network Control Port1 (Port: 23) [Enable] [Authentication] [Enable] Network Control Port2 (Port: 9715) [Enable] [Authentication] [Apply]...
  • Page 155 3. Network Functions [Security Settings] [Network Control] [Apply] NOTE Network Control Port1 (Port: 23) Network Control Port2 (Port: 9715) PJLink™ Port (Port: 4352) Image Transfer Port (Port: 9716) Text Transfer Port (Port: 9719) [Network Restart]...
  • Page 156 3. Network Functions Command Format “RS-232C Communication” in the User’s Manual – Operating Guide (Technical) Reply Error code Send Data format “RS-232C Communication” in the User’s Manual – Operating Guide (Technical) Connection Header Data length RS-232C command Check Sum...
  • Page 157 3. Network Functions Reply Data format Connection Reply Connection Reply Connection Reply Error code Connection Reply Data Connection Reply Status code Authentication Connection Reply Error code...
  • Page 158 3. Network Functions Authentication NOTE...
  • Page 159 3. Network Functions CONTROL CONTROL NOTE Operating Guide (Technical)
  • Page 160 3. Network Functions 3.8.2 Communication setup Operating Guide CONTROL CONTROL Item Condition CONTROL NOTE CONTROL 3.8.3 Communication port Network Bridge Port NOTE Network Bridge Port...
  • Page 161 3. Network Functions 3.8.4 Transmission method Operating Guide 3.8.4.1 HALF-DUPLEX OPTION menu - SERVICE -...
  • Page 162 3. Network Functions OPTION menu - SERVICE - NOTE 3.8.4.2 FULL-DUPLEX NOTE...
  • Page 163 Projector ED-D10N/ED-D11N User's Manual (detailed) Operating Guide – Technical Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode 720 x 400 37.9 85.0 VESA TEXT 640 x 480 31.5 59.9 VESA VGA (60Hz) 640 x 480 37.9 72.8 VESA...
  • Page 164 Initial set signals Initial set signals Back porch (B) Front porch (D) Back porch (b) Front porch (d) Active video (C) Active video (c) Data Data H. Sync. V. Sync. Sync (A) Sync (a) Vertical signal timing (lines) 720 x 400 / TEXT 20.3 640 x 480 / VGA (60Hz) 25.4...
  • Page 165 Connection to the ports NOTICE HDMI COMPUTER IN1, COMPUTER IN2, MONITOR OUT (1) for PC signal Signal Signal Video Red Ground Video Green Ground Ground Red V. sync. Ground Green (2) for Component signal Signal Signal Ground Ground Ground Ground Ground...
  • Page 166 Connection to the ports (continued) To input component video signal to COMPUTER IN ports HDMI COMPONENT VIDEO OUT COMPUTER IN1 or IN2 COMPUTER IN1 and IN2...
  • Page 167 Connection to the ports (continued) HDMI S-VIDEO Signal Ground Ground VIDEO...
  • Page 168 Connection to the ports (continued) HDMI AUDIO IN1, AUDIO IN2 AUDIO IN3 AUDIO OUT...
  • Page 169 Connection to the ports (continued) HDMI CONTROL 9 8 7 5 4 3 2 1 Signal Signal Signal Ground HDMI 18 16 14 12 10 19 17 15 13 11 Signal Signal Signal Signal Signal Signal 1 TX+ 2 TX- 3 RX+ 6 RX-...
  • Page 170 PJLink command 0 = Standby 0 = Standby 20 = MUTE off AVMT AV Mute 21 = MUTE on 30 = AV MUTE off 31 = AV MUTE on 20 = MUTE off AV Mute inquiry 21 = MUTE on 30 = AV MUTE off 31 = AV MUTE on Error Status inquiry...
  • Page 171 PJLink command (continued) 11 12 22 23 31 NOTE...
  • Page 172 RS-232C Communication 19). command table ( Connection CONTROL RS-232C CONTROL RS-232C Cable (cross) CONTROL 9 8 7 5 4 3 2 1 RTS (7) (7) RTS RI (9)
  • Page 173 RS-232C Communication (continued) Communicaion settings 1. Protocol 2. Command format Header Setting Header Action code size code Action <SET> (aH) (bH) (cH) <GET> (aH) (bH) (aH) (bH) (aH) (bH) (aH) (bH) [Header code] [Packet] [Data size] ~ 4. For byte number refer to 19).
  • Page 174 RS-232C Communication (continued) 3. Response code / Error code (1) ACK reply : 06h (2) NAK reply : 15h (3) Error reply : 1Ch + 0000h (4) Data reply : 1Dh + xxxxh NOTE...
  • Page 175 Command Control via the Network 19). command table ( Connection LAN cable (CAT-5 or greater)
  • Page 176 Command Control via the Network Communicaion Port Port Settings [Enable] [Network Control Port1 (Port: 23)] Network Control [Enable] Port1 (Port: 23) [Authentication] is required. [Enable] [Network Control Port2 (Port: 9715)] Network Control Port2 (Port: 9715) [Enable] [Authentication] is required. Security Settings [Network Network Control Control Port1 (Port: 23)] and [Network...

  • Page 177: Command Control Settings

    Command Control via the Network (continued) Command control settings [TCP #23] 1. Command format 2. Response code / Error code (1) ACK reply : 06h 11). (2) NAK reoly : 15h 11). (3) Error reply : 1Ch + 0000h 11). (4) Data reply : 1Dh + xxxxh 11).
  • Page 178 Command Control via the Network (continued) 2. Response code / Error code (1) ACK reply : 06h + ××h (2) NAK reoly : 15h + ××h (3) Error reply : 1Ch + 0000h + ××h (4) Data reply : 1Dh + xxxxh + ××h (5) Authentication error reply : 1Fh + 0400h + ××h (6) Projector busy reply: 1Fh + ××××h + ××h Automatic Connection Break...
  • Page 179 Network Bridge Communication 3.7 Controlling the external device via the projector(using the NETWORK BRIDGE function) - Network Guide. Connection cable. CONTROL OPTION menu - SERVICE - COMMUNICATION in the User's Manual - Operating Guide) CONTROL RS-232C...

  • Page 180: Communication Settings

    Network Bridge Communication Communication settings OPTION menu - SERVICE - COMMUNICATION in the User's Manual - Operating Guide) Item Start bit NOTE 3.8.4 Transmission method- Network Guide.
  • Page 181 RS-232C Communication / Network command table Command Data Names Operation Type Header Action Type Setting Code Power BE EF 06 00 2A D3 01 00 00 60 00 00 BE EF 06 00 BA D2 01 00 00 60 01 00 BE EF 06 00 19 D3...
  • Page 182 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code GAMMA #1 DEFAULT BE EF 06 00 07 E9 01 00 A1 30 20 00 #2 DEFAULT BE EF 06 00 97 E8 01 00 A1 30 21 00...
  • Page 183 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code User Gamma Point 8 BE EF 06 00 7C FF 02 00 97 30 00 00 Increment BE EF 06 00 1A FF 04 00 97 30 00 00...
  • Page 184 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code COLOR BE EF 06 00 B5 72 02 00 02 22 00 00 Increment BE EF 06 00 D3 72 04 00 02 22 00 00 Decrement BE EF...
  • Page 185 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code H SIZE BE EF 06 00 B5 82 02 00 02 21 00 00 Increment BE EF 06 00 D3 82 04 00 02 21 00 00 Decrement...
  • Page 186 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code FRAME LOCK – BE EF 06 00 3B C2 01 00 50 30 00 00 COMPUTER IN1 BE EF 06 00 AB C3 01 00 50 30 01 00...
  • Page 187 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code VOLUME - BE EF 06 00 FD CD 02 00 64 20 00 00 COMPUTER IN2 Increment BE EF 06 00 9B CD 04 00 64 20 00 00...
  • Page 188 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code AUDIO OUT STANDBY Set BE EF 06 00 EA DE 01 00 3F 20 00 00 AUDIO1 BE EF 06 00 7A DF 01 00 3F 20 01 00...
  • Page 189 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code MENU POSITION V BE EF 06 00 40 D7 02 00 16 30 00 00 Increment BE EF 06 00 26 D7 04 00 16 30 00 00 Decrement...
  • Page 190 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code AUTO POWER OFF BE EF 06 00 08 86 02 00 10 31 00 00 Increment BE EF 06 00 6E 86 04 00 10 31 00 00 Decrement...
  • Page 191 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code REMOTE FREQ. Disable BE EF 06 00 FF 3D 01 00 30 26 00 00 NORMAL Enable BE EF 06 00 6F 3C 01 00 30 26 01 00...
  • Page 192 Hitachi Consumer Electronics Co. Ltd., Shin-Otemachi Bldg 5f, 2-1, Otemachi 2-Chome, Chiyoda-Ku, Tokyo 100-0004 Japan HITACHI EUROPE LTD. HITACHI EUROPE S.A. Consumer Affairs Department 364, Kifissias Ave. & 1, Delfon Str. PO Box 3007 152 33 Chalandri Maidenhead Athens Berkshire SL6 8ZE...

This manual is also suitable for:

Ed-d10n

Table of Contents