This Simple Network Management Protocol Reference Guide describes how to use SNMP to manage and monitor the HP StorageWorks SN6000 and 8/20q Switch products. It is intended for users responsible for supporting SNMP and SN6000 and 8/20q Fibre Channel Switch configurations.
Page 2
Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. QuickTools™ is a trademark of QLogic Corporation. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Page 11
(1.3.6.1.2.1.75.1.5.1.1.4)........166 HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Page 12
11 connUnitRevsDescription return values ..........82 12 ConnUnitSensorName return for for 8/20q FC Switch and SN6000 Single Power Supply FC Switch . . 84...
Page 13
40 Document conventions ............179 HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
This Simple Network Management Protocol reference guide describes how to use SNMP to manage and monitor the HP StorageWorks SN6000 and 8/20q Switch products. Specifically, this guide describes the SNMP agent that resides on the switch.
Structure of Management Information (SMI) in the Request For Comment (RFC) 1 155. The latest Internet MIB is in RFC 1213 and is sometimes called MIB-II. User Datagram Protocol The SN6000 and 8/20q Fibre Channel Switches support the following UDP settings: • Agents listen on UDP port 161.
One or more in-band switches can be managed by an out-of-band SN6000 and 8/20q Fibre Channel Switch acting as a proxy switch. • An SN6000 or 8/20q Fibre Channel Switch can only act as a proxy for other SN6000 or 8/20q Fibre Channel Switches. •...
Page 18
Current Values: SnmpEnabled True Contact <sysContact undefined> Location <sysLocation undefined> ReadCommunity public WriteCommunity private AuthFailureTrap False ProxyEnabled True SNMPv3Enabled False New Value (press ENTER to not specify value, 'q' to quit): SnmpEnabled (True / False) Contact (string, max=64 chars) Location (string, max=64 chars) ReadCommunity (string, max=32 chars)
Page 19
(string, max=32 chars) SNMP Trap 4 Configuration - may optionally use 'set setup snmp trap 4' command. Current Values: Trap4Enabled False Trap4Address 0.0.0.0 Trap4Port Trap4Severity warning Trap4Version HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Page 20
Trap4Community public New Value (press ENTER to not specify value, 'q' to quit) : Trap4Enabled (True / False) Trap4Address (hostname, IPv4, or IPv6 Address) Trap4Port (decimal value, 1-65535) Trap4Severity (select a severity level) 1=unknown 6=warning 2=emergency 7=notify 3=alert 8=info 4=critical 9=debug 5=error 10=mark...
To configure an SN6000 or 8/20q Fibre Channel Switch using Enterprise Fabric Management Suite, see the SNMP Configuration section and the SNMP v3 Security section in the HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Enterprise Fabric Management Suite User Guide.
MIB-II Objects This section contains detailed information about the MIB-II objects on the SN6000 or 8/20q Fibre Channel Switch. A MIB defines the properties of the managed object within the device to be managed. Every managed device keeps a database of values for each definition written in the MIB. It is not the actual database itself;...
Read-only Status Mandatory Return value The value for the 8/20q FC switch is 1.3.6.1.4.1.3873.1.11. The value for the SN6000 Dual Power Supply FC switch is 1.3.6.1.4.1.3873.1.25. The value for the SN6000 Single Power Supply FC switch is 1.3.6.1.4.1.3873.1.24. sysUpTime (1.3.6.1.2.1.1.3) The time, in hundredths of a second, since the network management portion of the system was last re-initialized.
Status Mandatory Return value The default for the SN6000 Fibre Channel Switch is SN6000 FC Switch. The default for the 8/20q Fibre Channel Switch is 8/20q FC Switch. sysLocation (1.3.6.1.2.1.1.6) The physical location of this node, such as telephone closet and 3rd floor.
Mandatory Return value The default is 2. The Interfaces table The Interfaces table contains information on the entity's interfaces. Each interface is thought of as being attached to a subnetwork. This term should not be confused with subnet, which refers to an addressing partitioning scheme used in the Internet suite of protocols.
Writes not supported. ifOperStatus (1.3.6.1.2.1.2.2.1.8) The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed. Syntax INTEGER Access HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Read-only Status Mandatory ifLastChange (1.3.6.1.2.1.2.2.1.9) The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, this object contains a value zero (0). Syntax TimeTicks Access...
The total number of packets that higher level protocols requested be transmitted to a subnetwork unicast address, including those packets that were discarded or not sent. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Syntax Counter Access Read-only Status Mandatory ifOutNUcastPkts (1.3.6.1.2.1.2.2.1.18) The total number of packets that higher level protocols requested be transmitted to a non-unicast (subnetwork broadcast or subnetwork multicast) address, including those packets that were discarded or not sent. Syntax Counter Access Read-only Status...
Proper interpretation of such entries requires examination of the relevant atPhysAddress object. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Syntax PhysAddress Access Read-write Status Deprecated atNetAddress (1.3.6.1.2.1.3.1.1.3) The NetworkAddress corresponding to the media-dependent “physical” address. Syntax NetworkAddress Access Read-write Status Deprecated The IP group Implementation of the IP group is mandatory for all systems. ipForwarding (1.3.6.1.2.1.4.1) The indication of whether this entity is acting as an IP gateway with respect to the forwarding of datagrams received by, but not addressed to, this entity.
Source Routed from this entity, and the Source Route option processing was successful. Syntax Counter Access Read-only HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Status Mandatory ipInUnknownProtos (1.3.6.1.2.1.4.7) The number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol. Syntax Counter Access Read-only Status Mandatory ipInDiscards (1.3.6.1.2.1.4.8) The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but were discarded (for example, for lack of buffer space).
Access Read-only Status Mandatory ipReasmReqds (1.3.6.1.2.1.4.14) The number of IP fragments received that needed to be reassembled at this entity. Syntax Counter Access Read-only Status Mandatory HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
ipReasmOKs (1.3.6.1.2.1.4.15) The number of IP datagrams successfully reassembled. Syntax Counter Access Read-only Status Mandatory ipReasmFails (1.3.6.1.2.1.4.16) The number of failures detected by the IP reassembly algorithm (for example, timed out, and errors). This is not necessarily a count of discarded IP fragments, since some algorithms (notably the algorithm in RFC 815) can lose track of the number of fragments when they are combining them as they are received.
1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Syntax INTEGER Access Read-only Status Mandatory ipAdEntReasmMaxSize (1.3.6.1.2.1.4.20.1.5) The size of the largest IP datagram that this entity can reassemble from incoming IP fragmented datagrams received on this interface. Syntax INTEGER (0..65535) Access Read-only Status Mandatory The IP Routing table The IP routing table contains an entry for each route presently known to this entity.
An alternate routing metric for this route. The semantics of this metric are determined by the routing protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to - 1 . Syntax INTEGER HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Access Read-write Status Mandatory Return value Writes not supported. ipRouteNextHop (1.3.6.1.2.1.4.21.1.7) The IP address of the next hop of this route. In the case of a route bound to an interface that is realized from a broadcast media. The value of this field is the agent's IP address on that interface. Syntax IpAddress Access...
OBJECT IDENTIFIER { 0 0 }, which is a syntactically valid object identifier. Any conformant implementation of ASN.1 and BER must be able to generate and recognize this value. Syntax OBJECT IDENTIFIER HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Access Read-only Status Mandatory The IP Address Translation table The IP address translation table contain the IpAddress to “physical” address equivalences. Some interfaces do not use translation tables for determining address equivalences (for example, DDN-X.25 has an algorithmic method). If all interfaces are of this type, then the Address Translation table is empty, that is, it has zero entries.
Mandatory icmpInErrors (1.3.6.1.2.1.5.2) The number of ICMP messages received by the entity but were determined to have ICMP-specific errors (such as, bad ICMP checksums, bad length). HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Syntax Counter Access Read-only Status Mandatory icmpInDestUnreachs (1.3.6.1.2.1.5.3) The number of ICMP Destination Unreachable messages received. Syntax Counter Access Read-only Status Mandatory icmpInTimeExcds (1.3.6.1.2.1.5.4) The number of ICMP Time Exceeded messages received. Syntax Counter Access Read-only Status Mandatory icmpInParmProbs (1.3.6.1.2.1.5.5) The number of ICMP Parameter Problem messages received.
The number of ICMP Timestamp (request) messages received. Syntax Counter Access Read-only Status Mandatory icmpInTimestampReps (1.3.6.1.2.1.5.1 1) The number of ICMP Timestamp Reply messages received. Syntax Counter Access Read-only HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Status Mandatory icmpInAddrMasks (1.3.6.1.2.1.5.12) The number of ICMP Address Mask Request messages received. Syntax Counter Access Read-only Status Mandatory icmpInAddrMaskReps (1.3.6.1.2.1.5.13) The number of ICMP Address Mask Reply messages received. Syntax Counter Access Read-only Status Mandatory icmpOutMsgs (1.3.6.1.2.1.5.14) The total number of ICMP messages that this entity attempted to send. This counter includes all those messages counted by icmpOutErrors.
The number of ICMP Redirect messages sent. For a host, this object is always zero, since hosts do not send redirects. Syntax Counter Access Read-only Status Mandatory HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
icmpOutEchos (1.3.6.1.2.1.5.21) The number of ICMP Echo (request) messages sent. Syntax Counter Access Read-only Status Mandatory icmpOutEchoReps (1.3.6.1.2.1.5.22) The number of ICMP Echo Reply messages sent. Syntax Counter Access Read-only Status Mandatory icmpOutTimestamps (1.3.6.1.2.1.5.23) The number of ICMP Timestamp (request) messages sent. Syntax Counter Access...
For example, when the timeout algorithm is rsre(3), an object of this type has the semantics of the UBOUND quantity described in RFC 793. Syntax INTEGER HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Access Read-only Status Mandatory tcpMaxConn (1.3.6.1.2.1.6.4) The limit on the total number of TCP connections the entity can support. In entities where the maximum number of connections is dynamic, this object should contain the value -1. Syntax INTEGER Access Read-only Status Mandatory tcpActiveOpens (1.3.6.1.2.1.6.5)
Read-only Status Mandatory tcpRetransSegs (1.3.6.1.2.1.6.12) The total number of segments retransmitted. That is, the number of TCP segments transmitted containing one or more previously transmitted octets. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Syntax Counter Access Read-only Status Mandatory The TCP Connection table The TCP connection table contains information about this entity's existing TCP connections. tcpConnState (1.3.6.1.2.1.6.13.1.1) The state of this TCP connection. The only value that may be set by a management station is deleteTCB(12).
Implementation of the UDP group is mandatory for all systems that implement the UDP. udpInDatagrams (1.3.6.1.2.1.7.1) The total number of UDP datagrams delivered to UDP users. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Syntax Counter Access Read-only Status Mandatory udpNoPorts (1.3.6.1.2.1.7.2) The total number of UDP datagrams received for which there was no application at the destination port. Syntax Counter Access Read-only Status Mandatory udpInErrors (1.3.6.1.2.1.7.3) The number of received UDP datagrams that could not be delivered for reasons other than the lack of an application at the destination port.
The number of EGP messages received that proved to be in error. Syntax Counter Access Read-only Status Mandatory egpOutMsgs (1.3.6.1.2.1.8.3) The total number of locally generated EGP messages. Syntax Counter Access Read-only Status Mandatory HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
egpOutErrors (1.3.6.1.2.1.8.4) The number of locally generated EGP messages not sent due to resource limitations within an EGP entity. Syntax Counter Access Read-only Status Mandatory The EGP Neighbor table The EGP neighbor table contains information about this entity's EGP neighbors. egpNeighState (1.3.6.1.2.1.8.5.1.1) The EGP state of the local system with respect to this entry's EGP neighbor.
EGP entity. Syntax Counter Access Read-only Status Mandatory egpNeighInErrMsgs (1.3.6.1.2.1.8.5.1.8) The number of EGP-defined error messages received from this EGP peer. Syntax Counter Access Read-only HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Status Mandatory egpNeighOutErrMsgs (1.3.6.1.2.1.8.5.1.9) The number of EGP-defined error messages sent to this EGP peer. Syntax Counter Access Read-only Status Mandatory egpNeighStateUps (1.3.6.1.2.1.8.5.1.10) The number of EGP state transitions to the UP state with this EGP peer. Syntax Counter Access Read-only Status Mandatory...
Typically, such definitions reside in the experimental portion of the MIB until they are proven. Then, HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
as part of the Internet standardization process, the definitions are elevated to accepted status, and a new object identifier under the transmission group is defined. By convention, the name assigned is: type OBJECT IDENTIFIER ::= { transmission number }. Where type is the symbolic value used for the media in the ifType column of the ifTable object, and number is the actual integer value corresponding to the symbol.
The total number of SNMP PDUs delivered to the SNMP protocol entity and for which the value of the error-status field is NoSuchName. Syntax Counter Access Read-only Status Mandatory HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
snmpInBadValues (1.3.6.1.2.1.1 1.10) The total number of SNMP PDUs delivered to the SNMP protocol entity and for which the value of the error-status field is badValue. Syntax Counter Access Read-only Status Mandatory snmpInReadOnlys (1.3.6.1.2.1.1 1.1 1) The total number valid SNMP PDUs delivered to the SNMP protocol entity and for which the value of the error-status field is readOnly.
Status Mandatory snmpInGetResponses (1.3.6.1.2.1.1 1.18) The total number of SNMP GetResponse PDUs accepted and processed by the SNMP protocol entity. Syntax Counter Access Read-only Status Mandatory HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
snmpInTraps (1.3.6.1.2.1.1 1.19) The total number of SNMP Trap PDUs accepted and processed by the SNMP protocol entity. Syntax Counter Access Read-only Status Mandatory snmpOutTooBigs (1.3.6.1.2.1.1 1.20) The total number of SNMP PDUs generated by the SNMP protocol entity and for which the value of the error-status field is tooBig.
The total number of SNMP GetResponse PDUs generated by the SNMP protocol entity. Syntax Counter Access Read-only Status Mandatory snmpOutTraps (1.3.6.1.2.1.1 1.29) The total number of SNMP Trap PDUs generated by the SNMP protocol entity. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Syntax Counter Access Read-only Status Mandatory snmpEnableAuthenTraps (1.3.6.1.2.1.1 1.30) Indicates whether the SNMP agent process is permitted to generate authentication-failure traps. The value of this object overrides any configuration information; as such, it provides a means whereby all authentication-failure traps may be disabled. It is strongly recommended that this object be stored in non-volatile memory so that it remains constant between re-initializations of the network management system.
Table 3 FA-MIB textual substitutions (continued) Description Syntax FcUnitType INTEGER { unknown(1) other(2)–None of the following hub(3)– Passive connectivity unit supporting loop protocol switch(4)–Active connectivity unit supporting multiple protocols gateway(5)–Unit that converts not only the interface but also encapsulates the frame into another protocol. The assumption is that there is always two gateways connected together.
(1.3.6.1.3.94.1.3) The sysUpTime timestamp at which the last status change occurred for any members of the set, in centiseconds. Syntax TimeTicks Access read only Status obsolete HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Return value The sysUpTime timestamp at which the last status change occurred. configurationChangeTime (1.3.6.1.3.94.1.4) The sysUpTime timestamp at which the last configuration change occurred for any members of the set, in centiseconds. This represents a union of change information for connUnitConfigurationChangeTime.
Return value The number of ports on the switch. connUnitState (1.3.6.1.3.94.1.6.1.5) The operational state of the switch mapped. The overall state of the connectivity unit. Syntax INTEGER HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Access Read-only Status Mandatory Return value Table 4 for switch operational states. Table 4 Switch operational states Switch state Return state online online(2) offline offline(3) diagnostics offline(3) other unknown connUnitStatus (1.3.6.1.3.94.1.6.1.6) Overall status of the connectivity unit. The goal of this object is to be the single poll point to check to the status of the connUnit.
Mandatory Return value Returns the SystemDescription of connected switches. The value for the 8/20q FC switch is HP StorageWorks 8/20q Fibre Channel Switch. The value for the SN600 FC switch is either HP StorageWorks SN6000 Stackable Dual Power Supply Fibre Channel Switch or HP StorageWorks SN6000 Stackable Single Power Supply Fibre Channel Switch.
Mandatory Return value The switch IP address. For example: http://10.0.0.1. Writes not supported, returns NoSuchName. connUnitDomainId (1.3.6.1.3.94.1.6.1.1 1 The 24-bit Fibre Channel address ID of this connectivity unit, right-justified with leading zeros if required. This should be set to the Fibre Channel address ID, or if it is a switch, it would be set to the domain controller address.
TimeTicks Access Read-only Status obsolete Return value This object is obsolete. Always returns error status NoSuchName. connUnitNumRevs (1.3.6.1.3.94.1.6.1.17) The number of revisions in the connUnitRevsTable. Syntax HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
The number of entries in the revision table. The revision numbers of all components of the switch. HP StorageWorks 8/20q Fibre Channel Switch = 3, SN6000 Stackable Dual Power Supply FC Switch = 3, SN6000 Stackable Single Power Supply FC Switch = 3.
Each implementation may chose not to allow any or all of these values on a SET. Syntax INTEGER { unknown(1) invalid(2) resetConnUnitColdStart(3) resetConnUnitWarmStart(4) offlineConnUnit(5) onlineConnUnit(6) Access Read-write Status Mandatory Return value HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Mandatory Return value An integer indicating the number of events in the connUnitEventTable connUnitMaxEvents (1.3.6.1.3.94.1.6.1.27) Maximum number of events that can be defined in connUnitEventTable Syntax HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
INTEGER Access Read-only Status Mandatory Return value Always returns 30. connUnitEventCurrID (1.3.6.1.3.94.1.6.1.28) The last-used event ID (connUnitEventIndex). Syntax INTEGER Access Read-only Status Mandatory Return value The event ID of the last event connUnitFabricID (1.3.6.1.3.94.1.6.1.29) A globally unique value used to identify the fabric that this connUnit belongs to, otherwise empty string. This would typically be equal to the connUnitGlobalID of the primary switch in a Fibre Channel fabric.
A unique value among all connUnitRevsEntrys with the same value of connUnitRevsUnitId, in the range between 1 and connUnitNumRevs[connUnitRevsUnitId]. Syntax INTEGER (1..2147483647) Access Read-only Status Mandatory HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Return value The revision table index connUnitRevsRevId (1.3.6.1.3.94.1.7.1.3) A vendor-specific string identifying a revision of a component of the connUnit indexed by connUnitRevsUnitId. Syntax DisplayString Access Read-only Status Mandatory Return value Table 10 for connUnitRevsRevtId return values. Table 10 ConnUnitRevsRevId return values Table index Return value Active firmware image...
Mandatory Return value The sensor table index connUnitSensorName (1.3.6.1.3.94.1.8.1.3) A textual identification of the sensor intended primarily for operator use. Syntax DisplayString Access Read-only Status Mandatory HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Return value Table 12 Table 13 for connUnitSensorName return values. Table 12 ConnUnitSensorName return for for 8/20q FC Switch and SN6000 Single Power Supply FC Switch Table index Return value Power Supply 1 Status Temperature Status Temperature Sensor 1 Value...
Describes the status of the sensor as a message. It may also provide more resolution on the sensor indication. For example: Cover temperature 1503K, above nominal operating range- ::= { connUnitSensorEntry 6 }. Syntax DisplayString Access Read-only HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Status Mandatory Return value Table 17 for connUnitSensorMessage return values. Table 17 ConnUnitSensorMessage values Sensor Return value Power Supply Good/Bad/NotInstalled Good/Bad/NotInstalled Temperature Status Normal/Warm/Overheating/NotInstalled Temperature Value Degrees in C connUnitSensorType (1.3.6.1.3.94.1.8.1.7) The type of component being monitored by this sensor. Syntax INTEGER { unknown(1)
WWN of 100000c0dd0090a7, is: snmpget localhost public fcmgmt.connSet.connUnitPortTable.connUnitPortEntry.connUnitPortUni tId.16.0.0.192.221.0.144.167.0.0.0.0.0.0.0.0.1. connUnitPortUnitId (1.3.6.1.3.94.1.10.1.1) The connUnitId of the connectivity unit that contains this port. Syntax FcGlobalId Access Read-only Status Mandatory HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Return value Returns the WWN of the switch followed by 8 bytes of zeros. For example: 10 00 00 C0 DD 00 71 C9 00 00 00 00 00 00 00 00. connUnitPortIndex (1.3.6.1.3.94.1.10.1.2) A unique value among all connUnitPortEntrys on this connectivity unit, between 1 and connUnitNumPort[connUnitPortUnitId].
(0). This object has the same definition as connUnitPortFCClassCap ::= { connUnitPortEntry 5 }. Syntax OCTET STRING (SIZE (2)) Access Read-only Status Mandatory HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Return value If F or FL, returns 0x0c (Class 2, and Class 3), else returns 0x0d (Class f, Class 2, and Class 3). connUnitPortState (1.3.6.1.3.94.1.10.1.6) The user selected state of the port hardware Syntax INTEGER { unknown(1), online(2)–Available for meaningful work offline(3)–Not available for meaningful work bypassed(4)–No longer used (4/12/00) diagnostics(5)
connUnitPortModuleType (1.3.6.1.3.94.1.10.1.9) The module type of the port connector Syntax INTEGER { unknown(1) other(2) gbic(3) embedded(4)–Fixed (oneXnine) glm(5) gbicSerialId(6) gbicNoSerialId(7) gbicNotInstalled(8) smallFormFactor(9)–Generally a small form factor connector. Access Read-only Status Mandatory Return value Table 23 for connUnitPortModuleType return values. Table 23 connUnitPortModuleType return values Type Return value...
The port vendor, for example, for a GBIC. Syntax DisplayString (SIZE(0..79)) Access Read-only Status unsupported Return value The port vendor as reported by the SFP (if supported). HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
connUnitPortSpeed (1.3.6.1.3.94.1.10.1.15) The speed of the port in kilobytes per second. Syntax INTEGER Access Read-only Status Mandatory Return value The operational speed, otherwise returns the administrative speed setting. If 1 Gb/s, returns 106,250. If 2 Gb/s, returns 212,500. If 4 Gb/s, returns 425,000. If 8 Gb/s, returns 850,000. If 10 Gb/s, returns 1062500.
In that case, provide the internal representation of this port in this object. This value may also be used in the connUnitLinkPortNumberX or connUnitLinkPortNumberY objects of the connUnitLinkTable. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Syntax INTEGER Access Read-only Status Mandatory Return value The physical port number connUnitPortStatObject (1.3.6.1.3.94.1.10.1.19) This contains the Object Identifier (OID) of the first object of the table that contains the statistics for this particular port. If this has a value of zero (0), then there are no statistics available for this port. The port type information helps identify the statistics objects that are found in the table.
Return value Table 26 for connUnitPortHWState port state return values. Table 26 ConnUnitPortHWState Port state return values Port state Return value If DiagStatus = Failed Failed(2) If SFP = Not Installed NoMedia(7) If SyncStatus = SyncAcquired Active(4) If SyncStatus = SyncLost LinkDown(8) Other Unknown(1)
DisplayString (SIZE (0..15)) Access Read-only Status Mandatory Return value The timestamp of the event connUnitSEventTime (1.3.6.1.3.94.1.1 1.1.5) The sysUpTime timestamp when the event occurred. Syntax connUnitSEventTime HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide...
Access Read-only Status Mandatory Return value Always returns error status NoSuchName. connUnitEventSeverity (1.3.6.1.3.94.1.1 1.1.6) The event severity level Syntax FcEventSeverity Access Read-only Status Mandatory Return value Always returns error status NoSuchName. connUnitEventType (1.3.6.1.3.94.1.1 1.1.7) The type of this event Syntax INTEGER { unknown(1) other(2)
The WWN of the switch followed by 8 bytes of zeros. For example: 10 00 00 C0 DD 00 71 C9 00 00 00 00 00 00 00 00. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 101...
connUnitLinkIndex (1.3.6.1.3.94.1.12.1.2) This index is used to create a unique value for each entry in the link table with the same connUnitLinkUnitId. The value can only be reused if it is not currently in use and is the next candidate to be used. This value wraps at the highest value represented by the size of INTEGER. The value is reset to zero (0) when the system is reset, and the first value to be used is 1.
0" ::= { connUnitLinkEntry 8 }. Syntax FcGlobalId Access Read-only Status Mandatory Return value The remote port WWN for each entry in the link table, if known HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 103...
connUnitLinkAgentAddressY (1.3.6.1.3.94.1.12.1.9) The address of an FCMGMT MIB agent for the node identified by connUnitLinkNodeIdY, if known. Otherwise 16 octets of binary 0" ::= {connUnitLinkEntry 9}. Syntax OCTET STRING (SIZE(16)) Access Read-only Status Mandatory Return value The remote IP address of the remote switch, if known. Otherwise, returns 0000000000000000. connUnitLinkAgentAddressTypeY (1.3.6.1.3.94.1.12.1.10) If connUnitLinkAgentAddressY is non-zero, it is a protocol address.
An example of how to access one of these objects: fcmgmt.connSet.connUnitZoneTable.connUnitZoneEntry.connUnitZoneIndex.1.1 connUnitZoneIndex (1.3.6.1.3.94.1.13.1.1) The unique table index for each zone. Valid values are between 1 and connUnit-ZoneSetNumZones. Syntax INTEGER (1..2147483647) Access Read-only Status Mandatory HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 105...
Return value Returns index number for each zone within the active zoneset. connUnitZoneMemberIndex (1.3.6.1.3.94.1.13.1.2) The unique table index for each zone member. Valid values are between 1 and connUnitZoneNumMembers. Syntax INTEGER (1..2147483647) Access Read-only Status Mandatory Return value Returns index number for each member within a zone. connUnitZoneSetName (1.3.6.1.3.94.1.13.1.3) The name of the active zoneset to which the zone and zone member belong.
See FC-GS-4 draft standard for the details and format of the structure. Support of this object is optional. Syntax OCTET STRING (SIZE(80)) Access Read-only HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 107...
Status Mandatory Return value Not supported. Always returns SNMP error NoSuchName. connUnitZoneNumMembers (1.3.6.1.3.94.1.13.1.9) Number of zone members in the zone: connUnitZoneName Syntax INTEGER Access Read-only Status Mandatory Return value Returns total number of members in a zone connUnitZoneMemberIdType (1.3.6.1.3.94.1.13.1.10) The type of zone member ID: 1–Port WWN 2–Domain &...
Status Mandatory Return value Returns the alias member index connUnitZoningAliasNumAliases (1.3.6.1.3.94.1.14.1.3) The number of aliases defined in this table Syntax INTEGER Access Read-only Status Mandatory HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 109...
Return value Returns the number of aliases defined connUnitZoningAliasName (1.3.6.1.3.94.1.14.1.4) The alias name Syntax DisplayString (SIZE (0..79)) Access Read-only Status Mandatory Return value Returns the alias name connUnitZoningAliasNumMembers (1.3.6.1.3.94.1.14.1.5) The number of members in the alias connUnitZoningAliasName Syntax INTEGER Access Read-only Status Mandatory...
C9 00 00 00 00 00 00 00 00. connUnitPortStatIndex (1.3.6.1.3.94.4.5.1.2) A unique value among all entries in this table, between 0 and connUnitNum-Port[connUnitPortUnitId]. Syntax INTEGER (0..2147483647) Access Read-only HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 111...
Status Mandatory Return value The Port statistics table index connUnitPortStatCountError (1.3.6.1.3.94.4.5.1.3) A count of the errors that have occurred on this port. Syntax OCTET STRING (SIZE (8)) Access Read-only Status Mandatory Return value A hexidecimal value indicating the total number of errors for a port. connUnitPortStatCountTxObjects (1.3.6.1.3.94.4.5.1.4) The number of frames/packets/IOs/etc transmitted by this port.
(0). There is no credit to provide to other side. This is a Fibre Channel statistic only. Syntax OCTET STRING (SIZE (8)) HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 113...
Access Read-only Status Mandatory Return value Unsupported. Always returns the high-order bit to 1 and all other bits are set to zero (0). connUnitPortStatCountFBSYFrames (1.3.6.1.3.94.4.5.1.10) The count of times that FBSY was returned to this port because a frame could not be delivered to the other end of the link.
FBSY can only occur on SOFc1 frames (the frames that establish a connection). This is a Fibre Channel-only statistic. Syntax OCTET STRING (SIZE (8)) HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 115...
Access Read-only Status Mandatory Return value Unsupported. Always returns the high-order bit to 1 with all other bits set to zero (0). connUnitPortStatCountClass1PBSYFrames (1.3.6.1.3.94.4.5.1.17) The count of times that PBSY was returned to this port because of a Class 1 frame that could not be delivered to the other end of the link.
This occurs if the destination N_Port is temporarily busy. PBSY can only occur on SOFc1 frames (the frames that establish a connection). This is a Fibre Channel-only statistic. Syntax OCTET STRING (SIZE (8)) HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 117...
Access Read-only Status Mandatory Return value Unsupported. Always returns the high-order bit to 1 with all other bits set to zero (0). connUnitPortStatCountClass2FRJTFrames (1.3.6.1.3.94.4.5.1.24) The count of times that FRJT was returned to this port because of a Class 2 frame that was rejected by the fabric.
Unsupported. Always returns the high-order bit to 1 with all other bits set to zero (0). connUnitPortStatCountTxMulticastObjects (1.3.6.1.3.94.4.5.1.30) The count of Multicast frames or packets transmitted out this port. Syntax OCTET STRING (SIZE (8)) Access Read-only HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 119...
Status Mandatory Return value Unsupported. Always returns the high-order bit to 1 with all other bits set to zero (0). connUnitPortStatCountRxBroadcastObjects (1.3.6.1.3.94.4.5.1.31) The count of Broadcast frames or packets received at this port. Syntax OCTET STRING (SIZE (8)) Access Read-only Status Mandatory Return value...
The count of offline primitive OLSs transmitted by this port. This is a Fibre Channel-only statistic. Syntax OCTET STRING (SIZE (8)) Access Read-only Status Mandatory Return value The total number of TxOfflineSeqs transmitted by a port. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 121...
connUnitPortStatCountNumberOfflineSequences (1.3.6.1.3.94.4.5.1.38) The count of offline primitive sequences received at this port. This is a Fibre Channel-only statistic. Syntax OCTET STRING (SIZE (8)) Access Read-only Status Mandatory Return value The total number of TotalOfflineSeqs received by a port. connUnitPortStatCountLinkFailures (1.3.6.1.3.94.4.5.1.39) The count of link failures.
The count of invalid ordered sets received at port. This count is part of the Link Error Status Block (LESB). (FC-PH 29.8). This is a Fibre Channel-only statistic. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 123...
Syntax OCTET STRING (SIZE (8)) Access Read-only Status Mandatory Return value Unsupported. Always returns the high-order bit to 1 with all other bits set to zero (0). connUnitPortStatCountFramesTooLong (1.3.6.1.3.94.4.5.1.46) The count of frames received at this port where the frame length was greater than what was agreed to in FLOGI/PLOGI.
(1.3.6.1.3.94.5.1.1) The current number of entries in the table. Syntax INTEGER MaxAccess Read-only HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 125...
Status Mandatory Return value Returns the number of entries registered in the Simple Name Server (SNS) for all switches. connUnitSnsId (1.3.6.1.3.94.5.2.1.1.1) The connUnitId of the connectivity unit that contains this SNS table. Syntax OCTET STRING (SIZE (16)) Access Read-only Status Mandatory Return value Returns the WWN of the switch followed by 8 bytes of zeros.
The Internet Protocol version 6 (IPv6) formatted address of the node for this entry in the SNS table. Syntax OCTET STRING (SIZE (16)) Access Read-only Status Mandatory Return value The switch IP address in IPv6 format HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 127...
connUnitSnsProcAssoc (1.3.6.1.3.94.5.2.1.1.8) The process associator for this entry in the SNS table Syntax OCTET STRING (SIZE (16)) Access Read-only Status Mandatory Return value Unsupported. Always returns error status NoSuchName. connUnitSnsFC4Type (1.3.6.1.3.94.5.2.1.1.9) The FC-4 types supported by this entry in the SNS table Syntax OCTET STRING (SIZE (32)) Access...
Access Read-only Status Mandatory Return value Unsupported. Always returns error status NoSuchName. connUnitSnsSymbolicPortName (1.3.6.1.3.94.5.2.1.1.14) The symbolic port name of this entry in the SNS table HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 129...
Syntax DisplayString (SIZE (0..79)) Access Read-only Status Mandatory Return value The symbolic port name registered by the device in the SNS table. If not registered, returns (NULL). connUnitSnsSymbolicNodeName (1.3.6.1.3.94.5.2.1.1.15) The symbolic node name of this entry in the SNS table Syntax DisplayString (SIZE (0..79)) Access...
The platform name. May be either a readable string or a unique ID format as specified in the FC-GS-4 draft standard. Syntax OCTET STRING (SIZE(79)) Access Read-only HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 131...
Status Mandatory Return value Unsupported. Always returns error status NoSuchName. connUnitPlatformType (1.3.6.1.3.94.5.2.2.1.6) The platform type Syntax FcUnitType Access Read-only Status Mandatory Return value Unsupported. Always returns error status NoSuchName. connUnitPlatformLabel (1.3.6.1.3.94.5.2.2.1.7) An administratively assigned symbolic name for the platform. The Platform Label may only contain printable ASCII characters.
(1.3.6.1.3.94.5.2.2.1.12) The WWN of the node contained by the platform. Syntax FcGlobalId Access Read-only Status Read-only Return value Unsupported. Always returns error status NoSuchName. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 133...
Trap table Traps are asynchronous messages sent from the agent (residing on the switch) to the manager (residing on the workstation) to identify significant events. There can be up to five trap addresses within the trap table. All trap information is stored within the switch and is accessible to Telnet and the SNMP agent, and is persistent between boots.
A value indicating the trap severity level. See Table 28 for trap severity levels. trapRegRowState (1.3.6.1.3.94.2.3.1.4) Specifies the state of the row. • rowDestroy • READ: Can never happen. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 135...
• WRITE: Remove this row from the table. • rowInactive • READ: Indicates that this row does exist, but that traps are not enabled to be sent to the target. • WRITE: If the row does not exist, and the agent allows writes to the trap table, then a new row is created.
The software module where the event was initiated Module The address in the software module where the event was initiated Addr The description of the event Descr HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 137...
Table 30 lists the trap information returned for the connUnitEventDescr variable. Table 30 Filter trap levels Trap type Cause Filter level User port config change connUnitPortStatusChange eventSeverity_info User port state change eventSeverity_info E_Port alarm eventSeverity_critical Fabric change and unit deleted connUnitDeletedTrap eventSeverity_info Switch state change...
While all implementations of the SNMPv2 must be capable of generating this trap, the snmpEnableAuthenTraps object indicates whether or not this trap is generated. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 139...
Table 31 FE-MIB textual substitutions Description Syntax FcCosCap BITS { classF(0) class1(1) class2(2) class3(3) class4(4) class5(5) class6(6) FcFeModuleCapacity Unsigned32 FcFeFxPortCapacity Unsigned32 FcFeModuleIndex Unsigned32 FcFeFxPortIndex Unsigned32 FcFeNxPortIndex Integer32 (1..126) FcBbCreditModel INTEGER { regular(1), alternate (2) } Configuration group This group consists of scalar objects and tables. It contains the configuration and service parameters of the Fabric Element and the FxPort(s).
Current Return value A configuration description of the module table entry. The value for the 8/20q FC switch is HP StorageWorks 8/20q Fibre Channel Switch. The value for the SN600 FC switch is either HP StorageWorks SN6000 Stackable Dual Power Supply Fibre Channel Switch or HP StorageWorks SN6000 Stackable Single Power Supply Fibre Channel Switch.
Status Current Return value TThe module identification number for the 8/20q FC switch is 1.3.6.1.4.1.3873.1.11. The module identification number for the SN6000 Stackable Dual Power Supply FC switch is 1.3.6.1.4.1.3873.1.25. The module identification number for the SN6000 Stackable Single Power Supply FC switch is 1.3.6.1.4.1.3873.1.24.
This table contains one entry for each FxPort and configuration parameters of the ports. fcFxPortName (1.3.6.1.2.1.75.1.1.5.1.2) The WWN of this FxPort. Each FxPort has a unique port WWN within the fabric. Syntax FcNameId Access Read-only HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 145...
Status Current Return value Returns the port WWN for each port on switch. For example, the return value for port #2 would be 20 02 00 C0 DD 00 71 C9, and the return value for port #14 would be 20 0E 00 C0 DD 00 71 fcFxPortFcphVersionHigh (1.3.6.1.2.1.75.1.1.5.1.3) The highest or most recent version of FC-PH that the FxPort is configured to support.
Return value The default is 2000 (0x7D0). fcFxPortCosSupported (1.3.6.1.2.1.75.1.1.5.1.9) A value indicating the set of classes of service supported by the FxPort. Syntax FcCosCap Access Read-only HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 147...
Status Current Return value Always returns Class 3, 2, F (0x0D). fcFxPortIntermixSupported (1.3.6.1.2.1.75.1.1.5.1.10) A flag indicating whether or not the FxPort supports an Intermixed Dedicated Connection. Syntax TruthValue Access Read-only Status Current Return value Always returns False(2) fcFxPortStackedConnMode (1.3.6.1.2.1.75.1.1.5.1.1 1) A value indicating the mode of Stacked Connect supported by the FxPort.
The number of buffers currently available for receiving frames from the attached port in the buffer-to-buffer flow control. The value should be less than or equal to fcFxPortBbCredit. Syntax Gauge32 Access Read-only Status HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 149...
Current Return value Unsupported. Always returns error status NoSuchName. fcFxPortOperMode (1.3.6.1.2.1.75.1.2.1.1.3) The current operational mode of the FxPort Syntax INTEGER { unknown(1), fPort(2), flPort(3) } Access Read-only Status Current Return value Table 33 for fcFxPortOperMode return values. Table 33 Port operational mode return values Mode Return value Unknown...
Syntax INTEGER { online(1)–Login may proceed offline(2)–Login cannot proceed testing(3)–Port is under test linkFailure(4)–Failure after online/testing Access Read-only Status Current HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 151...
Return value Table 36 for fcFxPortPhysOperStatus return values. Table 36 fcFxPortPHysOperStatus return values Status Return value Online online(1) Offline offline(2) Diagnostics testing(3) Down linkfailure(4) fcFxPortPhysLastChange (1.3.6.1.2.1.75.1.2.2.1.3) The value of sysUpTime at the time the FxPort entered its current operational status. A value of zero (0) indicates that the FxPort operational status has not changed since the agent last restarted.
A variable indicating that the attached NxPort has requested the FxPort for the support of classes of services and the FxPort has granted the request. Syntax FcCosCap Access Read-only Status Current HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 153...
Return value The bits have the following bit-mapped definition: Bit 7 Class-six Bit 6 Class-five Bit 5 Class-four Bit 4 Class-three Bit 3 Class-two Bit 2 Class-one Bit 1 Class F For example: If Class 3, the return value is 0x10. fcFxPortIntermixSuppAgreed (1.3.6.1.2.1.75.1.2.3.1.6) A variable indicating that the attached NxPort has requested the FxPort for the support of Intermix and the FxPort has granted the request.
Class 1 or loop connection. If this FxPort is not engaged in a connection, then the value of this object is 000000H. Syntax FcAddressId Access Read-only Status Current Return value Unsupported fcFxPortBbCreditModel (1.3.6.1.2.1.75.1.2.3.1.12) This object identifies the BB_Credit model used by the FxPort. Syntax FcBbCreditModel HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 155...
Access Read-write Status Current Return value Returns alternate(2). Writes not supported. The Error group The objects described in this section are in table format, indexed by switch index and port index. An example of how to access one of these objects is: snmpget localhost public fcFxPortLinkFailures.1.1.
Current Return value The total number of InvalidCRCs encountered for the port fcFxPortDelimiterErrors (1.3.6.1.2.1.75.1.3.1.1.7) The number of delimiter errors detected by this FxPort Syntax Counter32 HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 157...
Access Read-only Status Current Return value Unsupported. Always returns error status NoSuchName. fcFxPortAddressIdErrors (1.3.6.1.2.1.75.1.3.1.1.8) The number of address identifier errors detected by this FxPort Syntax Counter32 Access Read-only Status Current Return value The total number of InvDestAddrs encountered for the port fcFxPortLinkResetIns (1.3.6.1.2.1.75.1.3.1.1.9) The number of Link Reset Protocols received by this FxPort from the attached NxPort Syntax...
Unsupported. Always returns error status NoSuchName. fcFxPortC1OutFrames (1.3.6.1.2.1.75.1.4.1.1.2) The number of Class 1 frames (other than Class 1 connectrequest) delivered through this FxPort to its attached NxPort. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 159...
Syntax Counter32 Access Read-only Status Current Return value Unsupported. Always returns error status NoSuchName. fcFxPortC1InOctets (1.3.6.1.2.1.75.1.4.1.1.3) The number of Class 1 frame octets, including the frame delimiters, received by this FxPort from its attached NxPort. Syntax Counter32 Access Read-only Status Current Return value Unsupported.
(1.3.6.1.2.1.75.1.4.1.1.9) The number of Class 1 connections successfully established in which the attached NxPort is the destination of the connectrequest. Syntax Counter32 Access Read-only HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 161...
Status Current Return value Unsupported. Always returns error status NoSuchName. fcFxPortC1ConnTime (1.3.6.1.2.1.75.1.4.1.1.10) The cumulative time that this FxPort has been engaged in Class 1 connection. The amount of time is counted from after a connectrequest has been accepted until the connection is disengaged, either by an EOFdt (End of Frame—Disconnect Terminate) or Link Reset.
Current Return value The total number of Class2Toss discarded by the port. fcFxPortC2FbsyFrames (1.3.6.1.2.1.75.1.4.2.1.6) The number of F_BSY frames generated by this FxPort. Syntax Counter32 HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 163...
Access Read-only Status Current Return value The total number of FBSY frames generated by this port for Class 2 and Class 3 frames. fcFxPortC2FrjtFrames (1.3.6.1.2.1.75.1.4.2.1.7) The number of F_RJT frames generated by this FxPort against Class 2 frames. Syntax Counter32 Access Read-only Status...
The Capability group consists of a table describing information about what each FxPort is inherently capable of operating or supporting. A capability may be used as expressed in its respective object value in the Configuration group. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 165...
fcFxPortCapFcphVersionHigh (1.3.6.1.2.1.75.1.5.1.1.1) The highest or most recent version of FC-PH that the FxPort is capable of supporting. Syntax FcphVersion Access Read-only Status Current Return value Always returns 32 (0x20) fcFxPortCapFcphVersionLow (1.3.6.1.2.1.75.1.5.1.1.2) The lowest or earliest version of FC-PH that the FxPort is capable of supporting. Syntax FcphVersion Access...
A flag indicating whether or not the FxPort is capable of supporting the intermixing of Class 2 and Class 3 frames during a Class 1 connection. This flag is only valid if the port is capable of supporting Class 1 service. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 167...
Syntax TruthValue Access Read-only Status Current Return value Always returns False(2) fcFxPortCapStackedConnMode (1.3.6.1.2.1.75.1.5.1.1.9) A value indicating the mode of Stacked Connect request that the FxPort is capable of supporting. Syntax FcStackedConnMode Access Read-only Status Current Return value Always returns None(1) fcFxPortCapClass2SeqDeliv (1.3.6.1.2.1.75.1.5.1.1.10) A flag indicating whether or not the FxPort is capable of supporting Class 2 sequential delivery.
The minimum holding time that the FxPort is capable of supporting, in microseconds. Syntax MicroSeconds Access Read-only Status Current Return value Returns the value 10 (0x0A) HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 169...
This MIB replaces the fcFxPortPhystable module defined in FIBRE-CHANNEL-FE-MIB, and defines volatile control objects for ports in an SN6000 or 8/20q Fibre Channel Switch. If the switch gets reset, these values revert back to the default values in the configuration file.
fcQxPortPhysOperStatus (1.3.6.1.4.1.1663.1.3.10.1.1.4) The current operational status of the FxPort. The testing(3) status indicates that no operational frames can be passed. • If fcQxPortPhysAdminStatus is offline(2), then fcQxPortPhysOperStatus should be offline(2). • If fcQxPortPhysAdminStatus is changed to online(1), then fcQxPortPhysOperStatus should change to online(1). •...
The FD-MIB enables you to download, install, and activate new firmware on an HP StorageWorks SN6000 or 8/20q Fibre Channel Switch using the Trivial File Transfer Protocol (TFTP). The downloaded firmware can be activated using a hot reset (non-disruptive) or a hard reset (disruptive).
Access Read-write Status Current qlgcChFwDwldHostAddrType (1.3.6.1.4.1.3873.3.1.1.2.3) The type of the IP address from which the firmware file is accessed Syntax INTEGER Access Read-write Status Current qlgcChFwDwldHostAddr (1.3.6.1.4.1.3873.3.1.1.2.4) The IP address from which the firmware file is accessed Syntax IP ADDRESS Access Read-write Status...
The value for the type of reset (hot reset or hard reset) Syntax INTEGER { (1)–Normal (disruptive) (2)–NDCLA (Non-Disruptive Code Load Activation) Access Read-write Status Current HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 177...
Indicates that failure to follow directions could result in damage to equipment or data. IMPORTANT: Provides clarifying information or specific instructions. NOTE: Provides additional information. TIP: Provides helpful hints and shortcuts. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 179...
HP StorageWorks 8Gb Simple SAN Connection Kit Quick Start Instructions • HP StorageWorks Simple SAN Connection Manager User Guide • HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Rack Mount Kit Quick Start Installation Instructions • HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Quick Start Installation Instructions •...
For more information about the HP Customer Self Repair program, contact your local service provider. For the North American program, visit the HP website (http://www.hp.com/go/selfrepair). HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Simple Network Management Protocol Reference Guide 181...