PDG-DWL2500 Expand Serial Command Functional Specifications Overview 1.1 This Functional Specification defines communication functions for PDG-DWL2500. 1.2 Compatible to Firmware Ver. 1.x of the projector. 1.3 Most commands can be used to control projector remotely from PC by RS-232C. Therefore, the commands are defined as Expand Serial Commands.
PDG-DWL2500 Expand Serial Command Functional Specifications Notes for communication 1. Expand Serial Command is defined as one command / one line that starts with “C” and ends with carriage return (0x0D) 2. There are two types of commands: Functional Execution Command and Status Read Command.
PDG-DWL2500 Expand Serial Command Functional Specifications 5. Functional Execution Command Table 5.1 Image Command Table Execute command Item CF_BRIGHT_%1[CR] Set Brightness value CF_CONT_%1[CR] Set Contrast value CF_COLOR_%1[CR] Set Color value CF_TINT_%1[CR] Set Tint value CF_SHARP_%1[CR] Set Sharpness value CF_GAMMA_%1[CR] Set Gamma value CF_WBAL-R_%1[CR] Set White Balance Red value CF_WBAL-G_%1[CR]...
PDG-DWL2500 Expand Serial Command Functional Specifications 5.4 Screen Command Table Execute command Item CF_SCREEN_%1[CR] Select Screen size CF_DZCENT_%1[CR] Cancel Digital Zoom mode CF_KEYSTONE_%1[CR] Set Keystone CF_KYSTNMODE_%1[CR] Set Keystone Store mode CF_VSCALE_%1[CR] Set value of Vertical scale CF_VPOS_%1[CR] Set value of Vertical position CF_HSCALE_%1[CR] Set value of Horizontal scale CF_HPOS_%1[CR]...
PDG-DWL2500 Expand Serial Command Functional Specifications CF_FILH_%1[CR] Reset Filter used time CF_FDEFAULT_%1[CR] Set the value to Factory Default 5.8 Other Command Table Execute command Item Behave the same as corresponding key of the projector / CF_KEYEMU_%1[CR] remote control. CF_MENU_%1[CR] Switch ON/OFF of each Menu. CF_POWER_%1[CR] Switch ON/OFF of Power.
PDG-DWL2500 Expand Serial Command Functional Specifications 6. Status Read Command Table 6.1 Image Status Read Command Table Status read command Item CR_BRIGHT[CR] Get Brightness value CR_CONT[CR] Get Contrast value CR_COLOR[CR] Get Color value CR_TINT[CR] Get Tint value CR_SHARP[CR] Get Sharpness value CR_GAMMA[CR] Get Gamma value CR_WBAL-R[CR]...
PDG-DWL2500 Expand Serial Command Functional Specifications 6.5 Screen Status Read Command Table Status read command Item CR_SCREEN[CR] Get selected screen size CR_KYSTNMODE[CR] Get setting status of Keystone Store mode CR_VSCALE[CR] Get setting status of Vertical Scale CR_VPOS[CR] Get setting status of Vertical Position CR_HSCALE[CR] Get setting status of Horizontal Scale CR_HPOS[CR]...
PDG-DWL2500 Expand Serial Command Functional Specifications CR_FANMODE[CR] Get selected Fan mode CR_FANCONTROL[CR] Get selected Fan Control Mode CR_FILH[CR] Get Filter used time CR_FILREPL[CR] Get the information for Filter replacement time CR_FILTIMER[CR] Get time when Filter warning OSD is displayed 6.9 Other Status Read Command Status read command Item CR_STATUS[CR]...
PDG-DWL2500 Expand Serial Command Functional Specifications 7. Error Code Table Error Code Details -When the received data cannot be decoded -Parameter determination error (digit number error, including invalid value, etc.) When the function selected is not available under current condition. ex) When receiving signal-related commands while no signal is entered Selected value is out of range (Not reflected) Command mismatched to Hardware (command for Optional function...
PDG-DWL2500 Expand Serial Command Functional Specifications 8. Functional Execution Command 8.1 Format PC issues commands in format as below: Pattern1 : “CF_COMMAND” [CR] Pattern2 : “CF_COMMAND_”%1 [CR] CF_ : Header COMMAND : Character line %1 : Parameter (Character line) _ : Space (To separate COMMAND and Parameter) The projector decodes the received command and when it is ready to receive the next command, it returns the response.
PDG-DWL2500 Expand Serial Command Functional Specifications 8.4 Image Command 8.4.1 CF_BRIGHT Command Command "CF_BRIGHT_%1”[CR] "000~063” --------------- Directly select Brightness setting value "UP” ----------------------- Current Brightness setting value + 1 "DN” ----------------------- Current Brightness setting value – 1 Set Brightness value of user control The value set by this command will not be saved to projector.
PDG-DWL2500 Expand Serial Command Functional Specifications 8.4.5 CF_SHARP Command Command “CF_SHARP_%1”[CR] “000~015” ---------------- Directly select Sharpness setting value “UP” ------------------------ Current Sharpness setting value + 1 “DN” ------------------------ Current Sharpness setting value - 1 Set Sharpness value of user control The value set by this command will not be saved to projector.
PDG-DWL2500 Expand Serial Command Functional Specifications 8.4.8 CF_COLTEMP Command Command “CF_COLTEMP_%1”[CR] “000” ------ Xlow “001” ------ Low “002” ------ Mid “003” ------ High Set Color Temperature. (Available only in the normal Power ON status) The value set by this command will not be saved to the projector. Therefore, when Details turning into Standby status or ALL is OFF, the value returns to original setting.
PDG-DWL2500 Expand Serial Command Functional Specifications 8.4.11 CF_IMAGE Command Command “CF_IMAGE_%1”[CR] “DYNAMIC” ------ Dynamic (Fixed value to enable projection with a sharp, powerful picture tone) “STAND” ---------- Standard (Image adjust value is set to factory default) “REAL” ------------ Real (Fixed value to display graphic image with natural tone) “CINEMA”...
PDG-DWL2500 Expand Serial Command Functional Specifications 8.5 PC Adjust Control Command 8.5.1 CF_FSYNC Command Command “CF_FSYNC_%1”[CR] “0000~0031” --------------- Directly select Fine Sync setting value “UP” -------------------------- Current Fine Sync setting value + 1 “DN” -------------------------- Current Fine Sync setting value - 1 Set Fine Sync value of PC signal The value set by this command will not be saved to projector.
PDG-DWL2500 Expand Serial Command Functional Specifications 8.5.4 CF_H – POS Command Command “CF_H-POS_%1”[CR] “0000~nnnn” --- Directly select Horizontal Position setting value “nnnn” shows maximum value, it is current Total Dots value - Display Dots value “UP” -------------- Current Horizontal Position setting value + 1 “DN”...
Page 24
PDG-DWL2500 Expand Serial Command Functional Specifications “MODE8” ------ Set Mode8 to Free status “MODE9” ------ Set Mode9 to Free status “MODE10” ---- Set Mode10 to Free status Delete the registered data in Mode1-Mode5 and turns it to Free status. This command operates the same as turning Mode1-Mode5 to Free in PC Adjust Details Menu.
PDG-DWL2500 Expand Serial Command Functional Specifications 8.6.2 CF_SOURCE Command Command “CF_SOURCE_%1”[CR] “ANALOG” --------- Select Analog Input “YPBPR” ----------- Select Component Input “SCART” ----------- Select Scart Input Input is ”UP” ---------------- The same operation as pressing Up key or Left Computer 1 ”DN”...
PDG-DWL2500 Expand Serial Command Functional Specifications 8.6.5 CF_INPUT3 Command Command “CF_INPUT3_%1_”[CR] “HDMI” ------------------ Select HDMI Select HDMI Input and source specified in %1 at once. Details This command is available in normal Power ON status. Acceptable “000”[CR] Response Unacceptable “Error Code”[CR] 8.6.6 CF_INPUT4 Command Command...
PDG-DWL2500 Expand Serial Command Functional Specifications 8.7.3 CF_KEYSTONE Command Command “CF_KEYSTONE_%1”[CR] “UP” ------------- Correct Keystone distortion to reduce upper part of image “FUP” ----------- Correct Keystone distortion to reduce upper part by 2steps “DN” ------------- Correct Keystone distortion to reduce lower part of image “FDN”...
PDG-DWL2500 Expand Serial Command Functional Specifications 8.8 Lamp Command 8.8.1 CF_LAMPH Command Command “CF_LAMPH_%1”[CR] “RST” Reset Lamp use time counter. Details This command is available in normal Power ON status. Acceptable “000”[CR] Response Unacceptable “Error Code”[CR] 8.8.2 CF_LAMPMODE Command Command “CF_LAMPMODE_%1”[CR] “NORMAL”...
PDG-DWL2500 Expand Serial Command Functional Specifications 8.9 Sound Command 8.9.1 CF_VOLUME Command Command “CF_VOLUME_%1”[CR] “000-063” -------------------------- Directly select Volume setting value “UP” --------------------------------- Current Volume setting value +1 “DN” --------------------------------- Current Volume setting value -1 Control Volume value The same operation of Volume Up/Down as projector and RC, and directly select Volume setting value.
PDG-DWL2500 Expand Serial Command Functional Specifications 8.10.3 CF_AUTOSETUPPCADJ Command Command “CF_AUTOSETUPPCADJ_%1”[CR] “ON” ------------------- Set Auto PC ADJ. function to ON “OFF” ------------------ Set Auto PC ADJ. function to OFF Set/Cancel Auto PC adj. function This command is available in normal Power ON status. Details Note) It is unable to set both PC ADJ.
PDG-DWL2500 Expand Serial Command Functional Specifications “1” ------------------- Select 1 “2” ------------------ Select 2 Setup 3D Sync. The status set by this command is stored in EEPROM and its setting is effective Details after ALL is OFF. This command is available in normal Power ON status. Acceptable “000”[CR] Response...
PDG-DWL2500 Expand Serial Command Functional Specifications The status set by this command is stored in EEPROM and the setting remains even after the power is turned to ALL OFF status. *When ÿ 1=”USER” is received, error code “101” is returned, in the case of Capture non-practice.
PDG-DWL2500 Expand Serial Command Functional Specifications “NORMAL” -------------------------- Select Normal mode “ENHANCED” ---------------------- Select Enhanced mode Select image mode of HDMI setup. The status set by this command is stored in EEPROM and its setting is effective Details after ALL is OFF This command is available in normal Power ON status.
PDG-DWL2500 Expand Serial Command Functional Specifications after ALL is OFF This command is available in normal Power ON status. Acceptable “000”[CR] Response Unacceptable “Error Code”[CR] 8.10.19 CF_P-MANETIME Command Command “CF_P-MANETIME_%1”[CR] “01” ~ ”30” ----------------------- Directly select setting time by the minute “UP”...
PDG-DWL2500 Expand Serial Command Functional Specifications “WHITE” -------- Select White Select color of Closed caption. The status set with this command is stored in EEPROM and its setting is effective even after ALL is OFF. Details This command is available in normal Power ON status. Note)Closed caption is available under conditions below;...
PDG-DWL2500 Expand Serial Command Functional Specifications Acceptable “000”[CR] Response Unacceptable “Error Code”[CR] 8.10.26 CF_FANMODE Command Command “CF_FANMODE_%1”[CR] “L1” ---------------------------- Set Fan Mode to L1 “L2” ---------------------------- Set Fan Mode to L2 Switch Fan Mode When L1 is selected, fan noise after POWER OFF is louder. When L2 is selected, fan noise after POWER OFF becomes quiet.
PDG-DWL2500 Expand Serial Command Functional Specifications 8.10.30 CF_FDEFAULT Command Command “CF_FDEFAULT_%1”[CR] “RST” Set the value to Factory Default Details This command is available in normal Power ON status. Acceptable “000”[CR] Response Unacceptable “Error Code”[CR] 43/72...
PDG-DWL2500 Expand Serial Command Functional Specifications 8.11 Other Command 8.11.1 CF_KEYENU Command Command “CF_KEYENU_%1”[CR] “RIGHT” ------------------------- Shift Pointer on OSD Menu to right “LEFT” --------------------------- Shift Pointer on OSD Menu to left “UP” ------------------------------ Shift Pointer on OSD Menu to right “DN”...
PDG-DWL2500 Expand Serial Command Functional Specifications 8.11.4 CF_FREEZE Command Command “CF_FREEZE_%1”[CR] “ON” ------------------------ Set Freeze to ON “OFF” ----------------------- Set Freeze to OFF “UP” ------------------------------ Switch setting (On → Off → On → ÿ e ÿ e ÿ e ) “DN”...
PDG-DWL2500 Expand Serial Command Functional Specifications 9. Status Read Command 9.1 Format PC issues commands in format as below: “CR_Command” [CR] Command: Character Line When projector receives the appropriate command, it returns a character line as the required data “000ÿ ? ”%1 [CR] %1: Required Data (Character Line.
PDG-DWL2500 Expand Serial Command Functional Specifications 9.4 Image Status Read Command 9.4.1 CR_BRIGHT Command Command “CR_BRIGHT”[CR] Details Get Brightness value of user control Acceptable “000_ÿ ÿ A ”[CR] Response “000”~“063” Unacceptable “Error code”[CR] 9.4.2 CR_CONT Command Command “CR_CONT”[CR] Details Get Contrast value of user control Acceptable “000_ÿ...
PDG-DWL2500 Expand Serial Command Functional Specifications 9.4.6 CR_GAMMA Command Command "CR_GAMMA”[CR] Details Get Gamma value of user control Acceptable “000_%a”[CR] “DFLT” -------------------------- Default is selected. “18” ------------------------------ 1.8 is selected. “20” ------------------------------ 2.0 is selected. Response “22” ------------------------------ 2.2 is selected. “24”...
PDG-DWL2500 Expand Serial Command Functional Specifications 9.5 PC Adjust Status Read Command 9.5.1 CR_FSYNC Command Command "CR_FSYNC”[CR] Details Get Fine Sync value Acceptable “000_%a”[CR] Response “0000”~“0031” Unacceptable “Error Code”[CR] 9.5.2 CR_TDOTS Command Command “CR_TDOTS”[CR] Details Get Total Dots value Acceptable “000_%a”[CR] “nnnn”~“mmmm”...
PDG-DWL2500 Expand Serial Command Functional Specifications 9.5.6 CR_PCSTORE Command Command “CR_PCSTORE”[CR] Get Free/Stored status of MODE1 – MODE10 for PC Adjust Details The data consists of 10 bytes and each byte indicates the status of MODE1 ~ MODE10 respectively. (F:Free S:Stored) Acceptable “000_%a”[CR] “FFFFFFFFFF”...
PDG-DWL2500 Expand Serial Command Functional Specifications 9.6 Video Status Read Command 9.6.1 CR_SERSYS Command Command “CR_SERSYS”[CR] Get currently selected signal Details Returns auto-detected signal in Auto mode Only available for Video input. (N/A when Input is computer) Acceptable “000_%1”[CR] “1080P60” -------------- 1080p 60Hz “1080P50”...
PDG-DWL2500 Expand Serial Command Functional Specifications 9.7.9 CR_SYSLIST Command Command “CR_SYSLIST”[CR] Details Get selectable System titles Acceptable “000_%1_%2_..._%x” [CR] - When Input is PC-Analog “XGA1” ------------ XGA1is selectable “1080I ” ----------- 1080i is selectable Projector does not return Auto, Mode 1-10 When there is no signal, it returns Error Code “101”...
PDG-DWL2500 Expand Serial Command Functional Specifications 9.9 Lamp Status Read Command 9.9.1 CR_LAMPREPL Command Command “CR_LAMPREPL”[CR] Details Get information of Lamp Replacement time Acceptable “000_%1”[CR] “1Y” -------------------------- Over lamp replacement time “1N” -------------------------- Within lamp replacement time “1” means the number of lamps. Response (1 lamp model→...
PDG-DWL2500 Expand Serial Command Functional Specifications 9.9.5 CR_LAMPMSTS Command Command “CR_LAMPSTS”[CR] Details Get Lighting status of lamp Acceptable “000_%1”[CR] “ÿ N **** ” A number of * should be among 1-4. First character shows how many lamps are incorporated in projector.
PDG-DWL2500 Expand Serial Command Functional Specifications 9.10 Sound Status Read Command 9.10.1 CR_VOLUME Command Command “CR_VOLUME”[CR] Details Get Volume value of user control Acceptable “000_%a”[CR] Response “000”~“063” Unacceptable “Error code”[CR] 9.10.2 CR_MUTE Command Command “CR_MUTE”[CR] Details Get sound mute setting status Acceptable “000_%a”[CR] “ON”...
PDG-DWL2500 Expand Serial Command Functional Specifications 9.11.4 CR_ÿ DSET Command Command “CR_3DSET”[CR] Details Get setting status of 3D function Acceptable “000_%a”[CR] “ON” --------------------- On is selected Response “OFF” ---------------------Off is selected Unacceptable “Error Code”[CR] 9.11.5 CR_3DSYNC Command Command “CR_3DSYNC”[CR] Details Get setting status of 3D Sync Acceptable “000_%a”[CR]...
PDG-DWL2500 Expand Serial Command Functional Specifications 9.11.9 CR_BACKGND Command Command “CR_BACKGND” [CR] Details Get setting status of Screen for no signal Acceptable “000_%1” [CR] “BLUE” -------------------------------- Blue Back is selected Response “USER” ------------------------------- User is selected “BLACK” ------------------------------ Black Back is selected Unacceptable “Error Code”...
PDG-DWL2500 Expand Serial Command Functional Specifications 9.11.24 CR_PJLOCKNOW Command Command “CR_PJLOCKNOW” [CR] Details Get if PJ lock is actually in operation Acceptable “000_%1[CR] “LOCK” ------------- PJ Lock is in operation. PJ Lock status is ON-1 or ON-2 on Menu, and PJ PIN CODE is not entered so that projector is actually locked.
PDG-DWL2500 Expand Serial Command Functional Specifications 9.11.29 CR_FILREPL Command Command “CR_FILREPL”[CR] Details Get the information of Filter replacement time Acceptable “000_%1”[CR] “1Y” ------------------- Over filter replacement time Response “1N” ------------------ Within filter replacement time Unacceptable “Error Code”[CR] 9.11.30 CR_FILTIMER Command Command “CR_FILTIMER”...
PDG-DWL2500 Expand Serial Command Functional Specifications 9.12 Other Status Read Command 9.12.1 CR_STATUS Command Command “CR_STATUS”(CR) Get status of Projector behavior. Details This command affects the same as ”CR0” of Basic Serial command, but this has an error code. Acceptable “000_%1”[CR] “00”= Power ON “80”= Stand by...
PDG-DWL2500 Expand Serial Command Functional Specifications 9.12.7 CR_TEMP Command Command "CR_TEMP”[CR] Get current temperature inside a projector. Details If there are several sensors installed, it is possible to get information from all the sensors at once. Acceptable “000_%1_%2_%3”[CR] %1= Sensor 1 temperature (Outside temperature) %2= Sensor 2 temperature (Inside temperature1) %3= Sensor 3 temperature (Inside temperature2) %1,%2 are consists of 6 bites fixed...
PDG-DWL2500 Expand Serial Command Functional Specifications 9.12.8 CR_TEMPFAIL Command Command "CR_TEMPFAIL”[CR] Get the temperature inside a projector when abnormal temperature occurs. Details If there are several sensors installed, it is possible to get information from all the sensors at once. Acceptable “000_%a_%b_%c”[CR] %a ------------------ Sensor 1 temp.