HP 2000fc User Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Storage
  5. StorageWorks 2000fc
  6. User manual
HP 2000fc User Manual

HP 2000fc User Manual

Modular smart array
Hide thumbs Also See for 2000fc:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Reference Manual, User Manual
HP StorageWorks
2012fc Modular Smart Array

user guide

Part number: 481597-001
First edition: March, 2008

Advertisement

Table of Contents
loading

Related Manuals for HP 2000fc

Summary of Contents for HP 2000fc

  • Page 1: User Guide

    HP StorageWorks 2012fc Modular Smart Array user guide Part number: 481597-001 First edition: March, 2008...
  • Page 2 © Copyright 2008 Hewlett-Packard Development Company, L.P. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.

  • Page 3: Table Of Contents

    Contents About This Guide ........... 7 Intended Audience .
  • Page 4 Installing and Cabling Enclosures ........25 Required Tools .
  • Page 5 Configuring a System for the First Time ....... 49 Setting Management Port IP Addresses Using the CLI .
  • Page 6 HP StorageWorks 2012fc Modular Smart Array user guide • March 2008...

  • Page 7: About This Guide

    About This Guide Intended Audience This guide is intended for use by system administrators and information professionals who are experienced with the following: Direct attach storage (DAS) or storage area network (SAN) management ■ Network administration ■ Network installation ■ Storage system installation and configuration, including installing an HP rack ■...

  • Page 8: Document Conventions

    Document Conventions Typeface Meaning Examples AaBbCc123 Book title, new term, or See the Release Notes. emphasized word A virtual disk (vdisk) can ..You must be an advanced user to ..Directory or file name, The default file name is store.logs. AaBbCc123 value, command, or The default IP address is 10.0.0.1.

  • Page 9: Hp Technical Support

    HP Technical Support Telephone numbers for worldwide technical support are listed on the HP support website: http://www.hp.com/support Collect the following information before calling: Technical support registration number (if applicable) ■ Product serial numbers ■ Product model names and numbers ■ Applicable error messages ■...

  • Page 10: Subscription Service

    Subscription Service HP strongly recommends that customers sign up online using the Subscriber's choice website: http://www.hp.com/go/e-updates Subscribing to this service provides you with e-mail updates on the latest product enhancements, newest versions of drivers, and firmware documentation updates as well as instant access to numerous other product resources. HP Websites For other product information, see the following HP websites: http://www.hp.com...

  • Page 11: Before You Begin

    CH A P T E R Before You Begin The MSA2000 Family 2012fc Modular Smart Array and MSA2000 Drive Enclosure are high-performance storage solutions that combine outstanding performance with high reliability, availability, flexibility, and manageability. Supported configurations include a controller enclosure with or without attached drive enclosures.

  • Page 12: System Management Software

    System Management Software Embedded management software includes a web-browser interface and the command-line interface described below. HP StorageWorks MSA2000 Family Storage Management Utility (SMU) SMU is the primary interface for configuring and managing the system. A web server resides in each controller module. SMU enables you to manage the system from a web browser that is properly configured and that can access a controller module through an Ethernet connection.

  • Page 13: Hardware Components And Leds

    Hardware Components and LEDs This section describes the main hardware components of your storage system enclosures. Controller Enclosure Components and LEDs The controller enclosure can be connected to Fibre Channel host bus adapters (HBAs) or switches. Table 1-1 describes the controller enclosure components. Table 1-1 Controller Enclosure Components Description Quantity...
  • Page 14 Figure 1-1 shows the LEDs on the front of a controller. Enclosure ID Drive module LEDs (top to bottom) Status LEDs (top to bottom): Fault/UID Fault ID Online/activity Heartbeat Drive modules are numbered by column top to bottom: 0–2, 3–5, 6–8, 9–11 Figure 1-1 Controller (Front View) Table 1-2 describes the LEDs on the front of a controller.
  • Page 15 Table 1-3 describes the LEDs on the drive module. Table 1-3 Drive Module LED Combinations (Front) Online/Activity Fault/UID (green) (amber/blue) Description The drive is online, but it is not currently active. Blinking The drive is active and operating normally. irregularly Amber, blinking Offline;...
  • Page 16 Figure 1-2 shows the ports and switches at the back of the controller. Power switch LINK SPEED LINK SPEED Service Port 0 Port 1 DIRTY CLEAN CACHE ACTIVITY 10/100 BASE-T STATUS LINK SPEED LINK SPEED Service Port 0 Port 1 DIRTY CLEAN CACHE...
  • Page 17 Figure 1-3 shows the LEDs at the back of the controller. AC Power Good DC Voltage/Fan Fault/ Host link status Cache status Expansion port status Service Required Host link speed Host activity LINK SPEED LINK SPEED Service Port 0 Port 1 DIRTY CLEAN CACHE...
  • Page 18 Table 1-5 Controller LEDs (Back) (Continued) Location Color State Description Unit Locator Controller White Normal operation. module Blink Physically identifies the controller module. Controller OK to Blue The controller module is not prepared for removal. module Remove The controller module can be removed. Controller Fault/Service Amber...

  • Page 19: Drive Enclosure Components And Leds

    Drive Enclosure Components and LEDs A drive enclosure can be connected to a controller enclosure or to another drive enclosure to provide additional disk storage capacity. Table 1-6 describes the drive enclosure components. Table 1-6 Drive Enclosure Components Description Quantity Expansion (I/O) module 1 or 2 SAS or SATA drive module...
  • Page 20 Figure 1-4 shows the ports and switches at the back of the drive enclosure. Power switch Service Service SAS In port Service port SAS Out port Figure 1-4 Drive Enclosure Ports and Switches (Back View) Table 1-7 describes the ports and switches on the back of the drive enclosure. Table 1-7 Drive Enclosure Ports and Switches (Back) Location Port/Switch...
  • Page 21 Figure 1-5 shows the LEDs at the back of the drive enclosure. AC Power Good DC Voltage/Fan Fault/ SAS In port status SAS Out port status Service Required Service Service Unit Locator OK to Remove Fault/Service Required Figure 1-5 Drive Enclosure LEDs (Back View) Table 1-8 describes the LEDs on the back of the drive enclosure.
  • Page 22 Table 1-8 Drive Enclosure LEDs (Back) (Continued) Location Color State Description Expansion Fault/Service Amber A fault has been detected or a service action is module Required required. Blink Indicates a hardware-controlled power up or a cache flush or restore error. Expansion Green Expansion module is not OK.

  • Page 23: Installation Checklist

    Installation Checklist Table 1-9 outlines the steps required to install the enclosures and initially configure the system. To ensure a successful installation, perform the tasks in the order they are presented. Table 1-9 Installation Checklist Step Installation Task Where to Find Procedure Prepare the rack for installation.
  • Page 24 HP StorageWorks 2012fc Modular Smart Array user guide • March 2008...

  • Page 25: Installing And Cabling Enclosures

    CH A P T E R Installing and Cabling Enclosures This chapter describes how to install and cable enclosures in a standard 19-inch EIA rack cabinet. It contains the following sections: “Required Tools” on page 25 ■ “Safety Precautions” on page 26 ■...

  • Page 26: Safety Precautions

    Safety Precautions For your protection, observe the following safety precautions when setting up your equipment: Follow all cautions and instructions marked on the equipment. ■ Ensure that the voltage and frequency of your power source match the voltage ■ and frequency inscribed on the equipment’s electrical rating label. Never push objects of any kind through openings in the equipment.

  • Page 27: Installing Enclosures Into A Rack

    Installing Enclosures Into a Rack This section describes how to install the enclosures into a standard 19-inch rack cabinet with a 28 to 36-inch (71.12 to 91.44-cm) depth. Tip – Keep all hardware items in plastic bags until you are ready to use them. This enables you to correctly identify the screws and avoid confusion.

  • Page 28: Rack Installation Overview And Procedure

    Rack Installation Overview and Procedure Figure 2-1 provides a visual overview of rack installation and components and corresponds to the steps that follow. #10-32 x 5/8-in. Truss screws (Step 6) #10-32 x 5/8-in. Truss screws Rear bracket connected to rack (Step 9) Threaded PEMs (4) Side bracket...
  • Page 29 Use the following procedure and refer to Figure 2-1 to install each enclosure into the rack. When positioning an enclosure in the rack, do not block the air vents at the front or back of the enclosure. Caution – If you only have one person to perform the installation, remove the power and cooling modules and drive modules from an enclosure before installation, and use the optional nylon front support brackets.
  • Page 30 Figure 2-2 Side Bracket With Alignment Marks b. On one side, insert the first two screws through the side bracket slots above and below the alignment mark into the rear-most threaded holes in the enclosure. For example, to mount the enclosure in a 28-inch deep rack, position the side bracket so that the 28-inch alignment mark is aligned with the rear-most threaded holes in the enclosure.

  • Page 31: Attaching The Ear Caps

    Attaching the Ear Caps The plastic ear caps are snap-on parts that require some care when attaching or removing them. After the enclosure has been installed in the rack cabinet, attach the ear caps, which are located in a plastic bag included in the controller enclosure package.

  • Page 32: Connecting Controller And Drive Enclosures

    Connecting Controller and Drive Enclosures Use the supplied SAS cables to connect a controller enclosure to up to three drive enclosures. Figure 2-4 and Figure 2-5 show the recommended fault-tolerant cabling patterns. In an enclosure, the upper module is designated A and the lower module is designated B.
  • Page 33 Controller A Controller B Figure 2-5 Fault-Tolerant Cabling Connections Between One Controller Enclosure and Up to Three Drive Enclosures Chapter 2 Installing and Cabling Enclosures...
  • Page 34 Controller A Controller B Figure 2-6 Non-Fault-Tolerant Cabling Connections Between One Controller and Up to Three Drive Enclosures HP StorageWorks 2012fc Modular Smart Array user guide • March 2008...

  • Page 35: Connecting Ac Power

    Connecting AC Power Use this procedure to connect AC power to the enclosures. 1. Verify that both power switches are off. 2. Using the AC power cords, for each enclosure, connect one power and cooling module to one power source in the rack, and the other power and cooling module to a separate power source in the rack.

  • Page 36: Testing The Enclosure Connections

    Testing the Enclosure Connections Use this procedure to power on the newly installed system. 1. Press the power switches at the back of each drive enclosure to the On ( –) position. This ensures that the disks in the enclosures have enough time to completely spin up before being scanned by the RAID modules in the controller enclosure.

  • Page 37: Correcting Enclosure Ids

    Correcting Enclosure IDs When installing a system with drive enclosures attached, the enclosure IDs might not agree with the physical cabling order. This is because the controller might have been previously attached to some of the same enclosures and it attempts to preserve the previous enclosure IDs if possible.
  • Page 38 HP StorageWorks 2012fc Modular Smart Array user guide • March 2008...

  • Page 39: Connecting Hosts

    CH A P T E R Connecting Hosts This chapter describes how to connect data and management hosts to controller enclosures. It contains the following sections: “Host System Requirements” on page 39 ■ “Configuration Considerations” on page 40 ■ “Connecting Direct Attach Configurations” on page 42 ■...

  • Page 40: Installing The Msa2000 Family Ses Driver For Microsoft Windows Hosts

    Installing the MSA2000 Family SES Driver for Microsoft Windows Hosts Installing the MSA2000 Family SCSI Enclosure Services (SES) driver prevents Microsoft Windows hosts from displaying the Found New Hardware Wizard when the storage system is discovered. 1. Download MSA2000 Family SCSI Enclosure Services (SES) driver package from the .

  • Page 41: Using Host Port Interconnects

    Using Host Port Interconnects When the internal connections between host ports are enabled through SMU, host port 0 on each controller is internally connected to host port 1 on the other controller. This provides redundancy in the event one controller fails (failover) by making volumes owned by the failed controller accessible on the surviving controller.

  • Page 42: Connecting Direct Attach Configurations

    Connecting Direct Attach Configurations This section explains how to connect the controller enclosure directly to data hosts. It shows configurations that support high availability and high performance, and notes when host port interconnects must be enabled. The controller enclosure has four host connections, two per controller. Connect FC cables from host ports on each controller to FC HBAs on data hosts, as shown in the following figures.
  • Page 43 Figure 3-2 shows a single-controller to two single-port data hosts configurtion.Figure shows a single-controller to a single-port data host configuration. Figure 3-2 Single-Controller, Direct Attach Connection to Two Single-Port Data Hosts Figure 3-3 shows the preferred redundant configuration. This configuration requires that host port interconnects are enabled as described in “Configuring Host Ports”...
  • Page 44 Figure 3-4 shows a non-redundant configuration that can be used when high performance is more important than high availability. This configuration requires host port interconnects to be disabled, which they are by default. Controller A Controller B Figure 3-4 High-Performance, Dual-Controller, Direct Attach Connection to Two Dual-Port Data Hosts (Not Fault Tolerant) HP StorageWorks 2012fc Modular Smart Array user guide •...

  • Page 45: Connecting Switch Attach Configurations

    Connecting Switch Attach Configurations This section explains how to connect the controller enclosure to data hosts through one or more external FC switches. The controller enclosure has four host connections, two per controller. Connect FC cables from controller hosts ports to switch ports, and from switch ports to data hosts, as shown in the following figures.

  • Page 46: Connecting One Data Host Through One Switch

    Connecting One Data Host Through One Switch Figure 3-5 shows a dual-controller connection through one switch to one dual-port data host with two FC HBA ports. This configuration requires that host port interconnects are disabled, which they are by default. It also requires host-based multipathing software.

  • Page 47: Connecting Two Data Hosts Through Two Switches

    Connecting Two Data Hosts Through Two Switches Figure 3-6 shows the preferred high-availability dual-controller connection through two switches to two dual-port data hosts, in which each data host has two FC HBA ports with each port connected to a different switch. This configuration requires that host port interconnects are disabled, which they are by default.

  • Page 48: Connecting Two Data Hosts Through A Zoned Switch

    Connecting Two Data Hosts Through a Zoned Switch Figure 3-7 shows a high-availability, dual-controller connection through a two-zone switch. Each zone can be an independent switch (see Figure 3-6). Zone 0 Zone 1 Controller A Controller B Figure 3-7 High-Availability Dual-Controller Connection Through a Two-Zone Switch to Two Dual-Port Data Hosts Connecting Remote Management Hosts The management host directly manages systems out-of-band over an Ethernet...

  • Page 49: Configuring A System For The First Time

    CH A P T E R Configuring a System for the First Time This chapter describes how to perform first-time configuration on the storage system. It also describes how to perform basic storage configuration to verify that your system is working. This chapter includes the following topics: “Setting Management Port IP Addresses Using the CLI”...

  • Page 50: Setting Management Port Ip Addresses Using The Cli

    Setting Management Port IP Addresses Using the CLI Note – If you used DHCP to set the IP addresses, you do not have to set them using the CLI as described in this section. Ethernet Management ports on controller module A and controller module B are configured with the following default values: Management Port IP Address: 10.0.0.2 (controller A), 10.0.0.3 (controller B) ■...
  • Page 51 Your package contents include a micro-DB9-to-DB9 serial cable. If necessary, use a DB9-to-DB25 adapter (not included) for connecting the serial cable to a DB25 serial port on the host computer. 3. Start and configure a terminal emulator, such as HyperTerminal or VT-100, using the display settings in Table 4-1 and the connection settings in Table 4-2.
  • Page 52 4. In the terminal emulator, connect to controller A. 5. Press Enter to display the CLI prompt (#). 6. At the prompt, type the following command to set the values you obtained in Step 1 for each Ethernet management port, first for controller A and then for controller B: set network-parameters ip address netmask netmask gateway gateway controller a|b where:...

  • Page 53: Configuring Your Web Browser For Smu

    9. In the host computer's command window, type the following command to verify Ethernet connectivity, first for controller A and then for controller B: ping IP-address If you cannot your access your system for at least three minutes after changing the IP address, your network might require you to restart the management controller using the serial CLI.

  • Page 54: Logging In To Smu From A Local Management Host

    Logging in to SMU from a Local Management Host To log in to SMU from a local management host: 1. In your web browser’s address field, type the IP address of one of the controller enclosure’s Ethernet management ports and press Enter. The SMU Login page is displayed.

  • Page 55: Configuring Host Ports

    If a time server can provide local time rather than UT, configure the storage ■ devices to use that time server, with no further time adjustment. If no NTP server is present, the date and time are maintained as if NTP had not been enabled.
  • Page 56 2. In the Controller Module Host Port Configuration panels, for each port to which an HBA or switch is attached, set the appropriate link speed. An FC port’s link speed must match the speed of the FC HBA or switch to which the port is connected.

  • Page 57: Creating Virtual Disks

    Creating Virtual Disks Two or more disk drives can be logically combined to form a virtual disk. The combined storage capacity can then be partitioned into volumes. SMU provides both manual and automatic methods for creating virtual disks, as described in its online help and in the reference guide.

  • Page 58: Mapping A Data Host To A Volume

    Mapping a Data Host to a Volume To enable a data host to access a volume you created, you must map the volume to the host. The port World Wide Name (WWN) of each host connected to the system is automatically added to the system’s global host port list. Before mapping a data host to a volume you must identify the data host’s port WWN and a LUN that the host is not using.

  • Page 59: Testing The Configuration

    Testing the Configuration To determine that your system is ready for use, test the configuration as follows: 1. In SMU, select Monitor > Vdisk Status and view the configuration information for each virtual disk. The virtual disk status is Critical during initialization but you can perform I/O to the volume.
  • Page 60 HP StorageWorks 2012fc Modular Smart Array user guide • March 2008...

  • Page 61: Powering The System Off And On

    A P P E N D I X Powering the System Off and On This appendix describes how to power off and power on the system when needed. Powering Off the System The system rarely needs to be powered off. You remove power only when you plan to physically move the system to another location.
  • Page 62 2. Press the power switches at the back of the controller enclosure to the On ( –) position. If the enclosure’s power-on sequence succeeds as described in Step 1, the system is ready to use. HP StorageWorks 2012fc Modular Smart Array user guide • March 2008...

  • Page 63: Federal Communications Commission Notice

    A P P E N D I X Regulatory Compliance and Safety Regulatory Compliance Federal Communications Commission Notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference- free radio frequency spectrum.

  • Page 64: Class B Equipment

    (2) this device must accept any interference received, including interference that may cause undesired operation. For questions regarding your product, visit http://www.hp.com For questions regarding this FCC declaration, contact us by mail or telephone: Hewlett-Packard Company ■ P.O. Box 692000, Mailstop 510101 Houston, Texas 77269-2000 1-281-514-3333 ■...

  • Page 65: Regulatory Compliance Identification Numbers

    Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user's authority to operate the equipment. Cables...

  • Page 66: Laser Safety Warning

    Laser Safety Warning Warning – To reduce the risk of exposure to hazardous radiation: Do not try to open the laser device enclosure. There are no user-serviceable ■ components inside. Do not operate controls, make adjustments, or perform procedures to the laser ■...

  • Page 67: International Notices And Statements

    International Notices and Statements Canadian Notice (avis Canadien) Class A Equipment This Class A digital apparatus meets all requirements of the Canadian Interference- Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Class B Equipment This Class B digital apparatus meets all requirements of the Canadian Interference- Causing Equipment Regulations.

  • Page 68: Bsmi Notice

    Also approved under UL 60950/CSA C22.2 No. 60950-00, Safety of Information ■ Technology Equipment. BSMI Notice Japanese Notice HP StorageWorks 2012fc Modular Smart Array user guide • March 2008...

  • Page 69: Korean Notices

    Korean Notices Safety Battery Replacement Notice Your computer is equipped with a lithium manganese dioxide, a vanadium pentoxide, or an alkaline internal battery or battery pack. There is a danger of explosion and risk of personal injury if the battery is incorrectly replaced or mistreated.

  • Page 70: Taiwan Battery Recycling Notice

    Batteries, battery packs, and accumulators should not be disposed of together with the general household waste. To forward them to recycling or proper disposal, please use the public collection system or return them to HP, an authorized HP Partner, or their agents.

  • Page 71: Japanese Power Cord Notice

    Japanese Power Cord Notice Electrostatic Discharge To prevent damage to the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices.
  • Page 72 Note – For more information on static electricity, or assistance with product installation, contact your HP authorized reseller. Waste Electrical and Electronic Equipment Directive Czechoslovakian Notice Danish Notice Bortskaffelse af affald fra husstande i den Europæiske Union Hvis produktet eller dets emballage er forsynet med dette symbol, angiver det, at produktet ikke må...

  • Page 73: English Notice

    Dutch Notice Verwijdering van afgedankte apparatuur door privé-gebruikers in de Europese Unie Dit symbool op het product of de verpakking geeft aan dat dit product niet mag worden gedeponeerd bij het normale huishoudelijke afval. U bent zelf verantwoordelijk voor het inleveren van uw afgedankte apparatuur bij een inzamelingspunt voor het recyclen van oude elektrische en elektronische apparatuur.

  • Page 74: Estonian Notice

    Estonian Notice Seadmete jäätmete kõrvaldamine eramajapidamistes Euroopa Liidus See tootel või selle pakendil olev sümbol näitab, et kõnealust toodet ei tohi koos teiste majapidamisjäätmetega kõrvaldada. Teie kohus on oma seadmete jäätmed kõrvaldada, viies need elektri- ja elektroonikaseadmete jäätmete ringlussevõtmiseks selleks ettenähtud kogumispunkti. Seadmete jäätmete eraldi kogumine ja ringlussevõtmine kõrvaldamise ajal aitab kaitsta loodusvarasid ning tagada, et ringlussevõtmine toimub viisil, mis kaitseb inimeste tervist ning keskkonda.

  • Page 75: German Notice

    French Notice Élimination des appareils mis au rebut par les ménages dans l'Union européenne Le symbole apposé sur ce produit ou sur son emballage indique que ce produit ne doit pas être jeté avec les déchets ménagers ordinaires. Il est de votre responsabilité...

  • Page 76: Greek Notice

    Greek Notice Hungarian Notice Készülékek magánháztartásban történ selejtezése az Európai Unió területén A készüléken, illetve a készülék csomagolásán látható azonos szimbólum annak jelzésére szolgál, hogy a készülék a selejtezés során az egyéb háztartási hulladéktól eltér módon kezelend . A vásárló a hulladékká vált készüléket köteles a kijelölt gy jt helyre szállítani az elektromos és elektronikai készülékek újrahasznosítása céljából.
  • Page 77 Italian Notice Smaltimento delle apparecchiature da parte di privati nel territorio dell'Unione Europea Questo simbolo presente sul prodotto o sulla sua confezione indica che il prodotto non può essere smaltito insieme ai rifiuti domestici. È responsabilità dell'utente smaltire le apparecchiature consegnandole presso un punto di raccolta designato al riciclo e allo smaltimento di apparecchiature elettriche ed elettroniche.

  • Page 78: Polish Notice

    Lihuanian Notice Nolietotu iek rtu izn cin šanas noteikumi lietot jiem Eiropas Savien bas priv taj s m jsaimniec b s Š ds simbols uz izstr d juma vai uz t iesai ojuma nor da, ka šo izstr d jumu nedr kst izmest kop ar citiem sadz ves atkritumiem. J s atbildat par to, lai nolietot s iek rtas tiktu nodotas speci li iek rtotos punktos, kas paredz ti izmantoto elektrisko un elektronisko iek rtu sav kšanai otrreiz jai p rstr dei.

  • Page 79: Portuguese Notice

    Portuguese Notice Descarte de Lixo Elétrico na Comunidade Européia Este símbolo encontrado no produto ou na embalagem indica que o produto não deve ser descartado no lixo doméstico comum. É responsabilidade do cliente descartar o material usado (lixo elétrico), encaminhando-o para um ponto de coleta para reciclagem.

  • Page 80: Spanish Notice

    Slovenian Notice Spanish Notice Eliminación de residuos de equipos eléctricos y electrónicos por parte de usuarios particulares en la Unión Europea Este símbolo en el producto o en su envase indica que no debe eliminarse junto con los desperdicios generales de la casa. Es responsabilidad del usuario eliminar los residuos de este tipo depositándolos en un "punto limpio"...

  • Page 81: Swedish Notice

    Swedish Notice Bortskaffande av avfallsprodukter från användare i privathushåll inom Europeiska Unionen Om den här symbolen visas på produkten eller förpackningen betyder det att produkten inte får slängas på samma ställe som hushållssopor. I stället är det ditt ansvar att bortskaffa avfallet genom att överlämna det till ett uppsamlingsställe avsett för återvinning av avfall från elektriska och elektroniska produkter.
  • Page 82 HP StorageWorks 2012fc Modular Smart Array user guide • March 2008...

  • Page 83: Index

    Index host ports enabling port interconnects, 55 accessing setting FC loop IDs, 55 SMU, 54 setting FC topology, 55 the CLI, 50 loop or point-to-point topology, 41, 55 accumulators, 70 switch attach configurations, 40, 45 Avis Canadien, regulatory compliance connecting notice, 67 AC power, 35 controller and drive enclosures, 32...
  • Page 84 powering on, 61 cord. See power cord testing connections, 36 current rating, 70 ESD (electrostatic discharge) prevention measures, 71 storing products, 71 data hosts transporting products, 71 connecting to controller enclosures European Union, regulatory compliance mapping to volumes, 58 notice, 67 system requirements, 39 date and time, setting, 54 declaration of conformity, 64...
  • Page 85 SAS Out port status, 22 status, 14 IEC EMC, worldwide regulatory compliance notice, 67 Unit identification (UID), 14 indicators, See LEDs Unit Locator, 18, 21 installing enclosures lithium battery, 69 checklist, 23 loop topology, 41 in a rack, 28 safety precautions, 26 installing required host software and drivers managing storage systems SES driver, 40...
  • Page 86 preparing, 27 storage website, 10 recycling, battery, 70 straps, ground boot, 71 recycling, Taiwan EPA battery, 70 heel, 71 regulatory compliance toe, 71 information number, 65 Subscriber’s choice website, 10 notices BSMI, 68 Subscriber’s choice, HP, 10 Canada, 67 switch attach configurations, 40, 45 Class A, 63 Class B, 64 European Union, 67...
  • Page 87 using, 71 Index...
  • Page 88 HP StorageWorks 2012fc Modular Smart Array user guide • March 2008...

This manual is also suitable for:

Storageworks 2012fc

Table of Contents