Advertisement
Available languages
Available languages
Installation
Connecting and installing the
Installing the optical cable
optical cable connection box
connection box
• When installing the optical cable
Connecting the optical cable
connection box with the velcro
tape.
• Connect the optical cable to the
Install the optical cable connection box
optical cable connection box.
using the velcro tape in the ample
space of the console box.
Velcro tape (hard)
Optical cable
Velcro tape (soft)
• When installing the optical cable
connection box with the lock tie.
Wrap the optical cable and connection
box with the protection tape and fasten
with the power code using the lock tie.
Wrap with the protection tape
Fasten with the lock tie
Note:
Installing the unit
•
Before finally installing the unit, connect the
wiring temporarily, making sure it is all connect-
Mounting with brackets
ed up properly, and the unit and the system work
properly.
•
Use only the parts included with the unit to
ensure proper installation. The use of unautho-
rized parts can cause malfunctions.
Tapping screw (4 × 12 mm)
•
Consult with your nearest dealer if installation
requires the drilling of holes or other modifica-
tions of the vehicle.
•
Install the unit where it does not get in the dri-
ver's way and cannot injure the passenger if there
Screw
is a sudden stop, like an emergency stop.
(4 × 8 mm)
•
When mounting this unit, make sure none of the
leads are trapped between this unit and the sur-
rounding metalwork or fittings.
•
Do not mount this unit near the heater outlet,
Bracket
where it would be affected by heat, or near the
Car mat or chassis
doors, where rainwater might splash onto it.
•
Before drilling any mounting holes always check
Drill 2 to 2.5 mm
behind where you want to drill the holes. Do not
diameter holes.
drill into the gas line, brake line, electrical wiring
Do not close this area.
or other important parts.
•
If this unit is installed in the passenger compart-
ment, anchor it securely so it does not break free
Mounting with velcro tape
while the car is moving, and cause injury or an
Thoroughly wipe off the surface before affixing
accident.
the velcro tape.
•
If this unit is installed under a front seat, make
sure it does not obstruct seat movement. Route
all leads and cords carefully around the sliding
mechanism so they do not get caught or pinched
in the mechanism and cause a short circuit.
Velcro tape
Car mat or chassis
<ENGLISH>
Routing the optical cable
Mounting the clamp
The clamp is used to secure the optical cable
when using it. The other clamp is installed on the
Precaution:
back side of the head unit similarly and used to
•
Try not to bend the optical cable sharply. If it is
secure the optical cable.
necessary to bend it sharply, make sure that the
bending radius is at least 25 mm (1 inch), other-
1. Insert the clamp in the direction
wise the cable will not transfer signals properly
and so this unit will not work properly.
indicated in the figure, and turn it 90
•
Route the optical cable so that nothing heavy
degrees to lock.
rests on it, and so that it cannot be stepped on or
caught in anything – for instance, a door.
•
Make a loop of diameter at least 200 mm (7-7/8
inches) with the remaining optical cable so that
the cable does not get strained.
•
When plugging the optical cable into the unit,
use the supplied cable clamps to prevent the
cable from being bent sharply.
•
Route the optical cable so that it does not get
caught in moving parts such as the gear shift,
hand brake, or seat sliding mechanism. Keep the
Clamp
cable away from hot spots, such as near the
heater outlet.
Using the corrugated tube
2. Secure the optical cable.
To prevent the optical cable from being strained,
use the corrugated tube after cutting it to the cor-
rect length.
• Insert the optical cable into the cor-
rugated tube.
Optical cable
Optical cable
Corrugated tube
Advertisement
