Summary of Contents for Haier 46EP14S - ANNEXE 247
Page 1
46" PLASMA TV/MONITOR OWNER'S MANUAL Model# 46EP14S Please read this manual carefully before using this TV set and keep it for future reference.
LITERATURE ACCOMPANYING THE APPLIANCE. FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
8)Power Source ---this TV should be operated only from the type of power source indicated on the rating label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company.
Page 4
Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation. e.If the unit has been dropped or damaged in any way.
Page 5
Safety Instructions Table of Contents Before Use & Installation Accessories Powering up your plasma Warranty...
Page 6
Operating environment: Temperature : 32 F~104 F (0 ~40 ) Humidity : 20% to 85% non-condensing Atmospheric pressure : 800 to 1100hPa...
Page 10
Powering up your plasma: Cord cord Flip to the on position light unit...
Page 11
Monitor control buttons : Functions as follows will be displayed. Select desired input source , and use button to look in the selection. & screen adjustments Music Signal source Picture adjustments Channel programing & Picture preference (circular display).
Page 13
C. - PC module VHF/UHF 1. VHF/UHF: Connect antenna or CATV 75 coaxial cable to recive TV/CATV signal. 2. TV audio: Connect audio amplifier or other TV that with audio input. 3. Video: Connect monitor or TV that with video input.
Page 15
RATING SLEEP switch off show up Select the correct signal source in the modules. TV/CTV Automatically chooses the correct PC source...
Page 16
,¡° ,¡° SAP¡± SAP¡± or ¡° or ¡° Mono¡± Mono¡± sound system. sound system. Press again to reactivate picture. Select the desired ratio. (You can switch among six screen sizes.) Direct access to closed caption. Rating button. Sleep times button.
Page 17
Insert 2 AA alkaline batteries as shown. range 33 feet RATING SLEEP...
Page 19
Connect D-SUB(15PIN) to analog RGB output interface (Input option RGB). Conncet DVI to digital RGB output interface (Input option RGB). Note: 1.The DVI connector of the Display is DVI-I, which does not support analog signal input. 2. The RS-232 connector provides a transmission interface for professional technicians to update firmware, without providing additional communication functions.
Page 20
The S-Video terminal: connects to the Y/C S-Video output of a video output devices(such as S-VHS or DVD). The audio should input via Audio 2 (INPUT Option S-Video). CVBS In terminal connects to the CVBS(Video) output of a device(such as...
Page 21
Input and output connection A/V OUT TV module VHF/UHF: Connect antenna or CATV 75 coaxial cable to receive TV/CATV signal. Audio Out: Connect to an input of an external amplifier. Video Out: Connect to an input of an external monitor or TV.
Page 22
SPEAKER WIRE SPEAKER WIRE Press the speaker terminals clips down and insert the speakers wire(red to red and black to black),making sure a good contact with the terminal is obtained. Then close the terminal clips. Pg 27...
Page 23
POWER key to turn on the Display. The power indicator will change from red to green. Press the POWER key again turn off the Display. The power indicator will change from green back to red. RATING SLEEP RATING SLEEP TV/CATV...
Page 25
Channel programing & Picture preference (circular display). Use the keys to adjust the OSD Menu up and down. These keys can also be used at any time to access the Quick RATING SLEEP Menu . The Quick Menu display sequences is as follows: controls the select function.
Page 26
ASPECT RATIO: by press the WIDE key, you can change the aspect ratio according to your preference . You can then restore the image to its original size by pressing the WIDE key again until your original image is restored.
Page 28
Note: Press to scroll up & down an to adjust the settings. TV function For TV function feature please prefer to page 31-32.
Page 30
YCbCr TV Press menu on display for image page to be displayed. The Image page is used to enable and disable the PIP, set the PIP size and select the PIP source and position. See page 32 for detail information.
Page 39
39.64 x 22.33 44.8 x 27.20 x 3.85 81.41 bs TV module TV-Audio output terminal video output terminal VHF/UHF input terminal 2xAA Alkalines ,1xPower Cord, Owner`s...
Page 41
Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC. Note: Do not allow a still picture to be displayed for an extended period, as this can cause a permanent after-image to remain on the Plasma TV.
Page 43
PERIOD(s) FROM THE DATE OF PURCHASE please call 1-877-337-3639. SET FORTH BELOW. Some states do not What to do to obtain service: ship or carry in allow limitations on how long an implied your product to an authorized service dealer warranty lasts, so the above limitation may or center .Be sure to have proof of purchase.
Page 44
D A T E D P R O O F O F P U R C H A S E R E Q U I R E D F O R Q A R R A N T U S...