Related Manuals for Electrolux EI15IM55GS0
Summary of Contents for Electrolux EI15IM55GS0
- Page 1 Use & Care Guide Ice Maker Guia de Uso y Cuidado Máquina de hielo Guide d’utilisation et d’entretien Machine à glaçons 241927600 November 2007...
-
Page 2: Finding Information
Product Registration Card in the mail. PLEASE READ all instructions completely before Please record the purchase date of your Electrolux attempting to install or operate the unit. unit and your dealer’s name, address and All ice makers require a connection to both a telephone number. -
Page 3: Table Of Contents
Finding Information Table of Contents Finding Information ..........2 Operation............14 Please read and save this guide ..........2 Normal Operation ..............14 Keep a record for quick reference ...........2 Ice Cube Thickness ...............14 Questions? ................2 Ice Dispenser Operation and Care .........14 Table of contents..............3 Ice Cube Thickness Adjustment ..........15 Drain Pump ................15... -
Page 4: Safety
• Use only genuine Electrolux children may not easily climb inside. replacement parts. Imitation parts can reduce ice rate, cause water to overflow... -
Page 5: Installation
Figure 1 Model EI15IM55GS can be installed using a gravity drain or the Electrolux EIMP60, optional drain pump kit. Follow these guidelines when installing drain lines to prevent water from flowing back into the ice... -
Page 6: Connecting A Drain Pump
EIMP60 drain pump. The Electrolux EIMP60 drain pump is available through your Dealer, or direct from Electrolux with complete installation instructions. If a pump other than the Electrolux EIMP60 drain pump is to be used, it must meet the following specifications: •... -
Page 7: Site Preparation
(see Figure which will cause the ice in the bin to melt pre- 2). Electrolux stainless steel models require maturely. Remember that floors near drains have a minimum 2-3/4 inch handle clearance when a tendency to slope towards the drain. -
Page 8: Water Supply Connection
However, make certain that the tubing is not pinched or damaged during installation. • Electrolux recommends the use of copper tubing for installation. DO NOT use plastic water supply line since it may crack or rupture with age and may cause water damage to your house. -
Page 9: Leveling
Leveling Leveling the unit Use a level to check the levelness of the ice maker from front to back and from side to side (see Figure 10). CHECK LEVEL Figure 10 If the ice maker is not level, adjust the feet on the corners of the unit as necessary (see Figure 11). -
Page 10: Door Reversal
Door Reversal Reversing the Door (some models) Remove plastic screw plugs (3 top and 3 All Electrolux units may be left or right hand bottom) from new hinge location (see Figure opening. The door opening is easily reversed by 14), and remove hinge pin hole plug in top of moving the hinge hardware to the opposite side door (see Figure 15). - Page 11 Door Reversal Remove the two door closer inserts from the Holding door upright with top of door tilted existing bottom hinge and install as shown on forward, place hole of door pivot plate on the new bottom hinge (see Figure 17). bottom hinge screw pin (see Figure 19).
-
Page 12: Adjusting The Door
Door Adjustment Adjusting the Door If door edge opposite the hinges needs to move up, move plate toward outside of door. If door edge needs to move down, move Your door is aligned at the factory before shipment. plate toward inside of door (see Figure 22). Occasional re-adjustment may be necessary, Repeat until top edge of door is parallel with especially if an overlay panel is installed. -
Page 13: Built-In Installation / Start-Up
ARROW & OTHER FUNCTIONS POWER ARROW DISPLAY Your Electrolux product has been designed for either free-standing or built-in installation. When built-in, your ice maker does not require additional air space for top, sides or rear. However, the front Figure 24 grille must NOT be obstructed. -
Page 14: Operation
Ice Cube Thickness ICE BRIDGE DIMPLE TOO DEEP Your Electrolux ice maker uses advanced technology to make ice that is crystal clear. This technology cascades a flow of water over a chilled ice mold that is mounted vertically so no water sits in it. -
Page 15: Ice Cube Thickness Adjustment
Operation Ice Cube Thickness Adjustment SAMPLE AREA Interval - As Required Ice thickness adjustments are made using the control panel as follows: LIGHT, DOWN BLACKOUT MODE & OTHER FUNCTIONS ARROW DISPLAY ARROW POWER ICE005 Figure 28 Figure 27 To enter the thickness adjustment mode: a. -
Page 16: Maintenance
Maintenance Special Considerations • If any surface discolors or rusting appears, clean it quickly with Bon-Ami or Barkeepers • For best performance, keep the unit out of Friend Cleanser and a non-abrasive cloth. direct sunlight. Always clean in the direction of the grain. •... -
Page 17: Condenser Cleaning - Every 3 Months
To remove and replace the grille for access to the condenser fins follow this procedure (see Figure CAUTION 29): Use only Electrolux Ice Machine Cleaner (part Remove the screws at each end of the grille. number EIM30046). Remove the grille. - Page 18 POWER button. The display will show “CL” to confirm the beginning of the cleaning cycle. When water begins to flow over the evaporator (approximately 3 minutes), add one package of Electrolux Ice Machine Cleaner to the water reservoir.
-
Page 19: Inlet Screen Cleaning - Every Year
Maintenance / Storage, Vacation and Moving Inlet Screen Cleaning — Draining for non-use Every Year If the unit is to be stored, moved or not used for extended periods, it will be necessary to drain the The solenoid valve inlet screen must be cleaned at system of water. -
Page 20: Troubleshooting
Troubleshooting Before You call For Service If the unit appears to be malfunctioning, read through Normal Operation first. If the problem persists, check the Troubleshooting Guide. Locate the problem in the guide and refer to the cause and its remedy before calling for service. -
Page 21: If Service Is Required
Troubleshooting Troubleshooting – What to check when problems occur Problem Possible Cause Remedy Poor ice quality (soft or unclear). Poor incoming water quality. Consult a qualified plumber to test the water quality and recommend appropriate treatment. Ice-making system is dirty. Run unit through automatic clean cycle. -
Page 22: Warranty Information
State of Alaska) In the U.S.A., your appliance is warranted by Electrolux Home Products, Inc. We authorize no person to change or add to any of our obligations under this warranty. Our obligations for service and parts under this warranty must be performed by us or an authorized Electrolux Home Products, Inc.