Advertisement

Available languages

Available languages

Quick Links

22in Recycler
Model No. 20338—Serial No. 310000001 and Up
Replacement parts are available from an Authorized Service Dealer or at www.shoptoro.com.
Introduction
Read this information carefully to learn how to operate
and maintain your product properly and to avoid injury
and product damage. You are responsible for operating
the product properly and safely.
You may contact Toro directly at www.Toro.com for
product and accessory information, help finding a dealer,
or to register your product.
Whenever you need service, genuine Toro parts,
or additional information, contact an Authorized
Service Dealer or Toro Customer Service and have
the model and serial numbers of your product ready.
Figure 1 identifies the location of the model and serial
numbers on the product.
1. Model and serial number plate
Write the product model and serial numbers in the space
below:
Model No.
Serial No.
This manual identifies potential hazards and has safety
messages identified by the safety alert symbol (Figure 2),
which signals a hazard that may cause serious injury
© 2011—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
Figure 1
Register at www.Toro.com.
Lawn Mower
or death if you do not follow the recommended
precautions.
1. Safety alert symbol
This manual uses 2 words to highlight information.
Important calls attention to special mechanical
information and Note emphasizes general information
worthy of special attention.
The engine exhaust from this product
contains chemicals known to the State of
California to cause cancer, birth defects,
or other reproductive harm.
Important: This engine is not equipped with a
spark arrester muffler. It is a violation of California
Public Resource Code Section 4442 to use or operate
the engine on any forest-covered, brush-covered, or
grass-covered land. Other states or federal areas
may have similar laws.
This spark ignition system complies with Canadian
ICES-002.
The enclosed Engine Owner's Manual is supplied
for information regarding the US Environmental
Protection Agency (EPA) and the California
Emission Control Regulation of emission systems,
maintenance, and warranty. Replacements may be
ordered through the engine manufacturer.
For models with stated engine horsepower, the gross
horsepower of the engine was laboratory rated by the
engine manufacturer in accordance with SAE J1940.
Form No. 3364-894 Rev B
Operator's Manual
Figure 2
WARNING
CALIFORNIA
Proposition 65 Warning
Original Instructions (EN)
Printed in the USA
All Rights Reserved

Advertisement

Table of Contents
loading

Summary of Contents for Toro Recycler 20338

  • Page 1 You are responsible for operating the product properly and safely. Figure 2 You may contact Toro directly at www.Toro.com for 1. Safety alert symbol product and accessory information, help finding a dealer, or to register your product.
  • Page 2: General Operation

    As configured to meet safety, emission, and operating • Do not operate machine without the entire grass requirements, the actual engine horsepower on this class catcher, discharge guard, rear guard, or other safety of lawn mower will be significantly lower. protective devices in place and working.
  • Page 3: Safe Handling Of Gasoline

    General Service • Keep children out of the mowing area and under the watchful care of a responsible adult other than the • Never operate machine in a closed area. operator. • Keep all nuts and bolts tight to be sure the equipment •...
  • Page 4: Safety And Instructional Decals

    Safety and Instructional Decals Important: Safety and instruction decals are located near areas of potential danger. Replace damaged decals. Manufacturer's Mark 1. Indicates the blade is identified as a part from the original machine manufacturer. 114-7982 1. Warning—read the Operator's Manual. 2.
  • Page 5: Installing The Handle

    Setup Important: Remove and discard the protective plastic sheet that covers the engine. Filling the Engine with Oil No Parts Required Procedure Installing the Handle Important: Your mower does not come with oil in the engine, but it does come with a bottle of oil. No Parts Required Before starting the engine, fill the engine with oil.
  • Page 6: Product Overview

    Product Overview through 5 until the oil level is at the Full mark on the dipstick (Figure 4). Important: Do not overfill the crankcase with oil and run the engine. If you overfilled the crankcase, drain the excess oil until the oil level on the dipstick reads Full;...
  • Page 7: Operation

    Checking the Engine Oil Level Operation Service Interval: Before each use or daily Filling the Fuel Tank Note: Max. fill: 20 oz. (0.59 l), type: SAE 30 detergent oil with an API service classification of SF, SG, SH, SJ, DANGER SL, or higher.
  • Page 8: Adjusting The Cutting Height

    Adjusting the Cutting Height mm); 3-1/4 inches (83 mm); 3-5/8 inches (92 mm); and 4 inches (102 mm). WARNING Starting the Engine Adjusting the cutting height may bring you into contact with the moving blade, causing serious 1. Hold the blade control bar against the handle injury.
  • Page 9: Using The Self-Propel Drive

    Check the grass bag frequently. If it is damaged, install a new Toro replacement bag. Figure 12 If the side discharge chute is on the mower, remove it (refer to Removing the Side Discharge Chute) before 1.
  • Page 10: Removing The Grass Bag

    2. Install the grass bag, ensuring that the pins on the bag rest in the notches on the handle (Figure 13). 3. Lower the rear deflector. Removing the Grass Bag To remove the bag, reverse the steps above. Operating the Bag-on-Demand Lever The bag-on-demand feature allows you to either collect or recycle grass and leaf clippings while the grass bag is attached to the mower.
  • Page 11: Operating Tips

    • For best performance, install a new blade before the cutting season begins. • Replace the blade when necessary with a Toro replacement blade. Cutting Grass • Cut only about a third of the grass blade at a time.
  • Page 12: Cutting Leaves

    – Set the cutting height on the front wheels one notch lower than the rear wheels. For example, set the front wheels at 2-1/8-inch (54 mm) and the rear wheels at 2-1/2 inches (64 mm). Cutting Leaves • After cutting the lawn, ensure that half of the lawn shows through the cut leaf cover.
  • Page 13: Recommended Maintenance Schedule(S)

    • Refer to your engine operator's manual for any additional yearly maintenance procedures. Important: Refer to your engine operator's manual for additional maintenance procedures. Note: Replacement parts are available from an Authorized Service Dealer (go to www.toro.com to find the nearest dealer) or at www.shoptoro.com. Preparing for Maintenance hand fuel pump to remove the fuel.
  • Page 14: Replacing The Air Filter

    Replacing the Air Filter Service Interval: Every 25 hours 1. Use a screw driver to open the air filter cover (Figure 18). Figure 18 Figure 20 1. Dipstick 2. Replace the air filter (Figure 19). 4. Tip the mower onto its side with the air filter up to drain the used oil out through the oil fill tube (Figure 21).
  • Page 15: Replacing The Blade

    Replacing the Blade Service Interval: Yearly Important: You will need a torque wrench to install the blade properly . If you do not have a torque wrench or are uncomfortable performing this procedure, contact an Authorized Service Dealer. Examine the blade whenever you run out of gasoline. If the blade is damaged or cracked, replace it immediately.
  • Page 16: Cleaning The Mower

    Cleaning the Mower Service Interval: Before each use or daily WARNING The mower may dislodge material from under the mower housing. • Wear eye protection. • Stay in the operating position (behind the handle) when the engine is running. Figure 24 •...
  • Page 17: Preparing The Mower For Storage

    Storage 1. Loosen the handle knobs until you can move the upper handle freely. Store the mower in a cool, clean, dry place. 2. Fold the upper handle forward as shown in Figure 27. Important: Route the cables to the outside of Preparing the Mower for the handle knobs as you fold the handle.
  • Page 18 Notes:...
  • Page 19 Notes:...
  • Page 20: The Toro Total Coverage Guarantee

    Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.
  • Page 21: Manual Del Operador

    Nota resalta información general Servicio Técnico Autorizado o con Asistencia al Cliente que merece una atención especial. Toro, y tenga a mano los números de modelo y serie de su producto. Figura 1 identifica la ubicación de los ADVERTENCIA números de modelo y serie en el producto.
  • Page 22: Operación General

    En los casos en que se indica la potencia en cv del • No utilice la máquina si usted está descalzo o lleva motor, la potencia bruta del motor fue calculada en el sandalias. Lleve siempre calzado fuerte. laboratorio por el fabricante del motor, con arreglo a lo •...
  • Page 23: Manejo Seguro De La Gasolina

    pueden causar caídas y resbalones. La hierba alta • Retire un equipo con motor de gasolina del camión puede ocultar obstáculos. o del remolque y repóstelo en el suelo. Si esto no es posible, reposte el equipo desde un recipiente •...
  • Page 24 • No cambie los ajustes del regulador del motor ni haga funcionar el motor a una velocidad excesiva. • Revise o sustituya las pegatinas de seguridad e instrucciones cuando sea necesario.
  • Page 25: Pegatinas De Seguridad E Instrucciones

    Pegatinas de seguridad e instrucciones Importante: Hay pegatinas de seguridad e instrucciones colocadas cerca de zonas de potencial peligro. Sustituya cualquier pegatina dañada. Marca del fabricante 1. Indica que la cuchilla ha sido identificada como pieza del fabricante original de la máquina. 114-7982 1.
  • Page 26: Montaje

    Montaje Importante: Retire y deseche la hoja protectora de plástico que cubre el motor. Llenado del cárter de aceite No se necesitan piezas Procedimiento Instalación del agarradero Importante: El cortacésped se suministra sin aceite en el motor, pero incluye una botella de No se necesitan piezas aceite.
  • Page 27 El producto Nota: Si el nivel de aceite está por debajo de la marca Añadir de la varilla, vierta una pequeña cantidad de aceite lentamente en el tubo de llenado, espere 3 minutos, y repita los pasos 3 a 5 hasta que el nivel llegue a la marca Lleno de la varilla (Figura 4).
  • Page 28: Operación

    Operación Cómo llenar el depósito de combustible PELIGRO La gasolina es altamente inflamable y explosiva. Un incendio o una explosión provocado(a) por la gasolina puede causarle quemaduras a usted y a otras personas. • Para evitar que una carga estática incendie la gasolina, coloque el recipiente y/o el cortacésped directamente sobre el suelo antes de repostar, no en un vehículo o sobre otro objeto.
  • Page 29: Ajuste De La Altura De Corte

    Verificación del nivel de aceite Ajuste de la altura de corte del motor ADVERTENCIA Intervalo de mantenimiento: Cada vez que se utilice Al ajustar la altura de corte, usted podría tocar la o diariamente cuchilla en movimiento, lo que podría causarle graves lesiones.
  • Page 30: Cómo Arrancar El Motor

    Uso de la transmisión Nota: Los ajustes de altura de corte son: 1 pulgada (25 mm); 1-3/8 pulgadas (35 mm); 1-3/4 pulgadas autopropulsada (44 mm); 2-1/8 pulgadas (54 mm); 2-1/2 pulgadas (64 mm); 2-7/8 pulgadas (73 mm); 3-1/4 pulgadas Para operar la transmisión autopropulsada, apriete (83 mm);...
  • Page 31: Ensacado De Los Recortes

    Compruebe frecuentemente la bolsa de recortes. Si está dañada, instale una bolsa de recambio Toro nueva. Si el conducto de descarga lateral está instalado en el Figura 13 cortacésped, retírelo (consulte Cómo retirar el conducto...
  • Page 32 Figura 14 Figura 15 1. Palanca de ensacado a demanda (en la posición de 1. Limpiar aquí ensacado) • Para reciclar los recortes de hierba y hojas, presione Descarga lateral de los hacia dentro el botón de la palanca de ensacado a demanda y mueva la palanca hacia atrás hasta que recortes salga el botón de la palanca.
  • Page 33: Consejos De Operación

    • Sustituya la cuchilla cuando sea preciso por una cuchilla de repuesto Toro. Cómo cortar la hierba • Corte solamente un tercio de la hoja de hierba cada vez. No corte con un ajuste inferior a 54 mm (2-1/8 pulg.) a menos que la hierba sea escasa, o a...
  • Page 34 – Cambiar la cuchilla o mandarla a afilar. – Caminar más despacio mientras siega. – Elevar la altura de corte del cortacésped. – Cortar el césped con más frecuencia. – Solapar los pasillos de corte en lugar de cortar un pasillo completo en cada pasada.
  • Page 35: Calendario Recomendado De Mantenimiento

    Importante: Consulte en el Manual del operador del motor procedimientos adicionales de mantenimiento. Nota: Puede adquirir piezas de repuesto en un Servicio Técnico Autorizado (vaya a www.toro.com para encontrar el distribuidor más cercano) o en www.shoptoro.com. Preparación para el Importante: Antes de inclinar el cortacésped...
  • Page 36: Cambio Del Filtro De Aire

    Cambio del filtro de aire Intervalo de mantenimiento: Cada 25 horas 1. Utilice un destornillador para abrir la tapa del filtro de aire (Figura 18). Figura 18 Figura 20 1. Varilla 2. Cambie el filtro de aire (Figura 19). 4. Coloque el cortacésped de lado con el filtro de aire hacia arriba para drenar el aceite usado a través del tubo de llenado de aceite (Figura 21).
  • Page 37 11. Instale la varilla firmemente en el tubo de llenado de aceite. 12. Elimine correctamente el aceite usado en un centro de reciclaje homologado. Cómo cambiar la cuchilla Intervalo de mantenimiento: Cada año Importante: Usted necesitará una llave dinamométrica para instalar la cuchilla correctamente .
  • Page 38 Limpieza del cortacésped Intervalo de mantenimiento: Cada vez que se utilice o diariamente ADVERTENCIA El cortacésped puede soltar material de debajo de la carcasa. • Lleve protección ocular. • Permanezca en la posición de operación (detrás del manillar) cuando el motor está en marcha. Figura 24 La figura está...
  • Page 39 Almacenamiento Cómo plegar el manillar ADVERTENCIA Almacene el cortacésped en un lugar fresco, limpio y seco. Si pliega o despliega el manillar de forma incorrecta, pueden dañarse los cables, creando unas Preparación del cortacésped condiciones de operación inseguras. para el almacenamiento •...
  • Page 40 Países fuera de Estados Unidos o Canadá Los clientes que compraron productos Toro exportados de los Estados Unidos o Canadá deben ponerse en contacto con su Distribuidor Toro para obtener pólizas de garantía para su país, provincia o estado. Si por cualquier razón usted no está satisfecho con el servicio ofrecido por su distribuidor, o si tiene dificultad en obtener información sobre la garantía, póngase en contacto con el importador Toro.

Table of Contents