ENGLISH (Original instructions) SPECIFICATIONS Model: HR008G HR009G Capacities Concrete 30 mm Core bit 80 mm Diamond core bit (dry type) 80 mm Steel 13 mm Wood 32 mm No load speed 0 - 840 min Blows per minute 0 - 4,500 min Rated voltage D.C.
Intended use Vibration The tool is intended for hammer drilling and drilling in The following table shows the vibration total value brick, concrete and stone as well as for chiselling work. (tri-axial vector sum) determined according to applica- It is also suitable for drilling without impact in wood, ble standard.
In cold weather or when the tool has not been EC Declaration of Conformity used for a long time, let the tool warm up for a while by operating it under no load. This For European countries only will loosen up the lubrication. Without proper The EC declaration of conformity is included as Annex A warm-up, hammering operation is difficult.
Page 15
Avoid storing battery cartridge in a con- causing fires, personal injury and damage. It will tainer with other metal objects such as also void the Makita warranty for the Makita tool and nails, coins, etc. charger. Do not expose battery cartridge to water or rain.
25. When storing the wireless unit, keep it in the it may accidentally fall out of the tool, causing injury to supplied case or a static-free container. you or someone around you. 26. Do not insert any devices other than Makita CAUTION: Do not install the battery cartridge wireless unit into the slot on the tool.
If no improvement can be found by restoring protection CAUTION: If the lamp goes off after blinking system, then contact your local Makita Service Center. for a few seconds, the active feedback sensing technology is not working properly. Ask your Switch action local Makita Service Center for repair.
Page 18
Rotation with hammering Reversing switch action For drilling in concrete, masonry, etc., rotate the action ► Fig.6: 1. Reversing switch lever mode changing knob to the symbol. Use a tungsten carbide tipped bit (optional accessory). CAUTION: Always check the direction of ► Fig.9: 1.
16. In the event the tool is dropped, it must be if the screws are not tightened. tagged and removed from service, and should be inspected by a Makita Factory or Authorized CAUTION: Always use a locking carabiner Service Center.
Depth gauge ASSEMBLY The depth gauge is convenient for drilling holes of uniform depth. CAUTION: Always be sure that the tool is Press and hold the lock button, and then insert the switched off and the battery cartridge is removed depth gauge into the hex hole.
NOTE: If you connect a vacuum cleaner to the dust NOTICE: Do not use the dust collection system cup set, remove the dust cap before connecting it. for core drilling or chiseling. ► Fig.28: 1. Dust cap NOTICE: Do not use the dust collection system for metal or wood.
Beating dust on the filter Replacing filter of dust case Remove the dust case while pressing down the CAUTION: Do not turn the dial on the dust latch lever of the dust case. case while the dust case is removed from the ► Fig.43: 1.
Page 23
For model HR008G Hammer drilling operation Optional accessory CAUTION: There is tremendous and sudden Attach the chuck adapter to a keyless drill chuck to twisting force exerted on the tool/drill bit at the time of which 1/2"-20 size screw can be installed, and then hole break-through, when the hole becomes clogged install them to the tool.
Page 24
The wireless activation function enables clean and com- NOTE: A Makita vacuum cleaner supporting the fortable operation. By connecting a supported vacuum wireless activation function is required for the tool cleaner to the tool, you can run the vacuum cleaner registration.
Page 25
Set the stand-by switch on the vacuum cleaner to NOTE: The wireless activation lamp on the tool will "AUTO". stop blinking in blue when there is no operation for ► Fig.61: 1. Stand-by switch 2 hours. In this case, set the stand-by switch on the vacuum cleaner to "AUTO"...
Page 26
Troubleshooting for wireless activation function Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace- ment parts for repairs. State of abnormality Probable cause (malfunction) Remedy The wireless activation lamp does The wireless unit is not installed into Install the wireless unit correctly.
Depth gauge To maintain product SAFETY and RELIABILITY, • Blow-out bulb repairs, any other maintenance or adjustment should • Dust cup be performed by Makita Authorized or Factory Service • Dust cup set Centers, always using Makita replacement parts. Spacer (for HR008G) • Hook set •...